similar to: How i know the version of my vpmadt032 firmware

Running Asterisk 1.6.2.9, DAHDI 2.3.0.1, CentOS 5.5 (update to date as of a week ago), I've installed a Digium AEX800P with 2 X400M FXO Modules and 1 VPMADT032 Module, hooked up to 5 analog lines. I get the error message referenced in the subject in my dmesg output everytime I load / reload DAHDI using the command "system dahdi start/restart". When I make an outbound call over

I updated an AsteriskNow system to 2.6.18-194.26.1.el5 with yum update. Upon reboot dahdi modules cannot be found. In yum.log I see that kmod-mISDN, kmod-dahdi-linux and kmod-dahdi-linux-fwload-vpmadt032 were all deleted during the update. I reinstalled the deleted packages but the dahdi modules can still not be found. They do seem to be under /lib/modules/2.6.18-194.17.4.el5, but no for the

Hi I just want to know if anyone have problems with server DELL 1600, Like: Hangup Call. Thanks Ruben

Hi I have a server with the last version of asterisk branches, zaptel branches, 2 Digium Card with TDM800P 16 HPEC channels (Echo Cancelation), 40 Grandstream BT200 and 10 Grandstream GXP2000. zapata.conf echocancel=64 rxgain=0 txgain=0 when i place a call o receive a call, I finish a sentence i hear a ssssssss, AND when the both side talks at the same time i have choppy audio. Any

Hi Asterisk Users, We've been experiencing some tough time regarding a new Asterisk installation connected to the PSTN via an ISDN PRI with a Digium TE121 with the optional VPMADT032 echo cancellation module. For now, I'll focus on something very specific which is summarized on this email's subject. However, here are some general facts for the context: - System pbxfri went

Dear all, i have a problem with a system running - Ubuntu 10.04 ( all updates done ) - ii asterisk 1:1.8.5.0-1digium1~lucid Open Source Private Branch Exchange (PBX) - ii asterisk-dahdi 1:1.8.5.0-1digium1~lucid DAHDI devices support for the Asterisk PBX I also use freepbx 2.9 for the configuration. Hardware is a Dell R410 and a Digium

Hi, I've been getting regular CPU usage spikes(50%-80%), due to asterisk (according to top). I never noticed this on 1.4, and I have top running in the background pretty much all the time. In between those spikes Asterisk stays under 10% CPU usage (I have a transcoder card, which helps). It's very regular, never any missed spike, or any spike in between the regular spikes. I

Aloha, I'm not sure why I'm getting this error, but I can't seem to get chan_dahdi to load. SIP & IAX2 are working fine. Debian 4 w/ 2.6.28 kernel. Asterisk 1.6.1.5, dahdi-linux 2.2.0.2, dahdi-tools-2.2.0 CLI> module load chan_dahdi.so Unable to load module chan_dahdi.so Command 'module load chan_dahdi.so' failed. [Sep 1 10:57:51] WARNING[31696]: pbx.c:4550

I have a server with an asterisk ss7 link connected to a Siemens working well for over a year. A few days ago I started having problems with signaling. I found the following logs in / var / log / messages Sep 12 11:49:25 call3 kernel: [1018427.030959] dahdi: Master changed to TE2/0/2 Sep 12 11:49:25 call3 kernel: [1018427.120740] dahdi: Master changed to TE2/0/1 Sep 12 11:49:26 call3 kernel:

The TDM410P doesn't support 'hvac', only the obsolete TDM400P supports that option was for the old phones that have a neon light (or equivalent LED+ZENER ciruit). Are other phones off the TDM410P (other than the VTECH) working, or is the Vtech the only model with VMWI available to you. I'm not able to check at the moment, I have copied the asterisk-users list, someone else may

Hi All, I have installed asterisk 1.6.2.8 Dahdi: 2.4.0 Digium card: Digium, Inc. Wildcard AEX800 8-port analog card I have configured this card properly and it is working for calls too, But there is issue of one way audio on this outbound routes only, My voice is going to outside pstn number but i am not able to get their audio, I have disabled firewall, selinux is also off. If I am applying

Does anyone know if the TE122 is recognized by any of the 1.2 zaptel drivers? It seems that 1.2.16 knows it not... :) Cheers, j

I just installed an FXS module onto a 4 channel tdm thats about 5 years old and it wont work. Running dmesg I can see the following error: Zapata Telephony Interface Registered on major 196 Freshmaker version: 71 Freshmaker passed register test !!!!!!! LOOP_CLOSE_TRES iREG 1C = 1 should be 1000 !!!!!!! RING_TRIP_TRES iREG 1D = 8000 should be 3600 !!!!!!! COMMON_MIN_TRES iREG 1E = 0 should

Dear asterisk users, We want setup TE121 digium board: Model: Digium TE121: VoiceBus technology allows the TE121 to use an industry standard bus-mastering PCI Express interface. http://www.digium.com/en/products/digital/te121.php My platform Server: HP Proliant 150 G5 OS: UBUNTU x86_64 GNU/Linux Asterisk: 1.4.21.2 zaptel: SVN-branch-1.4-r4662M When we enable zaptel driver for TE121, the

Hello, I've recently given a try to a Digium D70 phone. At the moment, I'm configuring them though config files with a DHCP server and not using DPMA. Of course, I'm connecting them to Asteris (PJSIP stack on 13.7.0). Which is the best place to: - read about past issues - open new tickets for remaining issues. Best regards -------------- next part -------------- An HTML attachment

I just installed a TE820 octal span T1 card, and it's not showing up in dahdi_hardware output. This was installed into a test machine that already has a TDM800P card in it, and that one is showing up and working fine. Is there some kernel module that I'm missing? Lspci: 05:04.0 Ethernet controller: Digium, Inc. Wildcard TDM800P 8-port analog card (rev 11) 21:08.0 Communication

Hi, I'm reading Digium HA8 manual (page 55). It lists several parameters that can be used to configure a BRI port. More precisely, it suggests that : Term, is the last parameter NT/TE is the one just before (starting from the end). If I'm not mistaken, it seems dahdi_genconf generates /etc/dahdi/system.conf files in which both parameters order is reversed : # Span 1: WCBRI/0/0

I have been doing a lot of reading forums and elsewhere but am somehow unable to connect the dots. Here is what I am trying to accomplish initially and then wish for it to grow bigger from here on. I have two POTS (Analog) line that would connect to the Asterisk Box. I have, to begin with 5 IP phones (PoE), all connected to a switch. Asterisk Box with a LAN card also connects to the same switch.

I am having difficulties with customer-bound DTMF being very short & clipped off (and basically unusable, as systems on the customer side aren't recognizing the DTMF digits, and I can barely tell that DTMF is there when I listen on a handset). My system set up as follows: PSTN <--> Metaswitch <-SIP-> Asterisk <-SIP or IAX2-> CPE Asterisk is running Asterisk 10.4.0 on a

TE410P card down. I have three (3) TE410P in one machine running asterisk with SS7. My problems started last week when one of my cards started switching to E1 every time after reboot. I set the following in dahdi.conf and that solve the problem. /etc/modprobe.d/ options wct4xxp t1e1override=0x00 Now all 4 ports on that card is down with Red Alarm. I tried rebooting the machine and