similar to: REGISTER Outboundproxy

Hi All, I'm connecting to my carrier which requires setting of outboundproxy. There has been few cases where the proxy server failed due to network issues and required us to use a secondary one. Is there a timeout or qualify setting for outboundproxy setting in sip.conf? I do appreciate if anyone can help please. Thank you -Abeed -------------- next part -------------- An HTML attachment

I'm having some trouble turning with trunk monitoring while using an outbound proxy. While all other sip messaging (e.g. calls) respects the outboundproxy setting, Options packets from setting qualify=yes do not. Asterisk tried to send the Options message directly to the "host=" IP, instead of the "outboundproxy=" IP as it should, verified with tcpdump. I've done a

Hi, I'm trying to enable sip.conf outboundproxy support in version 1.4.20.1 of Asterisk, but for the tests I made, every calls, even internal SIP calls between extensions are sent over the proxy that I have specified with the outboundproxy=xxx.xxx.xxx.xxx in sip.conf. I think this isn't the expected behaviour, right? Only OUTBOUND calls should go through the proxy, right? Am I doing

Hello, new to asterisk and trying to set it up to work with my voip provider (vbuzzer.com). I am behind a firewall that I don't have access to, to open ports etc. Before using asterisk, I tried vbuzzer's windows client, and linphone and twinklephone which all worked without having to enable nat or stun. However I did have to enter the outboundproxy server to get them to function. Not

So... I'm trying to access CDR(duration) and CDR(billsec) inside h... I keep getting 0. Can I access the CDR function inside a hangup extensions? Asterisk 1.4.13 Thanks, Doug. ____________________________________________________________________________________ Be a better friend, newshound, and know-it-all with Yahoo! Mobile. Try it now.

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Guenther Boelter <gboelter at gmail.com> schrieb: > -----BEGIN PGP SIGNED MESSAGE----- > Hash: SHA256 > > On 05/31/2015 02:31 PM, Luca Bertoncello wrote: > > Hi list! > > > > Now all works as expected, at least in the simulation I did with > > AsteriskNOW. Hopefully it will work later, when Deutsche Telekom

Hi, My asterisk's version is 1.6.0.26. I've couple sip providers and I've for new SIP provider I need define outbound proxy. Everything is ok in peer section (outboundproxy=192.0.2.1). But what about SIP REGISTER messages? I need send SIP register messages also via outbound proxy. How to write SIP OUTBOUND call register statement and send this to proxy? If I define in general

Hello List I work at an SIP Provider and we have added and SBC in front of our Voice Switch to protect it. This requires all our SIP Trunk customers to register via a 'proxy'. I struggle with Asterisk to work over a proxy. This is what I have done so far. register => username at sip.example.com:password at sbc.example.com This works fine, asterisk is sending registrations via the

We're doing callback here. Asterisk dials a number, waits for an answer, plays a prompt, dials a second number, and bridges the channels together. Calls are initiated from the AMI. No problems there. Easy stuff. However, I'd like to know if it's possible to have Asterisk dial the same two numbers simultaneously, play the prompt to the first one that answers, dial the second one and

hi there I'm setting up asterisk@home and I'm using Polycom IP 500 phones. When I call a number that has a digital receptionist (i.e. "dial 1 or such and such, dial 2 for this and that...") the Polycom doesn't seem to send the extra digits. When I try it with X-Lite things appear to work fine, so I think the problem is with the Polycom configuration. Here's some

Hello, I try configuring Quintum DX gateway as link to PSTN for *. Now, I can dial number which is connect to Quintum, and call is diverted to *. I don't know what I should set, if I want call from SIP_phone registred in Asterisk to PSTN via Quitnum. I set in sip.conf account for Quintum [sip_proxy-out] type=peer outboundproxy=QUINTUM_IP , and changed extensions.conf. When

I am trying to configure a Polycom IP4000 for use with Asterisk 1.4.5 on a flat local network. I followed the provisioning guides that I found on the Web, and I have the phone downloading bootrom.ld, sip.ld, and a bunch of configuration files. This all works properly. However, I receive the following error: NOTICE[27345]: chan_sip.c:14725 handle_request_register: Registration from

Darryl Moore <darryl at moores.ca> schrieb: > Ahh. Seen that before! That suggests to me that you don't have your > sip.conf records setup right. > > What's your sip.conf look like? Well, here what I wrote in my sip.conf: register => 00493511111111:MYSECRET at pbxluca/00493511111111 register => 00493512222222:MYSECRET at pbxfax/00493512222222 register =>

Hello i am trying to setup sipgate gateway i can get incoming calls fine, but when i dial in and then try to dial out i get this in asterisk command line -- Called 01179248615 at sipgate [Sep 18 13:58:30] NOTICE[28232]: chan_sip.c:17885 handle_response_invite: Failed to authenticate on INVITE to '"01179553708" <sip:SIP-ID at sipgate.co.uk>;tag=as30eb9dd1' --

I've set up plenty of Asterisk boxes but never one that had to deal with a proxy server to be able to use a line. Using "X-Lite" I have no issue with settings as follows: Display Name: Any Name User name: 00575000010XXXX Password: 00575000010XXXX Authorization user name: <blank> Domain: directnationalloan.com Checked "Register with domain" and "Send outbound

Hello, I installed Asterisk 1.6.2.17.3 ( latest as of yesterday ) and had multiple problems with DTMF. I have two machines, we'll call them asterisk and asterisk-pri. Asterisk does IVR and asterisk-pri has a PRI card in it and connects to the PSTN. The two servers communicate via SIP with RFC2833. I setup logger.conf on both machines to display DTMF to the console. Both are built from

I'm stumped on this one and any help would be greatly appreciated. I'm just trying to get my Polycom 601 to have multiple extensions on it. For example, on line 1 I want extension 21, on line 2 I want extension 22, and on line 3 I want extension 23. Ideally I'd actually have each extension appear on 2 lines and therefore filling up all 6. I should be able to do that with the

Hello everyone! Well i want to know, if there is a way to specify a physical nic (like eth0 or eth1) to a domU and how can i do it. The server has two nics, what i want to do is assign physical nic (eth0) to the dom0 and assign physical nic (eht1) to the domU. I appreciate your help. Regards Ivan ____________________________________________________________________________________ Be a

Hope someone can help. I have a situation where asterisk is sending a SIP CANCEL message before the Dial() timeout has hit. It doesn't always do it. Normally, we send an INVITE to the ITSP. They respond with a 100 Trying, then a 180 Ringing, or 183 Session Progress. It seems to be at this point that Asterisk starts the dial timer. Normally, when no more replies have been received by the dial

I've checked the samba code (sessetup) and found out that samba always send spnego packet when Extended Security capability is ON. (This can't be turned off/on ie. "use spnego = false") Does it mean I can "never" connect to smb server that doesn't support spnego if Extended Security is supported by server? Is my understanding correct?