similar to: TE205P

Hi all, I've setup a PBX in production environment last week but we have immediatly find out drop conversations and lot of errors (in asterisk logs) like: Apr 10 17:30:48 NOTICE[25154] chan_zap.c: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 2 My configuration is: Motherboard: SuperMicro P8SCT (Intel E7221 chipset) Hypertrading and APIC enabled CPU: P4 3GHz Digium TE205P

Trying to find my feet here. If I wanted to connect Asterisk to a PRI and throw in a T1 Adtran channel bank into the mix for fax machines would the following work? Connect PRI line from telco to Port 1 on the Digium Wildcard TE205P. Connect Adtran TA-624-T1 to Post 2 on the Digium Wildcard TE205P also, would I need a crossover to the channelbank or is it a patch lead like the connection to the

Hi ..., I've a TE205P card installed in my asterisk box.Port 1 of my card is connected to service provider.From port 2 I want to connect Avay Partner system. what type of cable I require to connect the partner system (straight/cross over). How the call routing from outside will be done to epbx. Thanks inadvance regards rudra -------------- next part -------------- An HTML attachment

Hi, I am having problems with an Asterisk with a Digium TE205P card. The issue is that the Ring Back Tone is noisy. I am making modem's calls and this noise influences on the initial negotiation protocol, so modems have to recall. My configuration is: Asterisk version: Asterisk 1.4.21.2 Linux version: CentOS release 5.2 (Final) Card: Digium TE205P

Hi i have a PRI connected to a TE205P. Actually, can i send and receive FAX through Asterisk using stable solutions? Or shall i connect an ATA to Asterisk and then a modem with Hylafax? -- /*************/ nik600 https://sourceforge.net/projects/ccmanager https://sourceforge.net/projects/nikstresser

Hey folks, I have a Digium TE205P working as a man in the middle: PRI line -------- Asterisk/TE205P -------- PBX The PBX is a Panasonic KX - TVP 100. Everything is working great except for one little issue. Asterisk isn't hanging up the PRI B channel when the PBX channel is hung up. I don't want to overload you with information but please ask if more is needed. I suspect I'm

Hi guys, Currently I just purchased the TE205P for the installation of my ISDN30 setup. I compiled, setup the card correctly I think. When I do the ztcfg -vvv it shows all 31 channels clear, with 30 bchannels using for voice ranging from 1-15, 17-31, and 16 is the dchannel. However, when I do a cat /proc/zaptel/1 I see only 24 channels configured, and then, when I do a cat /proc/zaptel/2 I see

I have a TE205P, jumpered for E1, added the missing wct4xxp-line to /etc/modprobe.d/zaptel, zaptel.conf is just span=1,1,0,ccs,hdb3,crc4,yellow span=2,2,0,ccs,hdb3,crc4,yellow bchan=1-15 dchan=16 bchan=17-31 bchan=32-46 dchan=47 bchan=48-62 Which, according to my reading of the documentation I could find, should be correct. ztcfg doesn't complain about anything, yet all I ever get is RED

hi i'm trying to configure a TE205P on asterisk@home i've edited /etc/sysconfig/zaptel adding this line: MODULES="$MODULES wct2xxp" now, when the system is loading, i can see that the wct2xxp module is loaded correctly but if i try the command: /usr/local/sbin/genzaptelconf i get: STOPPING ASTERISK STOPPING FOP SERVER Generating '/etc/zaptel.conf' Generating

Just a quick couple of questions for ya'll. 1) Does anyone know if VoicePulse Connect will be supporting dtmf tones? I have had a terrible time getting a hold of anyone over there, and I need this functionality before I can migrate to * completely. 2) Are there currently any problems with inbound DID's? Everything is setup properly in *, but I am not able to receive inbound calls,

I have recently installed Asterisk Now Beta 4 (32-bit) with three Digium cards - 2 Wildcards TE400P (one with 4 FXS modules and one with 4 FXO modules) and a TE205P dual E1/T1 card. The problem is with the TE205P and configuring the /etc/zaptel.conf and /etc/asterisk/zapata.conf files. I go in and add the required lines to configure the TE205P and restart Asterisk. All is fine until I reboot the

I've been working with Digium, but hopefully someone on-list has an idea... The card will transmit audio to the T1, but everything it receives is completely unintelligible static (in place of received audio only, not all the time). I've verified everything on Digium's troubleshooting checklist and they were unable to find anything when they logged in. zttest yields 100% for the

Hi there, We've got a problem connecting Asterisk with a TE205P to a TeleWest E1 ISDN line in the UK. We get a lot of "HDLC Bad FCS (8) on Primary D-channel" errors, and every so often the Primary D-channel goes down and all the calls got dropped. We've fully tested the card and made sure it's got its own IRQ. I was just wondering if anyone out there has

hi after some testing with A@H, i've decided to install my asterisk server on a slackware (because it's my favourite distro and it is still suggested here http://www.voip-info.org/wiki-Asterisk+Linux+Slackware) , so, i've installed the last 10.2 release, and i've recompiled the 2.6.15.4 kernel. then i've downloaded asterisk1.2.4 and zaptel1.2.4 i load module zaptel and

Hello, Digium uses the Dell PE 2850 for their testing. This site says that 3.3V PCI slot. http://www.voip-info.org/wiki/view/Asterisk+hardware We are planning on purchasing a Dell PE 2850 and putting a TE205P card on it. However, the needs a 5V PCI slot. Does Dell PE 2850 has a 5V PCI slot? A person in our group tried to call Dell's customer support but they do not seem to know.

I am having a issues with adding a analog card to my dell 2800. I already have a t1 card installed and running fine but when I install the analog card asterisk will not start (ztcfg fails). I have determined it is because of a IRQ problem and have decided to get a new server. Can anyone suggest a server grade setup that supports this? I would rather not buy a machine that will be unstable. I

Hi, I'd like to be able to log file transfers to/from an SSH server (both through scp and sftp-server). Perhaps I'm not looking in the right places, but I don't see a way of doing this in the current code. The "scponly" shell goes some (small) way towards doing this, however, it logs patterns rather than filenames in scp transfers. I have even less success with sftp. If

Hi all, I am trying to detect DTMF keys from a mobile when asterisk make an outgoing call to the mobile. The DTMF detection on incoming calls (also FROM mobiles) is working very well. The only problem is if asterisk called the phone... Nothing is detected. I am using a digium te205p with PMX/PSTN connection. Everything that I can find in forums are problems with dtmf detection on SIP. Any

Hi, thanks for your help. Your suggestion makes sense, however I think there should be some way for users to be able to change an expired password from login dialogue.  Actually I had a problem doing this previously with NT4 style Samba domain and never looked into a resolution.  Now that I've found Samba does AD style domain, I'm excited to use it in several customer locations.  Since I