similar to: zaptel_vldtmf

Well, I'm experiencing a similar problem with my setup... debian etch, asterisk 1.4.2, zaptel 1.4.1, ... I cannot find the chan_zap.so module file anywhere, tried recompiling with zaptel 1.4.0... no change... I tried 'make menuselect', and going to the channels-part, chan_zap is marked XXX -> dependencies missing: and this is the message for it, as an explanation. Zapata Telephony

Hi all. chan_zap not compiling, yes yes I know this sounds trivial but here me out... This morning I decided to upgrade to Asterisk 1.4.2 and Zaptel 1.4.1. I successfully installed zaptel 1.4.1 and the card is picked up and correctly configured. ztcfg shows the following: [root@zion root]# ztcfg -vv Zaptel Version: 1.4.1 Echo Canceller: MG2 Configuration ====================== Channel

I've downloaded: asterisk-1.4.1 zaptel-1.4.0 I've compiled and installed zaptel. When I go to install asterisk I do: ./configure make menuselect I then take a look under the codec selection menu and I see that codec_zap can not be compiled. *************************************

Hello: Have a TE110P laying around and decided to see if I could build a router around it. I've tried compiling several versions of zaptel .1.4.x with the same results. I checked the zaptel changelog and can't find anything about it no longer being supported (or that it ever was for that matter). ztcfg: Zaptel Configuration SPAN 1: CCS/HDB3 Build-out: 0 db (CSU)/0-133 feet (DSX-1)

lo there all, i recently upgraded to ubuntu 7 (fiesty fawn) and am having a problem with the install procedure for the zaptel modules. i did the make ; make install and it appeared to go ok, the wctdm module is in the list of lsmod after boot. so is the zaptel module. however when i do an asterisk -vvvv it gives me problem about chan_zap not being able to load. i googled and found some

Hi, am building the latest version of Asterisk (1.4.13) on a self-build Linux host (based on LFS-6.3). Version 1.4.12 built installed and worked fine. Last night I upgraded the kernel to 2.6.23 and rebuilt the zaptel driver package 1.4.5.1 against it. That seemed to build and install O.K. too. I dl'd the 1.4.13 source tarball and tried to build that: ./configure ran O.k. 'make

I decided to try 1.4 today. Zaptel builds, installs and seems to load correctly and Asterisk builds, installs and works but no Zap lines. When I typed "make menuselect" for Asterisk and went poking around I discovered that chan_zap is marked XXX and I can't figure out why that might be. Any suggestions? Ira

Hello everyone! I installed Asterisk following the instructions of the book "Asterisk: The Future of Telephony". (very nice book) However, I failed. I installed zaptel, libpri and asterisk (in this order). The Installation of Zaptel is successful and my TDM400P is correctly detected: # zttool Alarms Span OK Wildcard S400P

Hi all!! I have downloaded the asterisk from svn checkout http://svn.digium.com/svn/asterisk/trunk asterisk-trunk (is the asterisk 1.4 subversion). I also downloaded the patch for cellphone and make it work fine. Then I bought the tdm11b board to have phone connection in my computer. I installed the hardware for zapte and the libpri modules in my Mandriva 2007 and the lights of the pci card

Hi All, For the most part, the PBX works as it should. Occasionally people complain that they call and the PBX doesn't pick up. Other times it looks like the call is answered by Asterisk but I still hear ringing and I start listening to the IVR menu a few seconds into it. As for Asterisk not picking up, I see the following in the logs: [Mar 27 13:32:29] NOTICE[13197]: chan_zap.c:7071

---------- Forwarded message ---------- From: Juan Carlos Huerta <juancarloshuerta at gmail.com> Date: 07-abr-2009 13:41 Subject: Re: [asterisk-r2] MFCR2 With Unicall - can unicall affect zaptel commands? To: asterisk-r2 at lists.digium.com Please wirte to asterisk-users at lists.digium.com to get help about this problem. Juan Carlos ~ Lo que no te mata te fortalece ~ On Tue, Apr 7,

On 23 March 2016 at 09:35, Barnet Wagman wrote: | I am unable to install R on an up to date (i.e. apt upgraded) Ubuntu | 14.04 system. According to | https://cran.r-project.org/bin/linux/ubuntu/README (and many other sources), | R is available for this version of Ubuntu (which is a stable version). | | I currently have | | deb https://cran.cnr.berkeley.edu/bin/linux/ubuntu trusty/ | | in

Synaptic can show the origin of packages. The only thing I see from a backport is libcmanager0 I don't think this is relevant to R. Or is it. The only thing I've got installed from a ppa is mate (a desktop). I don't see anything related to mate that is related to R. FYI the ubunu I'm using came preinstalled from Dell (on a notebook; usually I install linux myself). On

It's a Dell XPS 13. Obviously I don't understand what's in libcmanager0. I wonder if I can safely replace it. I'm a bit uneasy about replacing things Dell installed. I gather there are some specialized drivers for the monitor on this system. On 03/23/2016 11:34 AM, Alex M wrote: > That could do it > http://packages.ubuntu.com/trusty-backports/libcgmanager0 > >

Hello! I'm trying to install R-3.0.1 on an Ubuntu machine (64 bit, version 13.04). I have uninstalled and installed several times, but to no avail. I keep getting errors about missing ldpaths, and installing packages does not work at all. Here is the information: erin@erin-Lenovo-IdeaPad-Y480:~$ sudo apt-get install r-base Reading package lists... Done Building dependency tree Reading

Hello Louis, ----------------------------------- # apt-get remove libldb1 ldb-tools Reading package lists... Done Building dependency tree Reading state information... Done The following packages were automatically installed and are no longer required: ? libtalloc2 libtdb1 libtevent0 Use 'apt autoremove' to remove them. The following packages will be REMOVED: ? ldb-tools libldb1 0

I installed Trixbox and a TDM400P with 2 FXO and 2 FXS ports and am having an annoying issue with the FXO ports. As soon as I plug either one into the phone line it's as though the line is disconnected i.e. get disconnected tone when trying to dial out, line is busy when dialling in. The CLI shows the following: trixbox1*CLI> zap show channel 4 Channel: 4 File Descriptor: 18 Span: 11*

Package: xcp-xapi Version: 1.3.2-6 Severity: important Looks like on Wheezy, /etc/default/xen is not created by xen-utils-common. Since xcp-xapi depends on its existence and further declaration of the toolstack in it, it should take extra care to ensure that it is present. root at debian:~# aptitude install xcp-xapi The following NEW packages will be installed: blktap-dkms{a} blktap-utils{a}

That could do it http://packages.ubuntu.com/trusty-backports/libcgmanager0 Seems to be libc related, which is a pretty core library to much of the whole system. Hmm, which model Dell? We just got a Dell 5000 series with Ubuntu, I have not checked with my boss if there was R installation issues. Thanks, Alex On 03/23/2016 11:22 AM, Barnet Wagman wrote: > Synaptic can show the origin of

Few days back I installed Asterisk 1.4.2 with Zaptel 1.4.0. All SIP accounts were working fine, today I tried to install a fxs Sangoma A200 card and got the following error. [Apr 12 01:15:17] WARNING[31018]: channel.c:3024 ast_request: No channel type registered for 'Zap' [Apr 12 01:15:17] WARNING[31018]: app_dial.c:1090 dial_exec_full: Unable to create channel of type 'Zap'