similar to: RTP no sound on asterisk

I am using asterisk 1.4.18 with a polycom phone. sip.conf has: [532] type=friend username=532 secret=XXX dtmfmode=RFC2833 host=dynamic context=smvoice-sip callerid=532 qualify=no nat=no disallow=all allow=ulaw allow=alaw allow=gsm canreinvite=no I call into the dialplan and try to play demo-congrats and I hear nothing. Firewall is disabled. Everything is on the 192.168.1.X network for this

Hi all, i have a little problem to understand this warning message, it's annoying and it cause a lot of spurious in the log files. Im working with this scenario: a sip outgoing trunk (Trunk-out) that support only ulaw and all calls are always routed to this. a list of sip UAs that potentially can use any codec apart g729/g723. I setup the asterisk to do as mediaproxy so directmedia=no and

With asterisk 1.8.7.0 has been running ok for months. Now, this morning, it's crashing. I can restart it, but it crashes after 10+ minutes. It dies like this -- Executing [s at macro-stdexten:2] Dial("SIP/teliax-00000019", "SIP/176,18,rtT") in new stack == Using UDPTL TOS bits 184 == Using UDPTL CoS mark 5 == Using SIP RTP TOS bits 184 == Using SIP RTP

Hello, I have problem to make SIP calls, i have asterisk + PC InterP4 + Digium TDM400P here is the content of the sip.conf: [SIP_PROVIDER] type=peer fromuser=testcomclient username=testcomclient secret=testr host=IP_SIP_PROVIDER ;dtmfmode=rfc2833 context=interne canreinvite=no ;allerid=Beer disallow=all allow=ulaw allow=gsm allow=g723.1 ; Asterisk only

I have a system running CVS HEAD 6/30/2004. We've only been using it for PSTN to channel bank handsets, but have decided to add sip phones into the mix. Now I have quite a few systems running sip phones just fine as well as some running both sip and analog via channel banks or tdm cards. When we tried to set up some sip extensions (they are behind nats, we are using xten light, and have

Starting with Asterisk 13.1 we are seeing this WARNING messages a lot in our logs and console: WARNING[25164][C-0004865e]: chan_sip.c:7364 sip_write: Can't send 10 type frames with SIP write) We found that line in function "sip_write" inside "chan_sip.c". In our previous version (11.2.1) we did not see those messages being printed (same verbosity level). We compared

To me it's a error if I can't complete calls using the ATA configured to use the g726 codec. I just tried it usign a sipura SPA-2000 (preferred codec: G726-32) and I received NOTICES and WARNINGS, but I can't complete a call. On a zap channel: -- Executing Dial("SIP/2007-e4d8", "Zap/1/2217008") in new stack -- Called 1/2217008 -- Zap/1-1 answered

Under 1.4.35 I get this message printed MANY times [May 3 21:41:21] WARNING[21567] chan_sip.c: Asked to transmit frame type 4, while native formats is 0x1000 (g722)(4096) read/write = 0x1000 (g722)(4096)/0x1000 (g722)(4096) [May 3 21:41:21] WARNING[21567] chan_sip.c: Asked to transmit frame type 4, while native formats is 0x1000 (g722)(4096) read/write = 0x1000 (g722)(4096)/0x1000

Hi, For some time now, I've been fighting with RxFax and Asterisk. I had it working for some time, however, for some reason it just stopped working, I guess someone updated Asterisk or something, don't know exactly. At the moment I keep getting errors while entering the RxFax stage of a call. But due to the fact RxFax does not contain any code to directly interact with an RTP stream,

Hi everyone, I have an issue which is kind of a catch 22 situation. I had outgoing calls to my new PSTN provider working perfectly. Then I started focussing on incoming calls. It seems that I can solve an error which gets my incoming calls working but that in turns means my outgoing calls don't work. - Strange. Anyhow I was getting an error: Process_sdp: No compatible codecs! And from

Hi All, I have Asterisk 1.2.9.1 sending SIP calls to a Cisco 2620XM Router with a PRI card in it, handing off to a PBX and vise verse. Calls in and out are working fine except for DTMF from Asterisk to the 2600. DTMF from the 2600 to Asterisk is fine. Here are the Asterisk console warnings I get when I send DTMF from Asterisk to the 2600: == Forcing Marker bit, because SSRC has changed Jun

On 6/26/07, JR Richardson <jmr.richardson at gmail.com> wrote: > Hi All, > > I have Asterisk 1.2.9.1 sending SIP calls to a Cisco 2620XM Router > with a PRI card in it, handing off to a PBX and vise verse. Calls in > and out are working fine except for DTMF from Asterisk to the 2600. > DTMF from the 2600 to Asterisk is fine. > > Here are the Asterisk console warnings

Hi all, I did not get this error in Asterisk 1.2.5 release. I am testing on Asterisk SVN-trunk-r15187 to avail the PARKEDAT variable. - I park the call using ParkAndAnnounce - plays moh. - accept the call using ParkedCall The following errors are coming on the console and there is oneway audio - no audio after Music-On-Hold at caller's side. Please advice. I am testing using cisco 7902

We are getting the following on 1.8.3 and 1.8.4-rc2, HELP! Why is Asterisk unable to transcode to/from ulaw and g722? [2011-04-21 09:51:34] WARNING[22067]: chan_sip.c:6064 sip_write: Asked to transmit frame type ulaw, while native formats is 0x1000 (g722) read/write = 0x1000 (g722)/0x1000 (g722) [2011-04-21 09:51:34] WARNING[22067]: chan_sip.c:6064 sip_write: Asked to transmit frame type ulaw,

I have a ATA 186 with SIP firmware 3.1 when I changed the configurations to use the g.726 codec I received many erros and the calls doesn't work. I changed the fields: - LBRCodec: 6 <- the code for g.726 - TXCodec: 6 - RxCodec: 6 The errors: Jul 9 13:15:37 NOTICE[1192491824]: rtp.c:500 ast_rtp_read: Unable to calculate samples for format G726 Jul 9 13:15:37 NOTICE[1192491824]:

Good afternoon list. I'm experiencing a problem with my SIP channel's. When I have an external connection for one of my SIP carrier's, I can listen to the client and the client listens to me normally. The problem is when I will transfer this connection, the call is mute for the extension I have transfered. Only the client hears normally. In the console of Asterisk generates the

Hi Guys, I have a the following issue when I ma trying to place a call through my voip provider, I am using an asterisk 1.2.21.1, do you have an idea what could fix this issue (as you can see when the other party answered, the call get dropped because of probably sip incompatibility) Nov 12 14:31:30 WARNING[21432]: chan_sip.c:2587 sip_write: Asked to transmit frame type 256, while native formats

Hi there I have two different asterisk systems (both 1.4) whose dtmf tones are not being picked up by a particular conference system users are dialling into. I can call myself with the phones and hear the tones, but I am guessing perhaps they are too short or somehow different. I have looked and looked but can't nail down the reason. I don't believe this is a general issue, rather some

Hi list! I have 4 numbers on my Asterisk 1.8. 3 work perfectly, the 4.th not. I'm not sure, when it finish to work, since a month ago it runs without any problem... Well, if I will be called on this number I can't hear anything and in Asterisk I see these: [Jul 15 18:59:55] WARNING[8752]: channel.c:5060 ast_write: Codec mismatch on channel SIP/00493514977290-000001d1 setting write format

Hi, I have an issue which is kind of a catch 22 situation. I had outgoing calls to my new PSTN provider working perfectly. Then I started focussing on incoming calls. It seems that I can solve an error which gets my incoming calls working but that in turns means my outgoing calls don't work. - Strange Anyhow I was getting an error: Process_sdp: No compatible codecs! And from the SIP