similar to: Sync Problem (astribank)

I have a pretty large setup on one of my customers. Digium TE420B (with echo cancelling module), 3 Xorcom Astribanks with 32 FXS each and 1 Xorcom Astribank with 16 FXO. These FXO ports are NOT used for fax/data transmission, as they are connected to cell phones. Not really related to the issue, but there are also 250 SIP phones. The problem is that fax and dial-up connections are really

I have recently updated from Centos/*1.2 to Ubuntu Server and FreePBX 2.8.0.2. We have an Astribank with 4 T1 ports and 16 FXS ports. After updating, we had it working for a while with one NT PRI and one TE PRI and, in the process of trying to configure another PRI, I ran into a couple problems. (1) As my configuration changes didn't seem to affect the Astribank, I power-cycled it. I

Hello, I'm in the process of building an Asterisk machine and need 5 or 6 BRI-Channels. I was looking for the beroNet and Junghans cards and stumbled upon the Xorcom Astribank xBRI products. Has anybody tried out the Astribank xBRI-Channel Banks? Are they production ready or should I go with a beroNet BN8S0 or JUNGHANNS.NET octoBRI ISDN? Thanks in advance, Lars -- We don't like their

Hi, all My Asterisk uses a Digium TE120Pand I would like to add an Astribank zaptel_hardware sees is, but I cannot get it working pbx:~# zaptel_hardware Argument "IRQ" isn't numeric in numeric comparison (<=>) at /usr/local/share/perl/5.8.8/Zaptel/Span.pm line 114. usb:005/002 xpp_usb- e4e4:1131 Astribank-8/16 USB-firmware pci:0000:04:00.0 wcte12xp+

Hello Mailinglist, we have a Xorcom Astribank which is installed at our client and working since 10/2008. Suddenly last week there where odd behaviors, no calls going through (it is used to route calls to GSM Gateways). Upon testing (reinitialization of the complete gear) it turned out that one call get's through and then nothing more. I have nothing in the logs, indicating that Asterisk

I am running Asterisk on Ubuntu 2.6.32-25-server with asterisk 1.6.2.5-0ubuntu1 and dahdi 2.2.1-0ubuntu2. The machine has a passive HCF-based PCI ISDN card and an Astribank 8 attached. The ISDN card works fine. root at servaction:~# lsusb Bus 001 Device 002: ID 04b4:8613 Cypress Semiconductor Corp. CY7C68013 EZ-USB FX2 USB 2.0 Development Kit root at servaction:/usr/share/dahdi# ./xpp_fxloader

Hi all, I'm interested in buy a Astribank-32 but i never heard about detection of far-end disconnection. Does anyone have some experience about that functionality in this hardware ? Thanks in Advance, Gleidson Antonio Henriques

Hi, I have a Xorcom Astribank connected to my Asterisk server. In one of the Astribanks FXO port I have a Celular Interface Module. My problem is the Astribank is receiving a early answer from the module, which doesn't happen with a ATA connected to the same module. This is causing some trouble with my billing system. I already tried the answeronpolarityswitch option, what else can I do ?

Hi all... I'm sorry for repeating my message. I have a problem with caller id on my asterisk server with xorcom astribank. here is my configuration : centos-5, asterisk 1.6.2.1, dahdi-linux-complete-2.2.1, libpri-1.4.10.2 ibm X-3200 series, xorcom astribank (16fxo, 8fxs), 16 line telco (hunting) everything fine until I try to feed my app with caller id. here is the log : --

Hi guys, This has been bugging me for days and I can't figure out what's happening. Using the same channel on DAHDI, I can't make a call after previous one being hung up by remote side. However, it works like it should if my end hangs up the call. To make things interesting, DAHDI, or astribank rather, seems to "reset" itself after receiving an incoming call on that DAHDI

Hi Guys, An 8 channel Astribank is connected to Trixbox 2.8 and I ran freepbx-module-zapauto but I get the following when running these commands and can't make calls out: [Trixbox]# dahdi_genconf xpporder /usr/sbin/dahdi_genconf: warning - OLD DRIVER: missing '/sys/bus/xpds/devices/00:0:0/timing_priority'. Fall back to /proc pbx*CLI> dahdi show channels Chan Extension Context

Hello, I'm writing here hoping to have a hint from Asterisk/Digium packager maintainer, Jason Parker (of course that any other's opinion is welcomed). We have installed an asterisk machine using Asterisk and Digium repos. Unfortunately we have found that an Astribank could not be connected due to the lack of the firmware files May 18 14:19:22 tenora1 kernel: usb 1-6: new high speed USB

I have a server with 8 Xorcom Astribank, they're connected to the server via a USB hub, my problem is: when a reboot the server the ID of the Channel Bank changes, cousing a big mess on my server. Anybody know how can I solve this ? Best regards, -- Guilherme Loch G?es Visite nossa loja virtual: http://www.shopvoip.com.br Not?cias e F?rum sobre VoIP com software livre:

Hi All Just a quick check on the best way to ensure multiple cards/devices load in the correct order. Asterisk 1.8 with Sangoma A101 had no problems until we introduced an Astribank. root at pabx377:/etc/asterisk# dahdi_hardware -v usb:001/004 xpp_usb+ e4e4:1162 Astribank-modular FPGA-firmware LABEL=[usb:X1060395] CONNECTOR=@usb-0000:00:1d.7-3 XBUS-00/XPD-00:

Hello, I've one astribank with 8 FXO unit and 8 pstn lines connected to the astribank. When I receive calls on my ipphone I get always Unknown callerid. It's is possible to receive the callerid from the lines on the astribank unit? This is my config: [channels] language=es context=from-zaptel signalling=fxs_ks ;rxwink=300 usecallerid=yes callerid=asreceived ;cidsignalling=bell

I have a strange problem with overlap dialing. I installed an asterisk server between a Siemens HiCom PBX and our telephony provider. Everything is working fine except some strange problems with the dialing of the fax (connected to the HiCom PBX). It seems to me that if dialing takes too long Asterisk just hangs up the channel without recognizing that the fax machine is still dialing: (Fax gets

Hi, I have upgraded an Asterisk installation with a Xorcom BRI Astribank that was working under Ubuntu 8.04 to Ubuntu 9.10 and the device is no longer initialized. When I reload the udev rules, I see that the rules seems to be correctly loaded: udevd[452]: reading '/etc/udev/rules.d/40-xpp.rules' as rules file However, these rules do not seem to be triggered: # udevadm trigger

H all... I have an Astribank (8FXS/16FXO), IBM X3200 M2, Asterisk-1.6.2.1, dahdi-linux-complete-2.2.1, libpri-1.4.10.2, centos-5.4 final. My problem is, every time i unplug the astribank power supply, and reconnect it, astribank cannot work again (lsusb result is 11x0)... but, after reinstall the asterisk and dahdi, astribank will detected (lsusb result is 11x2)... any suggestion? Regard,

Hi all... I have a problem with caller id on my asterisk server. here is my configuration : centos-5, asterisk 1.6.2.1, dahdi-linux-complete-2.2.1, libpri-1.4.10.2 ibm X-3200 series, xorcom astribank (16fxo, 8fxs), 16 line telco (hunting) everything fine until I try to feed my app with caller id. My extensions.conf : [incoming1] exten =>

Hello List, it is a very long time since I wrote here.... It has been still in Zaptel times.... Today I am run into a related problem: I can't get a DAHDI setup to work 100%. I am configuring an Astribank XR00013 (BRI, two ISDN ports). At some degree the installation (latest DAHDI drivers, Asterisk 1.6.0.18 on Centos 5.x) works. I can get incoming calls to the dialplan context that is