similar to: Digium B410P and 8 ports connectivity

Checkout Beronet ISDN cards and Berofix Gateway (appliance or pci card) Personally for my last installation I chose Berofix card which is rock solid and reliable, yet easily configurable. With berofix you don't need telephony drivers on the host system, the isdn card is detected as a NIC and all configuration is done using a web interface. Then you configure FreePBX a new trunk to use the

Hi. Using Asterisk 1.4.13 running on Ubuntu 7.04 with Intel CPU: 1) Not being able to build mISDN on Ubuntu using "make b410p" I have used mISDN-1_1_7 which seems to work ok. QUESTION: Should I expect this version of mISDN to work ok with these cards? Or is there a way to build using "make b410P" on Ubuntu? (make force does not help at all) 2) In some of our installations

Hi, please whoever has some expertise in choice of BRI ISDN cards, please restore my faith in community support :) (on private email I can probably explain more than fits for a public forum) Most I'd like to ask is about what to choose, out of what is available... My locality is United Kingdom, lines from British Telecom (BT), but any advice / pointers (I googled around already) are

Hi. Using Asterisk 1.4.13 running on Ubuntu 7.04 with Intel CPU: 1) Is it possible/supported to install two or more B410P Digium cards in one computer (single Asterisk installation)? 2) Do they need to be hard-wired together with a PCM cable like I've seen explained in some beronet manuals (although that was specifically geared towards their cards, I must say)? Thank you for your time and

hello list, i have a problem regarding the synchronisity (clock source) when using multiple cards. e.g. when having connected one PRI port of our TE410P to the telco, i need to have the analog card like the TDM400P or a B410P synchronous to the clock of our telco provider. otherwise faxing on the analog cards does not work or i get cracking noise or even hangups on my BRI lines, due to bit slips.

Hello, I'm in the process of building an Asterisk machine and need 5 or 6 BRI-Channels. I was looking for the beroNet and Junghans cards and stumbled upon the Xorcom Astribank xBRI products. Has anybody tried out the Astribank xBRI-Channel Banks? Are they production ready or should I go with a beroNet BN8S0 or JUNGHANNS.NET octoBRI ISDN? Thanks in advance, Lars -- We don't like their

The DAHDI docs actually include the 'steps' that used to be in Zaptel's 'make b410p'. These steps involve downloading and compiling mISDN. Why re-invent the wheel? Just a thought :-). As for the 100ohm termination bit - it's simply changing a couple of dip switches on the b410p card (as described in the manual). Andy -----Original Message----- From:

Hi, My set up is : Asterisk with B410P in NT mode <-------------cat5 straight cable ----------------> Another PBX in TE mode Is the 100 Ohm terminator you can find on B410P boards, necessary when connecting in NT mode to another PBX (set in TE mode) ? Cheers -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi list, we have a dual Xeon server with 2GB RAM running Debian Etch 2.6.18.4-686 kernel. The server has 2 B410P cards plugged in. No other card. We installed Asterisk 1.4 trunk with zaptel trunk, ran make b410p, the install mISDN1.1.0 (for bug 9064) configure and compile Asterisk with chan_misdn, all is fine. In misdn-init.conf we have added option=1,master_clock. Asterisk is up and

Hi, 1. Has someone met any success at all, connecting a Digium B410P to a Patton Smartnode 4638 (with latest 5.3 firmware) ? 2. If positive, then, which signalling was used on both sides ? My project's goal is use a Patton Smartnode 4638 to act as telco BRI lines, from a B410P-enabled asterisk box. In my testings, I can see channel is respectively up (with patton web server status page)

Hi, I've been able to make make install the Zaptel drivers (1.2). I'm using a b410p so I executed the following command make b410p. I tried this on multiple machines, but it always failes: root@asterisk:/usr/src/zaptel-1.2.11# make b410p [ -f misdn-b410p.tar.bz ] || wget ftp://ftp.digium.com/pub/zaptel/b410p/misdn-b410p.tar.gz --23:59:54--

Hi list, Is Digium Wildcard B410P compatible with Asterisk 1.2 / 1.4 (zaptel of course) directly out of the box, or do I need things like bristuff? http://www.digium.com/en/products/hardware/b410p.php Best regards, Henrik Woffinden

We have recently purchased a B410P Digium 4* ISDN-2 card with hardware EC. On the same server, I also have a regular Digium 4-channel PSTN-card (TDM410P ?), used to interface to some analog devices, a.o. 2 fax machines. For faxing, EC needs to be off (or so I understand from the archives). How can I switch EC off for an ISDN B-channel if a fax is coming in? Z.

Hi, My setup is: IPPhone1 --- Asterisk1 with B410P ---- Patton 4638 --- Asterisk2 --- IPPhone2 I want to evaluate Asterisk1 in TE/PtmP mode. So, Patton box is configured in NT/PtmP (with 3 BRI links between both systems). Anyway, asterisk -rx "pri show spans" keeps replying : PRI span 1/0: Provisioned, Down, Active PRI span 2/0: Provisioned, Down, Active PRI span 3/0: Provisioned,

Hi all! Sorry for my poor english, i'm italian. I installed Digium B410P on my asterisk server. I followed the official installation instructions found on digium site. These instruction, in my opinion, are not clear, so i tried with other ways (found on the trixbox site). I found this: http://www.trixbox.org/forums/trixbox-forums/trunks/howto-install-script-digium-b410p Now i can receive

Hi, I'd like to know what's the most "popular" method for automatic fax/voice detection for incoming calls on mISDN cards such as the B410P (hfcmulti). I'm running: kernel 2.6.17 misdn 1.1.3 asterisk 1.4.21.2 B410P card I'm using iaxmodem and hylafax with asterisk (the setup works for zap channels). I've used the following options in /etc/asterisk/misdn.conf:

Hi, Until now I've been using my Digium B410P cards with misdn 1.0.x. I would like to upgrade my systems and am now wondering which is the "best" route to take: - use the latest release of misdn v1 - upgrade to the latest "stable" kernel and use the built-in misdn v2 - use misdn v2 as a seperate package (disable misdn in the kernel) - use dahdi's support for misdn

Hi, I've read that the new dahdi channel supporting B410P doesn't support PtmP when in NT mode. Does it support PtmP when in TE mode ? Cheers -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20081209/f422b5d0/attachment.htm

Hi all, I am having trouble setting the signalling method for the B410P using DAHDI. Asterisk complains that it has never heard of 'bri_cpe' or 'bri_net' - but it doesn't mind having 'pri_cpe' etc. ERROR[4294]: chan_dahdi.c:11327 process_dahdi: Unknown signalling method 'bri_net' Dahdi - dahdi-linux-complete-2.1.0.4+2.1.0.2 Asterisk - 1.4.23.1 Libpri - 1.4.9

Hi, Which echo-canceler shall I pick for Digium B410P ? Is HPEC relevant ? Reading from its datasheet, it seems related to analog cards. Regards -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20080221/ed5c5d6f/attachment.htm