similar to: Zaptel 1.4.8 breaks tor2 support on CentOS 5.1? (kernel panic)

I just received my dev kit and installed the hardware. I followed the directions Digium sends out to the letter and when I ran modprobe tor2 I got the following error: /lib/modules/2.4.18-19.7.x/misc/tor2.o: init_module: No such device Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters. You may find more information in syslog or the

Hi list, I have a asterisk box with an E400P that was running ok until last week. The machine just stop responding and after a reboot, the module (tor2) doesn't load anymore. anyone could help? regards Eduardo modprobe returns this: asterix:~# modprobe tor2 Zapata Telephony Interface Registered on major 196 Detected Tormenta 2 Quad T1/PRI or E1/PRA at 0xfe121800/0xfe121000 irq 7

We use dual Athlon machines with up to three T400P 4-span T1 cards. If I have more than one stick of memory (2 1GB modules or 2 512K modules, each identical), I'm getting a panic soon after I modprobe the tor2 driver. I just loaded the latest from CVS and I'm still getting the panics, which look in part like: Apr 16 14:42:28 test71 kernel: wait_on_irq, CPU 0: Apr 16 14:42:44 test71

Ok. I just got a TDM10B and it is in with my X100P. So as it says in the provided instructions, I used the command modprobe tor2 I get an error message saying that there is no such device. My zaptel.conf looks like this: fxsks=1 fxoks=2 So I load the X100P first. (modprobe wcfxo) Then I load the TDM10B (modprobe tor2) Then I'm told that the device doesn't exist. Please help

i have error in install module of tor2. but it compile good. what happen ? ivr2:/usr/src/zaptel # make clean; make install rm -f torisatool makefw tor2fw.h rm -f zttool rm -f *.o ztcfg tzdriver sethdlc rm -f zonedata.lo tonezone.lo libtonezone.so.1.0 *.lo rm -f gendigits tones.h rm -f libtonezone* rm -f tor2ee rm -f core cc -I. -O4 -g -Wall -DBUILDING_TONEZONE -DSTANDALONE_ZAPATA -c -o

Hi, We are trying to validate Asterisk as a media gateway PRI <-> SIP with two T400P (8 T1s) per box. The first experience with BOX1 (Compaq, 2.53 GHz, 1 Gb RAM) and just one T400P was encouraging - on the load test with 3 T1s worth of calls we had on average 75% idle CPU. Not so with BOX2 (Dell, single 2.6 GHz Xeon, 1 Gb RAM, 2 T400P) and BOX3 (Dell, dual 2.6 GHz Xeon, 2 Gb RAM, 2 T400P,

Greetings, I have a quad port Tormenta 2 PCI card (uses the tor2 driver), which I have been successfully using for some time on an older, power-hungry Intel machine. I recently moved it to a newer machine with an Intel Atom D510 CPU in an effort to save on energy costs, but I cannot seem to get it to work there. Both machines are running Ubuntu 13.10 x64, with DAHDI support coming from the

Hello guys! I hope you bare with yet another newbie on the list! :-) I am trying to setup an asterisk installation in between a Siemens HiPath 3800 and my local carrier (Telefonica/Brazil). Both running R2. ISDN is not an option on the carrier. :-( I could apparently setup both E1s just fine according to zttool (both OK with no alarms) but, and this is where it starts to get

Hi all. I've been trying to build some new systems, and no matter what I do, if I load the zaptel and tor2 drivers, the system panics within an hour, even with no traffic. These systems are using dual Athlon MP 2800 chips with one, two, or three T400P boards and 2 GB of system memory. I'm currently using Fedora Core 1, but I also went back to our old reliable Red Hat 7.3 and the systems

Followed the "instructions" on voip-info.org regardinging fedora FC2, making Zaptel seems to work fine, however when I modprobe I get this. It looks like a version mismatch somehow. Ideas? If this ooc, sorry first post here :-) modprobe tor2 WARNING: Error inserting zaptel (/lib/modules/2.6.5-1.358smp/misc/zaptel.ko): Invalid module format WARNING: Error inserting zaptel

Hi All, Newby with problem when attempting to make Zaptel on Red Hat linux 9.0. I have seached Google, VoIP forums etc and cannot resolve issue. (Red Hat 9.0) Linux version 2.4.20-31.9 (bhcompile@daffy.perf.redhat.com) (gcc version 3.2.2 20030222 (Red Hat Linux 3.2.2-5)) #1 Tue Apr 13 18:04:23 EDT 2004 All Packages installed per: http://www.voip-info.org/wiki-Asterisk+redhat9+packages Per

Hi, I have just begun working with TDMoE running between 2 fiber nics the dynamic span works great. In my main asterisk box's startup file I just 'modprobe tor2', then start asterisk. The zaptel, ztdynamic & ztd-eth modules all load by themselves when tor2 is loaded. If I stop asterisk then 'modprobe -r tor2' the tor2 module is removed but the other three remain. If I

Hi All, I'm having a bit of a time getting my Tormenta 2 card to actually be seen by the system. Whenever I modprobe, the kernel spits out the following (in addition to the "insmod tor2 failed" messages): Invalid Xilinx 8 bit Base resource Registered Tormenta2 PCI Of course, the module says that its registered a Tormenta2 card, but it unloads the driver and frees related

Hey all, ? I'm trying to get an E400P and 2 X100Ps working together in the one box and don't seem to be having much luck. ? I can get the two different types of boards working separately, but not together.? I've made calls on both the X100P and have seen sync and correct signalling on the E400P.? But when I try to enable to configs together I get the following: ? modprobe wcfxo

Another nibbage question: modprobe tor2 -v install /sbin/modprobe --ignore-install tor2 && /sbin/ztcfg insmod /lib/modules/2.6.5-1.358smp/misc/tor2.ko ZT_SPANCONFIG failed on span 1: No such device or address (6) FATAL: Error running install command for tor2 dmesg states that the module is registered however. Am I doing something seriously wrong? I have my zaptel.conf configured as

Hi! I have fresh installation of Fedora (Core 1) RedHat Linux-2.4.22-1.2115.nptl The kernel source is in place /usr/src/linux-2.4.22-1.2115.nptl The config file for the kernel is in place /boot/config-2.4.22-1.2115.nptl As per zaptel instruction, i first created the kernel config file as follows: # cd /usr/src/linux-2.4.22-1.2115.nptl; make menuconfig (in the menu config window) I loaded the

Trying to update to the latest cvs, but Asterisk complained that zaptel was too old. Updating zaptel gives me this during the make. Any ideas, the searches and Wiki gives me no hints. cc -I. -O4 -g -Wall -DBUILDING_TONEZONE -DSTANDALONE_ZAPATA -c -o gendigits.o gendigits.c cc -o gendigits gendigits.o -lm ./gendigits gcc -I/usr/src/linux-2.4/include -O6 -DMODULE -D__KERNEL__ -DEXPORT_SYMTAB

So I went to go compile the Zaptel library from the HEAD CVS and I get some really really odd errors which don't make any sense. I've attached the console output ... any idea why this is going on and how to fix this? Thanks, Sam Bacsa ---------------- SNIP -------------------- [root@pbx zaptel]# make gcc -I/usr/src/linux-2.4/include -O6 -DMODULE -D__KERNEL__ -DEXPORT_SYMTAB

I fixed this error on mine by creating a symbolic link in /usr/src with: ln -s linux-2.4.21-15.0.3.EL linux-2.4 of course using your particular flavor of redhat kernel instead of linux-2.4.21-15.0.3.EL. > -----Original Message----- > From: asterisk-users-admin@lists.digium.com > [mailto:asterisk-users-admin@lists.digium.com] On Behalf Of > Ricardo Maia Martins dos Santos >

Hi! I have just bought the X100P and TDM400P cards to install on my computer to implement the PBX. I also downloaded the newest softwares asterisk_ver0.5.0, libpri_ver0.4.0, and zaptel_ver0.7.0) to install on my computer (Red Hat Linux 8.0). All packages are compiled well. When I use "modprobe" to load drivers (modprobe zaptel, modprobe wcfxo, modprobe wcfxs), the first two (zaptel,