similar to: Jabber and Asterisk?

I have sent a few emails over the past couple of days that simply have not arrived on the list (or so it seems). Is anyone else encountering this ? Julian

Hello Previous context :- After Looking up sip and IAX2 that require configuration at router level which may cause some problems like connection break etc... so i left them ......... and start wondering if there is some thing that dont require configuration at router layer. The task to accomplish to make and recieve calls from outside local network using any protocol whose soft phones are

Wow. My message made it to the list after more than 3 hours. Philipp -- amooma GmbH - Bachstr. 126 - 56566 Neuwied - http://www.amooma.de Let's use IT to solve problems and not to create new ones. Asterisk? -> http://www.das-asterisk-buch.de Gesch?ftsf?hrer: Stefan Wintermeyer Handelsregister: Neuwied B 14998

Hi, Do you if a DECT-GAP (or DECT-CAP) compliant handset MUST or MAY support roaming and handover and are these functions transparent for handset (then, these functions are implemented in DECT base stations) ? Regards -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20080110/4254f602/attachment.htm

All, I have AAH 1.0 installed using Digium TDM04B and Grandstream GXP2000 phones. All seems well other than the phones have to be reset up to 5 times per day. It is like they lose thier ip connection or maybe thier SIP connection. Has anyone else experienced this issue? I have the phones set for static IP addresses and that doesnt seem to help either. Any help would be greatly

Hello ! I would like to get working a Fritz PCI card using chan_misdn operating in ptp mode. Afer compiling mISDN into the kernel and building chan_misdn Asterisk stops loading with : [chan_misdn.so] => (Channel driver for mISDN Support (Bri/Pri)) == Parsing '/etc/asterisk/misdn.conf': Found UnLocking config_mutex == Registered channel type 'mISDN' (This driver enables

Hi everybody :) I am a new member here and hope that someone gives me a hint for my problem: Let's say I am at work and my SIP phone (KPhone in my case) is connected to my private Asterisk. I want to call my wife at home so her SIP phone rings. She does not pick up the phone (maybe she is somewhere in the house and has to run to the phone) so after 15 seconds her cell phone should ring.

Does anyone have a good resource to learn how to program the soft and hard buttons on a Cisco 7940 or 7960 phone? Using SIP Firmware...thanks. -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20060303/e5e63834/attachment.htm

I have an asterisk box and SIP / IAX2 phones. To call out, users have to add 0 (zero) before a real telephone number. That means, that if they want to call someone that has a number 123456, they have to call 0-123456. Simple, right? This has a serious drawback though - when someone calls us from the number 123456, we see the callerID 123456, and we're unable to use the callback/redial

Anyone had any experience with an Asterisk server as a VMWare virtual machine?

ONLY ON MONDAY! Well it used to work - calls between my aaln's that is. I moved from debain to redhat (same conf. files for asterisk) and this is what I get.. looks like several errors. errors I never got before. Also asterisk isn't observing the digits as I dial them like it used to however it still trys to route the call when I'm finished dialing. Anyone with a though on this?

I've added lines like this: speeddial = 123,test speeddial = 260,Bob in the [device] section for my 7921, but the speed dials do NOT appear on the menu (click right from the main screen). Am I missing something obvious here? Thanks MD -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hello, Here is a breakdown of the issue I am experiencing. I have three remote employees, in various states, who have Polycom 501 phones. They are unable to receive incoming calls after a few minutes of the phones being plugged in. They work immediately after being plugged in, but they lose the ability shortly thereafter. They can always make outbound calls, but only to real phone numbers, not

Hi, Anyone here using sipgate.de ? It worked for months, but for a couple of days now I'm unable to register with them. My account is ok, because I can login to the website. Asterisk keeps showing me: Feb 25 23:50:18 NOTICE[5144]: chan_sip.c:5269 sip_reg_timeout: -- Registration for 'XXXXX@sipgate.de' timed out, trying again (Attempt #n) I looked at the sip debug stuff, and all I

I have a call center where we're looking at converting it from a traditional PBX w/ digital phone "agent" sets (keyless phones) that have headsets to a SIP based environment. I am having trouble finding anything on the market that resembles this in the VoIP world. For reference, we're currently using Inter-Tel Agent Sets, which are basically a digital phone with out any keypad,

Hello @List, i'm using a Cisco 7970 / 7914 phone with Asterisk 1.4 & sccp part of my sccp.conf type = 7914 (Cisco 7970 with 7914 phone extension) autologin = 117 description = Test speeddial = 10,Test (10),10@mycompany my speeddial line is for internal call howto call a external number eg. +xx467584933 ?? i want to press a button and call directly out thank you greetings, Daniel

Hello guys, The so expected 2.0 release of Idefisk 2.0 softphone is a fact. Idefisk and Zoiper became one - Zoiper 2.06. Here are some of the features: SIP and IAX, TCP, TLS support, Multi-language support, Automatic provisioning (XML), URL handling, Outlook Integration, Native conferencing, API, Changeable number of lines.... You could read the complete Press Release here:

After upgrading from 1.2.25 to 1.2.26 i noticed that IAX -> IAX calls always result in Asterisk just exiting without any message. Asterisk also seems to die when using a TDM400 with 2 FXO modules, placing 2 outgoing calls on both lines as Zap/g2 and then trying to make a 3rd call. Went back to 1.2.25 for the moment

What on earth is going on with the list?!?! Some of my messages never make it... then days later I get something like this back: Final-Recipient: rfc822; asterisk-users@lists.digium.com Action: failed Status: 5.0.0 Diagnostic-Code: X-Postfix; mail forwarding loop for asterisk-users@lists.digium.com

Bristuff has been updated; http://www.junghanns.net/downloads/bristuff-0.3.0-PRE-1u.tar.gz -- Vidar