similar to: Home use of asterisk

Hi, Can anyone tell me if the Motorola Q has its Bluetooth always on like the IPhone? I want to use the Motorola Q in a Proximity Detection setup like that described on nerdvittles.com. I know the Treo 650 does not work well since the display must be on for the bluetooth to be on and this eats power. Thanks Chuck Bunn

Hello, On a LAN, is it possible to install a bluetooth dongle on one workstation (at this time, this workstation OS is not specified) and use it with chan_mobile ? I've read some USB over IP (or Ethernet) middleware exist but I'm not certain I'm looking at the right direction. Regards -------------- next part -------------- An HTML attachment was scrubbed... URL:

Here is a question that needs a few opinions... Recently we installed a couple of FXS gateways into a site with a SIP Proxy/Softswitch other than Asterisk. One of the things that the users on this site need to do is receive calls on single line phones on the FXS gateways and then hookflash and transfer them to other SIP users. We found that the FXS units, true to their nature as VoIP gateways,

List, Having a little trouble with the following. Let me prefix by saying I have blind transfers working from the following setup. Inbound call [from-zap] (SIP/sv0071iv) answers. Zaptel -> Asterisk -> SIP extension SIP extension then blind transfers [from-sip] --- SIP extension -> Asterisk -> Zaptel During this whole process, the original channel off the trunk (lineside T1) is

Hi, I'm helping out with a political campaign and would like to use asterisk to blast out about 200,000 calls with a short message from the candidate. Provider: I'm thinking voipjet may be a good solution? Hardware setup: I will have access to several T-1 lines so I would just want to set up the dialers to limit the number of concurrent calls and so forth. I found teleyapper on

Don't know what else to call this. Googling and some time on the IRC channel haven't gotten me anywhere. Here's the sitch, which is a bit complicated but is something my customers are in fact encountering on an everyday basis: 1. Bob is on a Zap channel talking through the PSTN to Carol. Both have the misfortune, like so many of us, of having LECs who do not offer disconnect

I've got a piece of CPE equipment that has an FXS port that I have tied to an FXO port on a TDM400 clone card. Normally, if I go off-hook with a standard telephone connected to it, I get a dialtone. If I dial a digit, and send a hookflash, the device will provide a dialtone back for the next available channel on the device. I'm trying to recreate this same behavior with Asterisk,

I repost a message I put a week ago: I have a Cisco IAD 2431 which has MGCP protocol; I cannot make it to work againts Asterisk; at least there is some MGCP conversation between them but when I offhook a phone attached to IAD I get no tone at all. As anybody managed to get working Asterisk against an MGCP Cisco gateway ? Which MGCP version should I use ? Also I recently

Hi, Has anyone out there managed to do a hookflash transfer with a Micronet 5050s gateway ? We have just tried out this gateway and it seems to do everything we need except this particular feature. Also if you have succeeded where is the hookflash time specified in the gateway. There does not appear to be any parameter for this. Perhaps it is not supported at all. Any help appreciated.

I wonder if I'm the only one whose customers are having trouble with hookflash on their TDMXXX cards. The problematic situation of record for us is a user who is on a call, and then wants to do one of two things: Hang up that call and take another one coming in Hang up that call and make another new call What happens is that instead of seeing the event as a hangup, asterisk perceives

Hi, I'm using zaptel with three way calling and call transfers with a hookflash. If I try transfering a call to an extension that is engaged I get an engaged tone. This is fine, but how do I get back to the caller? If I hookflash again I seem to put on a three-way call and the caller can hear the beeping. I can press hookflash again but I'd prefer the caller to hear only the hold

Hello, I've been trying to send traffic to a Cisco Call Manager 3.2, but with no luck. Here's whats happening: * Call gets to CCM * Call gets to the gateway * Rings a couple times on destiny * Call gets hungup. On the CCM I get the following error: MediaManager - ERROR wait_AuConnectErrorInd On the Gw (Cisco AS5300) I get a disconnect cause of 2F (Resource not available) On asterisk:

Hi all, I'm using following software and equipment and I have very strange behavior: Asterisk CVS-NHEAD-05/30/05-16:42:41 H323 gatekeeper - GnuGK 2.2.2 IAX2 client - Firefly 1.9.8 build 3945 H323 client - SJPhone Build 1.50.271d H323 gateway - Welltech Wellgate 3504A When I dial from Firefly (IAX2) -> SJPhone (H323) everything works as expected. When I dial from SJPhone (H323) ->

First question, is there a forum for asterisk@home specific questions? I've asked what must have been questions about asterisk@home here and gotten some indication they weren't welcome. Second, does anyone know what files need to be backed up? I don't need to back up the entire system since I can reinstall from the CD in fairly quick order, however, other than the files in

Hi, My configuration is SipPhone<-->*1<--->*2. My asterisk version is 1.4beta3. I installed pwlib,openh323,chan_h323. When i call from SipPhone--(SIP)-->asterisk1---(H323)-->asterisk2, there is no audio. Using 'rtp debug', I can see that rtp packets are being received. Rtp packets are being exchanged. I also tested chan_ooh323, but to fail. Can anyone recommand best

Hi, I've looked high and low for any changes that streaming MoH needs on Asterisk 1.4 (.21), followed NerdVittle's article about it (http://nerdvittles.com/index.php?p=92) yet nothing worked. After creating dir stream/ and touch stream.mp3, here's my musiconhold.conf [stream] mode=mp3 directory=/var/lib/asterisk/mohmp3/stream stream =>

Putting the Genie Back in the Bottle: More RedHat Legal Shenanigans with CentOS http://nerdvittles.com/?p=8721 Closing the Book on CentOS: [...] http://nerdvittles.com/ Thanks to the author of the above articles. jb

I just got cepstal working fine in the dial plan using code like: exten => 511,5,AGI(cepstral.pl|Welcome to my house finder. At the beep enter your zip code.) The php script it calls is based on the nerdvittles weather one so it calls a webpage which prints to the screen, the nerdvittles code uses system to generate the .wav file then has the dial plan call it via: //php script $retcode2 =

hi .. i've just installed and licensed an instance of the G729 codec. I am trying to connect through asterisk to Go2Call server .. According to their info it involves dialling extension 729 on voip01.go2call.com, to get the IVR. my extensions.conf shows : exten => s,2,Dial(OH323/h323:729@216.52.153.206) which I think is correct, I have G729 enabled in the OH323.conf file and it seems to

Hello World, I am a newcomer to this technology. I am very pleased to have found it and VERY interested in using it, as a better-cost alternative for schools where I teach open source & Windows technology. I travel the world, and help set up schools in underprivileged countries where it is very expensive to acquire the Windows desktop. Wine seems like a VERY good solution, much better than