similar to: IP Phone support SIP and IAX

Hi All; Till now I am not able to find a good IAX IP Phone or Gateway that can be used with good quality. Anyone can advise for good one? Regards Bilal ____________________________________________________________________________________ You rock. That's why Blockbuster's offering you one month of Blockbuster Total Access, No Cost.

Hi All; Anyone knows an IAX IP Phone works fine and tested? Does polycom support IAX IP Phone? Regards Bilal

Hi List; Where I determine the codec to be used for the SIP Trunk (between Asterik and another SIP softswitch)? Regards Bilal ____________________________________________________________________________________ Be a better Heartthrob. Get better relationship answers from someone who knows. Yahoo! Answers - Check it out. http://answers.yahoo.com/dir/?link=list&sid=396545433

Hi List; What the following mean: CONSOLE=Phone/phone0 CONSOLE=Console/dsp TRUNK=Zap/g2 I know SIP/John and Zap/1 but I do not know above (I do not know also the difference between Zap/2 and Zap/g2)? Any advise? Regards Bilal ____________________________________________________________________________________ Got a little couch potato? Check out fun summer activities for kids.

Hi All; I tried Firefly softphone with IAX and it gave very poor quality. Any one advise a good strong softphone that can work with IAX fine? Regards Bilal ____________________________________________________________________________________ Be a better friend, newshound, and know-it-all with Yahoo! Mobile. Try it now. http://mobile.yahoo.com/;_ylt=Ahu06i62sR8HDtDypao8Wcj9tAcJ

Dear; Thanks a lot for guiding me. Is it possible that the installation libpri-1.4.11.5 newer than the libpri-1.4.11.5-patch? Well, when I typed (note: I am trying to apply the libpri-1.4.11.5-patch for the libpri-1.4.11.5): libpri-1.4.11.5# patch -p0 -i libpri-1.4.11.5-patch It gave me that patched detected as shown below (example of one file, and I got same for other files): patching file

Hi List; If I am configuring Diguim Analoge card, then I need to run #modprobe wctdm, but the question why I need to run #modprobe zaptel also? What #modprobe zaptel does a things that #modprobe wctdm does not do? Any help? Regards Bilal ____________________________________________________________________________________ Looking for a deal? Find great prices on flights and hotels

Hi List; [incoming] include => parkedcalls exten=103,1,Dial(SIP/Bob,,tT) exten=104,1,Dial(SIP/Charlie,,tT) When we use tT and when we use t alone or T alone, I know this for call parking, but I do not know what the tT does? Regards Bilal ____________________________________________________________________________________ Sucker-punch spam with award-winning protection. Try the free

Hi List; My Asterisk version is 1.4 and I am trying to use the ResponseTimeOut() application to control the response time of the Background function, but when the running arrive for the ResponseTimeOut() then the call drop and my debuging says: No Application 'ResponseTimeout' for extension (Test_Bilal,s,3) Spawn extension (Test_Bilal,s,3) exited non-zero on 'Zap/1-1' Hangup

Hi List; I heared that IAX is good for NATing issues, but I do not know if it can help me in that senario: I have two Asterisks machines in different sites and both are behind NAT (both have private IP address), I need to link these two asterisks with IAX trunk (if it help really in such senario), but I do not know if it will work without doing special routing settings on the router (like

Hi All; I can assign for my Asterisk Machine a two IP addresses (xxx.xxx.xxx.yyy and xxx.xxx.xxx.yyz), how can I use these two IP's so I can let one call sent with a source IP address xxx.xxx.xxx.yyy and another call to be sent with another source IP address xxx.xxx.xxx.yyz, I need this because I need the side to authorize my calls by the IP address, and some calls to be authorized with the

Dears; I do not know if any had experience in using speex or ilbc with IAX and got good results, because I am facing a problem with GSM. I am facing a noise problem when I am using GSM with IAX trunk as following: IP Phone (G711) ---> Local Asterisk Box ---> IAX Trunk using GSM codec ---> Remote Asterisk Box ---> Digium Card (FXO) to terminate the call to the destination While no

Hi List; I am trying to use wiki via the link (http://www.voip-info.org/wiki/index.php?page=Asterisk) in effective way to find the needed resource for me, but still it is hard to arrive for the needed information. For example: what is the best (shortest) way to search for information related to the command playbak()? Using the backlines, it make the eyes feel hard by keep reading without

Hi All; I am configuring IAX endpoint, I just need to understand why I have to set requirecalltoken = no to be able to register because the following message is displayed: [Mar 22 12:25:39] ERROR[2297]: chan_iax2.c:4251 handle_call_token: Call rejected, CallToken Support required. If unexpected, resolve by placing address 78.154.240.146 in the calltokenignore list or setting user gwbilalkwpciax

Dear List; I am trying to create a link between Asterisk and My softswitch, the link to be SIP Trunk. I did the below configuration and I do not know if any one can help me and advise me to have better configuration to be sure that link is fine. But I do not know how to determine the SIP username to be sent for my softswitch as sometimes the softswitch need to check it. Also, does asterisk

Hi All; How can I test manager.conf? Can I telnet to the asterisk machine at the port 5038 and send and receive commands to test if the manager is working fine? How? Regards Bilal

Hi List; I have this example for Macro and I am not able to understand some line, if any one can help me plz :)- [macro-voicemail] exten => s,1,Dial(${ARG1},20) exten => s,2,Goto(s-${DIALSTATUS},1) exten => s-NOANSWER,1,Voicemail(u${MACRO_EXTEN}) exten => s-NOANSWER,2,Goto(incoming,s,1) exten => s-BUSY,1,Voicemail(b${MACRO_EXTEN}) exten => s-BUSY,2,Goto(incoming,s,1) exten

Hi List; How can I configure asterisk to receive a call from SIP end point without being registered at asterisk and its IP address is dynamic, and authentication to be based on the username and password or any other string? I know that if I place the host with static IP then no need to register, but what if the voip gateway was having dynamic IP and I do not need to register on asterisk, but I

Hi List; I need to configure a softphone to be client and use it with Asterisk, which is the recommended one? Is it iax2? Regards Bilal ____________________________________________________________________________________ Boardwalk for $500? In 2007? Ha! Play Monopoly Here and Now (it's updated for today's economy) at Yahoo! Games.

Hi All; I do not know if anyone faced such case in dealing with open vpn (as we need it for fring to be used from the mobile: Which mobile can be used to install the open vpn client on it, so we can use it to do a vpn channel with the server that has open vpn server? Regards Bilal