similar to: IAXy ringing

Greetings all- Long story short - I find myself suddenly running a Asterisk PBX after old PBX suddenly died. Fortunately, I had been "playing" with Asterisk (via Trixbox) on a server in consideration of replacing our aged Merlin Legend - so over the course of last weekend, I brought my testbed PBX up to full operation and now supports about 30 users. All in all, went smoother than

Hi! I'm really hope you can help me solve a little mystery, the mystery is probably just my misunderstanding ! sorry... I've got an iaxy talking to my * box which connects to two providers. I'm running the stable release of the pbx. The only thing is that when dialling from the iaxy the ringing tone isn't heard while calling someone - you just hear silence then, they either

Hey Everyone, I recently purchased a few IAXy units for some testing, and have come across a some problems. One of them can be provisioned but will not ring the connected telephone. It also does not provide a dial tone when you pick up the phone. When a call is made to the IAXy one of the green lights on the board goes from a solid on state, to a flashing state that coincides with the

I have an iaxy the is across a 802.11b link from my asterisk server. signal strength is good and it has been working fine there for about a year. Friday night lightning took out the x100p card in my asterisk server and I just got it all working again last night. Lucky I had a spare. Since I got every thing setup I have been having problems with the iaxy - I really doubt that it is lightning

I have a couple Iaxy's and when calling out on them I dont hear ringing. Everything else is working fine. Any ideas? THanks, Jerry

Hi all, getting a server going wiht a few TDM400's and some phones, and some IAXys too I haven't heard any issues about AU phones being able to RING in Australia, like the problem in the UK with ring capacitors on the BT system. Are there any problems like that? Also, with the iaxy's -- they should work (and ring) in Australia right? The only hint I'm seeing around is the use

I have a brand new IAXy I'm playing with. I do not get a dialtone on the phone, or any response at ll on the phone. No sound, no dialing, no ringing. The phone and wire are tested and known to be good. I think I have it setup correctly. When I give the iaxprov command I get this: #iaxyprov 192.168.1.90 iaxy.conf 02: c0 a8 01 5a 05: 11 d9 03: ff ff ff 00 04:

Just setup *, got a developers kit FXO where the incoming/outgoing pstn is plugged in. I've then got an IAXy that is plugged into a Philips DECT phone. * is setup so that the [bell] section rings the phone - exten => s,1,Dial(IAX2/myuser,30) What's happening when someone calls my number is that the phone rings 3 times before you hear the dect phone ringing. Anybody got any ideas as

I'm having some problems with a bunch of older IAXy devices. I have three S100I devices working. I can call each device from each other and everything works perfectly. When an inbound call comes in (from PSTN) and is routed to the device, it works perfectly as well. The problem is that when I place an outbound call (to PSTN), the remote party can hear me well, but I cannot hear the

Hi all, I have a small query regarding ringing tones on an iaxy2. I have a customer who uses an iaxy to breakout to pstn via our *. However the customer complains that he gets no ringing tone whislt making calls, i just visited the site and can confirm this. I also have another customer who is presently in canada with an iaxy calling thru our * , he doesnt have this issue. I presume that the

I hope somebody has seen this before... I'm trying to use a Dial command on a inbound call to ring multiple destinations. The calls come in to me from the provider on IAX2, and one of the destinations I try to ring is a IAX2 to call to my cell phone. When I add the IAX2 destination into the Dial command, the setup I am trying to achieve works (i.e. my Zap, SIP, and cell phone all ring) but

How do you setup the timing in Meetme conference? I have a x100p and tdm4x card. When I dialing to my conference I get a request to schedule in the past error message. thanks -----Original Message----- From: asterisk-users-admin@lists.digium.com [mailto:asterisk-users-admin@lists.digium.com] On Behalf Of asterisk-users-request@lists.digium.com Sent: Saturday, April 10, 2004 10:48 AM To:

Hello all, In changing the phone connected to my IAXy I remembered that this phone will not ring on the standard frquency (20hz?) when connected to the FXS. There is a patch, one line to change in wcfxs.c for use with a TDM400P, but obviously this doesn't change the FXS on the IAXy. Is there any possibiity of a "patch" for the provisioning data to raise the frequency to 25hz on the

Hi, Has anyone got faxing working via an IAXy? I'm having trouble getting it working with a fax machine here. The IAXy works fine, I can make incoming/outgoing calls via it, however our PDQ takes a few redials to get data over to the dialled party, and faxing doesn't seem to work at all. I have turned off all the echo cancellation stuff, just in case that was an issue. Anything I

I have Asterisk running with a combination of SIP and H323 clients. I am using the OH323 module instead of the H323 one. When the SIP clients ring each other, they can hear a ringing noise in the ear peice to let them know that the other parties phone is ringing. However, when the H323 client rings a SIP client, there is no ringing sound at all, although as soon as the called party picks up the

Is the a way for IAX2 adapter to detect when the calling party hangs up the phone? I have two IAX2 adapter, one is Digium IAXY when I call the IAXY extension and hang up the phone the IAXY adapter rings about two or three times after the calling party hangs up the phone. The new adapter AG-188N with IAX2 protocol as well does the same thing, the phone rings 2 or 3 times after the calling party

I just bought an IAXy and have been using it with * and NuFone. Around once every 24-48 hours of operation (not off hook, just powered up), when I pick up the phone I hear loud static instead of dialtone. If there's an incoming call, the phone will ring and * CLI will show that it's trying iaxy, but when picking up--no answer to * and loud static. The incoming call goes to VM. Cycling

It's happened before, cleared up and now it happened again. The IAXy, working for a total of about 6 months. Symptoms: Registered with asterisk and even receives calls (the LED shows it's ringing) but phones connected to it are dead. Same phones work connected directly to the phone line. Cable swapped out, no difference. Endless re-provision (with normal looking output) and power

When I call my internal extension and hang up the phone keep ringing, I get: SIP/11-00000048 connected line has changed. Saving it until answer for IAX2/iaxy Is there a solution for it? SIP does not detect that IAX has hang up the line. -- Joseph

I'm having a problem with my IAXy not always connecting to my Asterisk box. When I pick-up the phone plugged in to the IAXy I get a busy signal. I have to hang-up the phone and wait a few seconds after the orange LED goes out and then try again. When this happens I don't see any connection attempts in the Asterisk -r output. When I do get the IAXy to connect to Asterisk I get a