Displaying 20 results from an estimated 8000 matches similar to: "no outoging calls with B410P"
2008 Jan 07
1
no outgoing calls with Digium B410P
Hi all!
Sorry for my poor english, i'm italian.
I installed Digium B410P on my asterisk server. I followed the official
installation instructions found on digium site. These instruction, in my
opinion, are not clear, so i tried with other ways (found on the trixbox
site). I found this:
http://www.trixbox.org/forums/trixbox-forums/trunks/howto-install-script-digium-b410p
Now i can receive
2004 Nov 26
3
Billing of outoging calls via CAPI
Hello all,
I would like to get billing/charging informations of all
outgoing calls of any PSTN numbers made with my IP-Phone via asterisk.
Can I obtain in * an accurate charge information of outgoing call via CAPI which
destination is any PSTN number?
Does the ISDN "signal" contain charging informations ?
Thank for advice
Rastislav
2008 Jan 11
1
interconnecting an asterisk server with an old alcatel PBX through a Digium B410P
Hi guys,
I need to interconnect an asterisk server (1.4.17) with an alcatel pbx,
because i want that an asterisk extension can call an alcatel extension
and viceversa. I need to do this throug a NT port (of the digium card)
for technical reasons (linked with alcatel hardware).
Card installation was fine, but i'm not sure of the configuration i
choose. In /etc/misdn-init.conf i put my
2016 Jan 06
2
ICMP outoging traffic at centos 6.7
Hi,
>From last some days I am facing the unexpected huge ICMP traffic is going
out from Server.
I have blocked icmp ports in iptables and if I execute the Ping manualy its
blocking.
Some process is send this huge traffic. Below is tcpdump output.
================================
16:23:27.817856 IP (tos 0xc0, ttl 64, id 55278, offset 0, flags [none],
proto ICMP (1), length 104)
2016 Jan 06
0
ICMP outoging traffic at centos 6.7
On 01/06/2016 04:45 AM, Shital Sakhare wrote:
> I have blocked icmp ports in iptables and if I execute the Ping manualy its
> blocking.
...
> How this can be controlled ?
Drop the incoming traffic in iptables, rather than rejecting it?
2016 Jan 06
2
ICMP outoging traffic at centos 6.7
Thanks, Dropped the ICMP type 3 port. Now question to find the cause.
On Wed, Jan 6, 2016 at 6:49 PM, Gordon Messmer <gordon.messmer at gmail.com>
wrote:
> On 01/06/2016 04:45 AM, Shital Sakhare wrote:
>
>> I have blocked icmp ports in iptables and if I execute the Ping manualy
>> its
>> blocking.
>>
> ...
>
>> How this can be controlled ?
>>
2016 Jan 06
0
ICMP outoging traffic at centos 6.7
On 01/06/2016 05:47 AM, Shital Sakhare wrote:
> Thanks, Dropped the ICMP type 3 port. Now question to find the cause.
Well, based on your tcpdump output, it looks like your rules were
rejecting unrelated packets, or tcp/443 packets. It's hard to be sure
since the ICMP was the first packet, so you didn't show the packet it
was actually replying to.
The ICMP traffic is a result of
2009 Jan 05
1
B410p, Ast1.4, France Télecom Numeris Double T0 problem
Hi.
When I call my RNIS numbers (with a mobile phone for example), I can
see 2 incoming calls on the IPBX, which should not happend.
I'm not sure if it's a problem with the telco France Telecom and their
ISDN setup, or if it's a problem
with the MISDN driver on the IPBX itself.
I'm stuck ...
Any advices for troubleshooting that?
Someone provide working configuration files
2016 Jan 06
2
ICMP outoging traffic at centos 6.7
Yes, now I am dropping packets in OUTPUT chain for type 3. Initially, I
implemented the chain to drop type 0 and 8. But it wont worked and the
packets were hitting at firewall for multiple ICMP requests. I didn't
Understand the problem. After posting here I go through all the types of
ICMP types where I understand to drop packets for "Host unreachability" .
Thanks for your help Mr.
2010 Oct 23
2
B410P - BRI NT 100 Ohm terminator
Hi,
My set up is :
Asterisk with B410P in NT mode <-------------cat5 straight cable
----------------> Another PBX in TE mode
Is the 100 Ohm terminator you can find on B410P boards, necessary when
connecting in NT mode to another PBX (set in TE mode) ?
Cheers
-------------- next part --------------
An HTML attachment was scrubbed...
URL:
2007 Nov 17
1
Building and running mISDN for B410P on Ubuntu 7.04
Hi.
Using Asterisk 1.4.13 running on Ubuntu 7.04 with Intel CPU:
1) Not being able to build mISDN on Ubuntu using "make b410p" I have used
mISDN-1_1_7 which seems to work ok. QUESTION: Should I expect this version
of mISDN to work ok with these cards? Or is there a way to build using "make
b410P" on Ubuntu? (make force does not help at all)
2) In some of our installations
2007 Feb 22
2
b410p + fax (echo cancellation)
We have recently purchased a B410P Digium 4* ISDN-2 card with hardware EC.
On the same server, I also have a regular Digium 4-channel PSTN-card
(TDM410P ?), used to interface to some analog devices, a.o. 2 fax machines.
For faxing, EC needs to be off (or so I understand from the archives).
How can I switch EC off for an ISDN B-channel if a fax is coming in?
Z.
2008 Feb 22
2
Digium B410P and 8 ports connectivity
Hello,
Junghanns and BeroNet offer 8 BRI ports cards.
Do you know if Digium's B410P has an inner TDM bus so that an 8 BRI ports
subsystem (2 PCI slots used, but 1 one set of interrupts) could be made out
of 2 B410P ?
I know you could (theorically) do this with Junghanns and BeroNet cards.
Cheers
-------------- next part --------------
An HTML attachment was scrubbed...
URL:
2009 Mar 10
1
Asterisk 1.6, B410P and TE/PtmP mode. Could you get it running ?
Hi,
My setup is:
IPPhone1 --- Asterisk1 with B410P ---- Patton 4638 --- Asterisk2 ---
IPPhone2
I want to evaluate Asterisk1 in TE/PtmP mode.
So, Patton box is configured in NT/PtmP (with 3 BRI links between both
systems).
Anyway, asterisk -rx "pri show spans" keeps replying :
PRI span 1/0: Provisioned, Down, Active
PRI span 2/0: Provisioned, Down, Active
PRI span 3/0: Provisioned,
2008 Dec 09
2
B410P, dahdi in TE, PtmP mode ?
Hi,
I've read that the new dahdi channel supporting B410P doesn't support PtmP
when in NT mode.
Does it support PtmP when in TE mode ?
Cheers
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20081209/f422b5d0/attachment.htm
2009 Jan 22
2
Incoming fax detection on mISDN hfcmulti B410P card
Hi,
I'd like to know what's the most "popular" method for automatic fax/voice detection for incoming calls on mISDN cards such as the B410P (hfcmulti).
I'm running:
kernel 2.6.17
misdn 1.1.3
asterisk 1.4.21.2
B410P card
I'm using iaxmodem and hylafax with asterisk (the setup works for zap channels).
I've used the following options in /etc/asterisk/misdn.conf:
2006 Nov 24
1
Installing the b410p card, unable to install mISDN
Hi,
I'm installing Asterisk on Ubuntu 6.10
When I first compiled the zaptel package I used:
make clean
make
make install
So far so good, but the following command failed:
make b410p
I did some digging on google and found a guide on how
to install it manually, but the result was the same.
I got these files
ftp.digium.com/pub/telephony/zaptel/b410p/misdn-b410p.tar.gz
2008 Feb 21
1
Which echo-can for Digium B410P ?
Hi,
Which echo-canceler shall I pick for Digium B410P ?
Is HPEC relevant ? Reading from its datasheet, it seems related to analog
cards.
Regards
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20080221/ed5c5d6f/attachment.htm
2009 Sep 04
1
1.4.26-2, DAHDI-2.2.0, B410P and BRI
Hello everybody,
I try to install -Ubuntu 8.04 server- a B410P and a TDM2400P together
with Asterisk 1.4.26-2, dahdi-linux-2.2.0.2 and dahdi-tools-2.2.0.
Problem I face is the following one:
CLI> module load chan_dahdi.so
== Registered application 'DAHDISendKeypadFacility'
== Registered application 'ZapSendKeypadFacility'
== Parsing
2009 Mar 11
3
Digium B410P: misdn v1 or misdn v2 or dahdi + asterisk 1.6 ?
Hi,
Until now I've been using my Digium B410P cards with misdn 1.0.x.
I would like to upgrade my systems and am now wondering which is the "best" route to take:
- use the latest release of misdn v1
- upgrade to the latest "stable" kernel and use the built-in misdn v2
- use misdn v2 as a seperate package (disable misdn in the kernel)
- use dahdi's support for misdn