similar to: b2bua

I am trying to setup asterisk as a registrar and sip server only. Currently When I make calls all my rtp traffic is going through the asterisk server as a B2BUA. Is it possible to turn off this feature and have all my calls RTP traffic going directly to the SIP UA? -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi everyone, any chance * could be used as a b2bua without forcing the media stream through the same box? I would love to do some computing on incoming calls, do things like setting another callerid and the forward the call to another sip UA - all without any audio traversing the * box. Any ideas? Thanks, Thilo

Hi, What are the current best practices for running asterisk as SIP B2BUA? Are there any sample configs online or the books that detail this configuration for the newbies? I'm going to run it behind 1:1 NAT for the clients in the public internet so I will use the externip, localnet, and nat settings. Thanks, Andrew

Hello, all. Alas, another convoluted question. All the simple things are, well, simple so I suppose we only need to trouble the list with squirrely problems! We've noticed a call history problem when using Asterisk where the call history on the Snom phones (with which we are very pleased) reflects the number of the PBX extension used by the B2BUA to dial the end point. I assume the same

Hello all! It's my try to make b2bua from asterisk. It's patched asterisk and some AGI script for it. What it support? Full vovida's b2bua radius emulation, radius failover, LCR, Call failover, Codec based routing, Session-Timeout and much other things that can be useful. Any suggestions and critics welcome! http://b2bua.berlios.de Best regards, Mike

Hello all! It's my try to make b2bua from asterisk. It's patched asterisk and some AGI script for it. What it support? Full vovida's b2bua radius emulation, radius failover, LCR, Call failover, Codec based routing, Session-Timeout and much other things that can be useful. Any suggestions welcome! http://b2bua.berlios.de Best regards, Mike

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hello, Is the asterisk B2BUA patches useful anymore?? I'm trying to set a prepaid SIP network and the only way seems to get through a patched asterisk with B2BUA functions.. The patches failed, Hunk + problems: I have repaired them, but is it very useful?? Thanks -----BEGIN PGP SIGNATURE----- Version: GnuPG v1.4.7 (Darwin) Comment: Using GnuPG

Hello. LCR means least cost routing, and it's billing system problem where to route a call, not b2bua's. But currently I dunno any free billing system that support it, so i moved this logic to b2bua. On Sat, 12 Feb 2005 07:05:39 +0330, mohammad <mohammad@mirzaee.net> wrote: > Hi Mike; > Thanks for your new application, but I think it would be better if you put >

Any tips on solving the following performance conundrum: Asterisk 1.8.12.2 running on HP DL360 G5 and G7s tcpdump running to capture UDP 5060/SIP signaling to .pcap files All calls are ultimately B2BUA client -> asterisk -> PSTN Media stays on Asterisk at all times AGI script has exit handler that connects and updates an external database upon BYE from either side. I know that if exit

Hi All, I am seeking input from anyone who may have seen a similar configuration and dealt with similar issues to what I'm experiencing. Configuration: - 2 sites (site A and B) - Asterisk 1.2.23 on each site (Trixbox) - Internet 512/512 symmetric at each site, dedicated to VOIP calls only. - IAX trunk between the sites, with data travelling across the 512/512 Symmetric link - PSTN

According to this page: http://www.asterisk.org/doxygen/Config_sip.html canreinvite=yes redirects just the RTP. I was under the impression that the entire SIP connection got redirected, therefore losing accounting ability. Could someone clarify this? --Mike -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi, I am familiar with asterisk, though never actually tinkered with one myself ... so i don't know the full extent of its capabilities. I am facing a request to bridge a sip network and an h323 network. I would like to operate the sip with ser as the proxy and some gatekeeper on the h323 side (not required though). Actually, i have a few more points that may make it simpler - i do not need

Sorry, but why u r using the Radius with the CDR? Not enough to access the CDR in the /var/log/asterisk/cdr-csv/Master.csv? Also, what kind of Radius u r using? Any suggested link? Regards Bilal > > Hello list. > > I'm having some problems with the CDR Radius in my > Asterisk 1.4. I'm > using two TC400B cards for transcoding. When I reach > nearly 100 >

Hi all, I am having this problems for a while and could not figure out the cause of this. I have FreePBX version of Asterisk (1.8.11-cert) routing calls to 10 different FreePBX servers (same version of Asterisk) depending on the destination numbers. The incoming calls into the main Asterisk server with 4 x Sangoma A102 E1 card are coming through a SS7 link from an ISUP interface of a

<!DOCTYPE html PUBLIC "-//W3C//DTD HTML 4.01 Transitional//EN"> <html> <head> </head> <body bgcolor="#ffffff" text="#000000"> <font size="-1">Hi,<br> <br> i use a ser, as proxy sip server(authentication), then a cisco router as sip2h323 gw(authorization and accounting). i want to start asterisk as sip statefull

Hello all, It's my try to make some 'emulation' of vovida's b2bua using asterisk. I was in rush while writing it, so I sure there is much code that can be cleaned, great that not too much. :) http://dslmax.boom.ru/asterisk_b2bua_v0.1.zip cdrradius and agi script inside. __ Mike Tkachuk

Hi Everyone, I was hoping someone might know why I am experiencing a problem with Asterisk logging the event: [May 3 12:07:41] WARNING[30371] chan_sip.c: Maximum retries exceeded on transmission 03f007af2b15cd0b54b0c368265d97be@sip.externalprovider.com for seqno 669371069 (Critical Response) This is happening after: - call is setup, 2 way audio - call can function correctly for up to 5

Hi, I want to be able to bridge two sip channels using direct RTP between my endpoints (Audio IP : not local) but without using reinvites. So I set up my asterisk sip endpoints as follows: [test1] type=friend host=dynamic username=test1 dtmfmode=info context=test_rtp allow=all canreinvite=no directrtpsetup=yes [test2] type=friend host=dynamic username=test2 dtmfmode=info context=test_rtp

I understand Asterisk is more like a B2BUA. But when this INFO request is sent to asterisk, asterisk is supposed to bridge the request to the other endpoint, right? In what situation, it decides to send a reply; in what situation, it decides to bridge the request? What is the role of gateway in SIP world, a proxy, a B2BUA or something else? Thank you, Wei Date: Fri, 18 Mar 2005 12:51:28 -0600

Hello, Could somebody tell me is it possible to use asterisk without RTP proxying in SIP<->H323 calls? I mean exactly what canreinvite=yes option do in SIP<->SIP calls. I don't need a transcoding, only a signaling conversion, and this is possible with some softswitches, so i wondering what about asterisk. Same question about H323<->H323 calls I'm using NuFone