similar to: Telco MWI Detection on TDM400 Interface?

I've upgraded to asterisk-1.6.0-beta2. I'm trying to get the new Telco MWI detection function working. It doesn't appear to be working. I have this in zapata.conf ; PSTN connected here ;immediate=no ;busydetect=yes ;busycount=8 ;musiconhold=default mwimonitor=yes ;mwilevel=512 mwimonitornotify=/usr/local/sbin/zapnotify.sh faxdetect=incoming signalling=fxs_ks context=incoming

Folks, I've tried to find a reference, but I've had no luck, and would appreciate your thoughts: I'd like to be able to monitor a telco line for Message Waiting Notification, however I cannot figure out if this capability is available. Detecting either FSK or Stuttered Dial tone would serve, but I can't find anything in the list archives or Wiki with clues as to how this might

Howdy I have a question regarding support for picking up when the telco sends a MWI message. My client's setup is a small office with three incoming lines on a TDM400P with iaxy's and a Grandstream as extensions. I am using CVS Head from yesterday. (I was resolving a different issue.) Since they only have two voice lines, with the third as a fax, I am using voicemail from the telco.

I've been having trouble with making outbound calls to my TELCO from a TDM400 card (FXS KS signalling) after upgrading from 1.6-beta9 to 1.6.0. The problem is completely intermittent. When it fails, I get this message: [Nov 9 19:12:26] WARNING[18916] app_dial.c: Unable to create channel of type 'DAHDI' (cause 0 - Unknown) At some point, it starts working, but I don't know what

We are using Bellsouth 8867 phones on our TDM400B FXS lines (asterisk-1.0.3). It has a "Voicemail" light, which appears to be MWI (according to the manual it works with voicemail from the telco that sends a FSK signal). The dialtone stutters when a line has voicemail, so I know that I have the mailbox setting right in zapata.conf, but the light doesn't go on. I am also getting

I have my peers registered to SER.asterisk seems to be sending mwi for the peers seen in the sip show peers CLI command. i have my ser server registered with asterisk as a type=friend and all clients register to ser.how do i get mwi to work for these clients registered to SER. Thank you, -AA

Hi All - I'm running version SIP version 1.3.4 on various IP300, IP500, and IP600 Polycom phones. I'm having a tough time with MWI. I thought I remembered somebody on the list saying that they had it working, but I can't find it in the archives now. I have all the phones configured for MWI as specified in the WIKI: ipdmid.cfg: up.oneTouchVoiceMail="1"

All, I'm using Asterisk 1.6 and using Polycom 500's with SIP firmware 2.1.3. I can not seem to get the Message Waiting Indicator to work reliably (and in my opinion correctly) with voicemail. I've got the following in my phone.cfg: <reginfo> <msg msg.bypassInstantMessage="1"> <mwi msg.mwi.1.callBack="*97"

Hi list, how does one get a SNOM 200 MWI to work with * ?? When I press the MWI button it doesn't connect with voice mail on my * box. thanks

Hi, I have lookedaround and don't see this anywhere. Is there a way to tell the ip500 to not make the aural MWI blips?

Hello everyone, My setup: Debian squeeze Asterisk 1.8, DAHDI, libpri, compiled from source TE110P, attached to a Deutsche Telekom Octopus E Modell 300/800 I'm trying to get MWI for Voicemail working. In the same server I have also got an Eicon DIVA PRI card for testing purposes (it is integrated via CAPI and the chan-capi channel driver into my Asterisk). MWI works just fine there. I

I need to setup MWI on a few Aastra 9112's. I've tried doing so in the web interface by setting "Explicit MWI Subscription" to true, but no lights, no stutter tone. Firmware: 1.4.0.1048 Thanks! -- Warm Regards, Lee

Does anyone have personal experience with a 5.8gig wireless phone (system) that has an MWI that WORKS with asterisk via fxs (in my case spa3k) generated MWI. I know the spa3k does stuttered dialtone but not sure if it generates FSK MWI. I see some that state they do but I also see reviews that say they don't. Doug

I have a Sipura 962 endpoint on Asterisk 1.4 where the MWI works perfectly, however my theory is that it should be broken. Obviously I'm wrong but "Sip show subscriptions" does not show the endpoint subscribing to the MWI status on Asterisk, even though all of the other endpoints on the system DO subscribe for their respective mailboxes, including SNOM & Polycom endpoints.

Hello I am running the following setup in order to make VoIP calls at home. Home Phone <-> SPA3000 <-> Asterisk Home <- IAX2 over Internet <-> Asterisk Office The voice mail for Home Phone is hosted on the Asterisk Office machine. I wanted to have a way to check the status of my voicemail on my home phone directly. In order to do so, I've patched both Asterisk Home and

I'm trying to get the Telco MWI recognition working in asterisk-1.6-beta7. I'm told that it's supposed to work provided my telco support FSK MWI signalling. I have Verzon FIOS. I believe I have FSK MWI signaling as I can hear the standard stutter tone when I pick up a live handset in front of my asterisk connection. I have the Verizon line attached to a TDM400 card, port 4. I

Hi ALL, After upgrade 1.8 my MWI wasn't working I do have setting in voicemail.conf. Do i need to do anything else to fix my MWI on polycom 501 ? It was working with 1.2 asterisk. pollmailboxes=yes -------------- next part -------------- An HTML attachment was scrubbed... URL: <http://lists.digium.com/pipermail/asterisk-users/attachments/20110608/e1f59a92/attachment.htm>

Hello, it is possible to get MWI working with Grandstream and Asterisk? Thanks. -David

Hi guys, is there any way to execute a command *after* a caller has hung up the call? Something like exten => s,1,Voicemail exten => s,2,AGI(mwi.agi) I'd like to turn off the MWI on my cellphone (which is done by gammu[1]) Or does anyone know a way to check the state of the MWI from outside, i.e. with a cron-job? I'm turning on the MWI with the email-notify from voicemail, but

Hey there. I've been working on a project to integrate Asterisk with Exchange Unified Messaging via sipX using large parts borrowed from: http://blog.lithiumblue.com/2007/04/accessing-exchange-2007-unified_29.html ... and everything works surprisingly well. The one problem I have is MWI, or a lack thereof. Exchange 2007 doesn't support MWI of any kind (!), so I've been looking into