similar to: Newbie question: how to proxy the *real* caller-id on find-me/follow-me

Sorry if this comes in twice. Wasn't subscribed first time :-( Anyone help me here...... It worked once :-( I have a static IP address which is on my private network.. Phone is 192.192.192.220 and asterisk server is 192.192.192.22 I have the 7690 with a SIP iamge (Whatever latest is ) I have 3 lines setup with Free World Dial up and have the 4th setup to connect to my asterisk server.

Anyone help me here? I am a newbie so be gentle ;-)...... It worked once and then I played with the configs. I have a static IP address which is on my private network.. Phone is 192.192.192.220 and asterisk server is 192.192.192.22 I have the 7690 with a SIP iamge (Whatever latest is ) I have 3 lines setup with Free World Dial up and have the 4th setup to connect to my asterisk server. Here

I am running asterisk 1.0.1 with OH323 compiled in. We have a 323 trunk to CallManager with a mgcp controlled pri router. When using sip phones (directly registered with asterisk) to call out the 323 trunnk to PSTN, calls timeout after 3 rings. If I answer b4 3 rings - no problem, otherwise I get "no one is available to answer at this time" on the consoel and it redirects to an

I am new to asterisk and need to dig up some info on how to set it all up. It looks a bit daunting especially all the options available in the .conf files. I have 2 SIP phones, GXP2000 and a budgettone 100. phone1 - 192.168.0.160/24 extension 1000 phone2 - 192.168.0.161/24 extension 1001 Server - 192.168.0.57 I get the following all the time, but can make calls between the 2 extensions,

sip.conf.sample: ;register => 2345:password at sip_proxy/1234 ; ; Register 2345 at sip provider 'sip_proxy'. Calls from this provider ; connect to local extension 1234 in extensions.conf, default context, ; unless you configure a [sip_proxy] section below, and configure a ; context. sip.conf: [general] context=default allowoverlap=no udpbindaddr=0.0.0.0 tcpenable=no

I've been googling and talking with Libretel about my setup and the fact that incoming calls to my asterisk box through the Libretel number reach my box (I hear the greeting being played) but then don't accept DTMF. Here is a rough diagram of my setup: Asterisk | server | NAT <------------ Libretel | router | Note that there are NO SIP

I'm trying to set up my extensions.conf file using some of the existing macros like stdexten, etc. while at the same time having two logically separate virtual PBX's (with no "default" context) and two trunks coming into separate contexts, i.e. one for residence and one for my at-home business. I noticed, however, that macro-stdexten depends on the "default" context:

Hello guys. I am a fairly new user to Asterisk, and I'm just having a tough time. My goal is to set up a VOIP PBX. I have signed up with a BroadVoice number, and I have three systems with SIP phones. The PBX and the SIP phones are all behind a Cisco PIX running NAT. I am using Asterisk CVS version from yesterday. I also tried 1.0.3 with little luck. The SIP phones are two X-Lites on

I'm having trouble with both my Polycom IP600 and IP500 disconnecting calls to the PSTN after about 1 hour. The below log is of a phone call that lasted 1hr 39mins which is my record so far. I cannot figure out what is causing the call to terminate and I am hoping somone on this list can help me. In this example both the phone and the asterisk server have public IP addresses so NAT shoul not

Hey, Im running Asterisk 1.2.2 and im having problems with the audio when bridging calls between the zap interfaces and sip. zap to zap work fine, as do sip to sip (but asterisk isnt in the media stream, as it doesnt need to be) and terminating the call and playing a test message via either sip or zap work fine. Basically, the only time I see this problem is trying to bridge between sip and

Hi, to register my Asterisk with a SIP provider I use the following syntax, as shown in the default sip.conf: register => 2345:password@sip_proxy where [sip_proxy] type=peer context=from-messagenet host=sip.messagenet.it port=5061 <------------- please note this one!!! 5061 is provider's port I have to register to. This also would work for me: register =>

Hello fellow asterisk people! I have Asterisk listening on port 5061 and SER on port 5060. Asterisk is configured as a gateway for ISDN/Analog/H323 and also SIP. My problems are with SIP. I can make incoming calls from SIP to asterisk and to any of the other networks, but when I try to make an outgoing call from Asterisk to SER I see the following in Asterisk: -- Executing

Hello fellow asterisk people! I have Asterisk listening on port 5061 and SER on port 5060. Asterisk is configured as a gateway for ISDN/Analog/H323 and also SIP. My problems are with SIP. I can make incoming calls from SIP to asterisk and to any of the other networks, but when I try to make an outgoing call from Asterisk to SER I see the following in Asterisk: -- Executing

What is the relationship between the peer definitions and the register command? In reviewing the sample sip.conf it seems that you can place the "sip_proxY" peer as the hostname. Is this correct? This question adds the the Broadvoice thread and where to place the dtmfmode variable. sip.conf --- (asterisk sample) -------------------------------- ;register =>

I am having trouble setting this system up and wonder if some one help me. Does anyone know what is missing if anything to get 2 phones on my asterisk home server to be able to call each other. I have a WRT54GS running OpenWRT/asterisk connected to a PAP2 with 2 extensions 5060/5061, this is on the lan side of my gateway/router WRT54G 192.168.1.1 BusyBox v1.00 (2006.11.07-01:40+0000)

I want to setup a blind transer for auto forwarding to SIP peer. I have context forwarding looks like this in extension.conf [forwarding] ... exten => 511,1,Dial(SIP/sip_proxy-out) ... This will do the re-invite, which is attendance transfer maybe. But I want a blind transfer by REFER method. How can I do that? I know that the transfer() function may be able to do that. But I don't know

Hi, I have been trying to configure my Asterisk to use a Sip provider for out and incoming calls. I only have one user and password for connect to my sip provider. My sip.conf is: [general] ;disallow=gsm ;allow=ulaw port = 5060 ; Port to bind to bindaddr = 0.0.0.0 ; Address to bind to context = default ; Default for incoming calls callerid=No

> Hello fellow asterisk people! > > I have Asterisk listening on port 5061 and SER on port 5060. > > Asterisk is configured as a gateway for ISDN/Analog/H323 and also SIP. > > My problems are with SIP. I can make incoming calls from SIP to asterisk > and to any of the other networks, but when I try to make an outgoing call > from Asterisk to SER I see the following in

Have a question about implementing Call Rollover with my current extensions.conf configuration. [macro-stdexten] exten => s,1,Dial(${ARG2},20) ; Ring the interface, 20 seconds maximum exten => s,2,Voicemail2(u${ARG1}) ; If unavailable, send to voicemail w/ unavail announce exten => s,3,Goto(default,s,1) ; If they press #, return to start exten =>

Almost two years ago, a change between how AEL code is built into Asterisk dialplan between minor versions made clear the need to provide a sane entry point into AEL subroutines and that's how AELSub() born. With Asterisk 11 release, they way [stdexten] at extensions.conf is invoked changed from Macro to Gosub using the 'missing context feature' and this caused that any stdexten