similar to: Don't enter a queue if no one is logged in

I'm trying to see if this is even possible. When you dial ext 2000 I want it to ring my sip phone for 20 sec then call my cell and let it ring for 10 sec if I do not pick up the call on my cell I would like it to go back to * and leave a voice message for me. Here is what I have so far in my extensions.conf Everything works except the call will not go back to * after the 10 sec rule has

I'm trying to set up the Music on Hold feature. However, when I place a call the moh starts and stops immediately and as a result I dont hear the audio. -- Started music on hold, class 'default', on channel 'SIP/XXX' -- Stopped music on hold on SIP/XXX NOTICE[380]: res_musiconhold.c:515 monmp3thread: Request to schedule in the past?!?! My extensions.conf reads: exten

Hi all, I have the Asterisk set up and 2 softphone (Xlite) set up on two other PC. With the following configuration, I can use one softphone (2000) to call the other one (2001) and/or the voicemail at 2999. Here is my problem: 1. When I dial 9+nxxx-xxxx with one of the softphone to the PSTN via X100P card, I got busy tone. (i.e. I want to use the phone line which is connected to the

I have put together this call forwarding and dnd config: I'm sure it can be dome with macro's but I couldn't figure that out... anyone care to input. 74 Turns DND on my phone will not ring, drops caller to voicemail... 73 Turns DND off 72+ext forward your extension to another extension and voicemail is left at the forwarded extension. 71 turns off call forwarding. ; dnd Could

I have a voicemail application that users can listen to messages and leave messages. I am looking for a way to play a beep tone to a user when a new message is received when they are on the phone. Here is what I have come up with: in extensions.conf: [beepvoicemail] exten => 1000,1,answer() exten => 1000,2,NoCDR() exten => 1000,3,wait(2) exten => 1000,4,Set(TIMEOUT(absolute)=5)

I posted a problem earlier thinking it was due to a lack of sound card. Several members stated that you do not need a sound card to play audio to a PRI channel. I did some further testing and discovered that there is a problem with call progress tones or signaling on my PRI. I think that the reason I am not hearing audio from the MeetMe() or Playback() apps. is because the the calling side of

Hi Folks, I am newbie to asterisk. Recentely I have installed asterisk on Linux Fedora 2 box. After reading some document, I tried to configure the server. When I connect to our server, SIP user-agent shows that I am logged in. But it doesn't show my system(client) IP when I issue command at astrisk CLI. The O/P is as below. *CLI> sip show peers Name/username Host

I have just installed * from the latest CVS and I can make calls via X-Lite to outside numbers but for only 30 to 35 Seconds at a time then Broadvoice will hang up on me but X-Lite will not know it. Once I hang up X-Lite then I will get the following error message: Spawn extension (default, Number-I-Dialed, 1) exited non-zero on 'SIP/200-6a22' -- Got SIP response 404 "Not Found"

Are there any phones whose display can show queue statistics, ie: calls waiting, etc, on the phone itself without too much trouble with Asterisk? Especially while the phone is in use (on a call)?

I am just starting out with * so bear with me please. I have tdm400p with 4 fxo modules on it. When I call into the asterisk box from my mobile, I can see the asterisk console picks the call up and routes it to my computer with x-lite. There was no sound coming from either - just silence. I then decided to route it directly to voice mail to see if that would narrow the problem down, but it

Hi all, Any one tried installing Asterisk on Linksys WRT54G? We have but facing problems with SIP to SIP calls. The phones ring and calls are established but we cannot hear any voice at all. I tried allow=all in the general section but did not work. So I forced ulaw. Can any one please check it out and let me know what is wrong? Here are the conf files: Asterisk Version: Asterisk

Hi, I configured asterisk on redhat linux 9 box. I installed two different ip softphones (SJPHONE and X-PRO) and got them registered with asterisk. The call from one phone to another does get routed via asterisk, but there is one problem coming up. As soon as call is accepted by the end user , it is automatically disconnected with the error "cannot align media streams". If I enable SIP

I have a few SIP phones, Cisco 7960s, and was looking into implementing some compression, ala G.729. I'm looking into purchasing a g729 licenses just to get an idea of performance and voice quality, over lans, wireless and single channel isdn. Does anyone have positive/negative experience w/ getting licenses/support from Digium? Hows the sound quality compared w/ g.711? Is 729 better

<div><FONT size=2>Hello,</FONT></div> <div><FONT size=2>two questions: </FONT></div> <div><FONT size=2></FONT>&nbsp;</div> <div><STRONG><FONT size=2>1: How can I open/enable network connection to B?</FONT></STRONG></div> <div><FONT

hi do u have the sip phones extensions in the extension.conf and are they in the right context (sip-incoming)??? are the sip phone registering to asterisk?? try stop asterisk and reconnect as asterisk -vvvvvvvc to check see them registering... ________________________________ From: asterisk-users-bounces@lists.digium.com on behalf of Sistemista WebSolvingJaa Sent: Fri 7/1/2005 6:43 PM

[3000] type=friend dtmfmode=INFO insecure=yes canreinvite=no auth=plaintext host=dynamic allow=ulaw [2000] type=friend dtmfmode=INFO insecure=yes canreinvite=no auth=plaintext host=dynamic allow=ulaw i have declared these two users 3000 and 2000. they are registering successfully. problem is that

I think I have it configured properly. ztcfg -vv shows it as channel 1 and zttool shows it as OK. But I can't dial out. When I try, it shows it arrive in teh right stack, but then issues the following errors: channel.c:1676 ast_request: No channel type registered for '{PSTN-1}' app_dial.c:554 dial_exec: Unable to create channel of type '{PSTN-1}' = = Everyone is busy at

Hi list, i've problems with my * server and the 4 phones which are linked to it. i've 2 grandstream bt100 with the firmware upgraded to 101, a wi-fi phone (i don't know its brand) and another ip phone i don't know its brand. with this sip.conf : [general] port = 5060 bindaddr = 192.168.100.229 context = default ;x changed from default to sip localnet = 192.168.100.0/24

Hi all, Someone know how can I check for available members on a queue Before I queue the call, so I can do something else with it? Note that is not the case for joinempty Thanks, Gabriel Ortiz -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20090718/462b725b/attachment.htm

I testing gluster (the downloadable vmdk) under VMware Vsphere (ESX 4.0). The screen size is stuck at 800x600. I've tried increasing the size in the guest settings for vmware but that doesn't help. Some of the command buttons are off the screen and are inaccessible.