similar to: Can Asterix seperate the signalling and the media ip's with Quintum

Hi Guys, I know no doubt this has been covered on the list a zillion time before, but can anyone point me to some good resources on using Asterix as a VoIP gateway? I would like to get two TDM400P cards in two machines attached to separate adsl connections (in two different physical locations). I'd then like to be able to plug POTS telephones into each of them (I understand I will need FXS

Hi , I am a newbie with Asterix and not sure if Asterix is a right tool for my needs. Let's suppose this scenario : I have a telephone line in one office( all calls are paid to telephone operator). In other offices I have only internet connections. Is it possible to use Asterix so that I can make telephone calls from ALL offices( without direct telecom connection) ? if so, what telephone

Hi, I've been having some problems with my internet connection, it cuts out for aprox 30 seconds at a time and after that i have to do a reload in asterix for it to re-register my sip account with broadvoice otherwise it won't accept any connection till i reload, is there a way for it to automatically re-register or am I missing something else ? Thx. Armand

Hello, I try configuring Quintum DX gateway as link to PSTN for *. Now, I can dial number which is connect to Quintum, and call is diverted to *. I don't know what I should set, if I want call from SIP_phone registred in Asterisk to PSTN via Quitnum. I set in sip.conf account for Quintum [sip_proxy-out] type=peer outboundproxy=QUINTUM_IP , and changed extensions.conf. When

Hi, I'm having problems to register Quintum Tenor DX 3020 on a Asterisk box with SIP. Asterisk always returns "Username/Password mismatch". I've tried all configurations that was on the Quintum's manual, but no success. I've tested the same username and password with a Linksys (PAP2-NA) with the same asterisk box, and it worked fine. Where is the problem ?

Hi all, Can someone share with me his experience in making asterisk-oh323 talk to quintum gateway without gatekeeper. My set up is QUINTUM GATEWAY ------IP----M ASTERISK (OH323) Both are gateways.. but I don't know what authentication I will set up in oh323.conf and how to set it up I will be glad if anyone can help Goksie

Hello *'s, I have question regarding Quintum Tenor AXT800 VOIP gateway can anyone integrate it with asterisk if anyone what is the scenerio i have scenerio which is quite simple but i am confused about it whether it is possible or not : I integrate it with asterisk for interanet no PSTN at all just only IPphones and analog phones connected on FXS port.Is it's neccassary to cannect with

Hello, My colleague installed a Asterisk home as company's SIP server and I would like to integrate the Quintum gateway (SIP) but the calls don't get through. Bellow is are the configurations on each side: Quintum ******** Primary Registrar = 202.69.190.244:5060 Primary Registrar User Name= sipquintum Primary Registrar Pwd= sipquintum Primary Proxy =

Hello *'s, I have question regarding Quintum Tenor AXT800 VOIP gateway can anyone integrate it with asterisk if anyone what is the scenerio? i have a scenerio which is quite simple but i am confused about it whether it is possible or not : I integrate it with asterisk for intranet no PSTN at all just only IPphones connected through ehternet port and analog phones connected on FXS port.Is

Hi, I have an asterisk and a quintum AFT200 with two FXO ports, and want to use it as a gateway to handle outgoing and incoming calls. I have found this thread, http://lists.digium.com/pipermail/asterisk-users/2005-February/084015.html But I think I need a little more help, could anyone knows where I can find the basic configuration for this quintum to get it connected to Asterisk using SIP, no

Hi All I'm trying with no luck to connected the Quintum D series Gateway with the new SIP release to asterisk. Have anyone done this? If yes then how should I configure the sip.conf to accept the registration? maybe a sample config? Thanks /Krystian

Hi, when trying to start Asterix XXL with wine, I get the following error messages: fixme:d3d:IWineD3DImpl_CheckDeviceMultiSampleType Quality levels unsupported at present fixme:d3d:IWineD3DDeviceImpl_GetAvailableTextureMem (0x1a5738) : stub, simulatin g 64MB for now, returning 64MB left fixme:d3d:IWineD3DDeviceImpl_SetSamplerState sampler 7 type WINED3DSAMP_MINFILTE R(6) is out of range

Hi All, Is it possible to use Quintum AFT800 on Asterisk 1.4.29 as Trunk for Analog (like Digium Analog Card) ? And if it's possible, could any one please give me the reference how to configure it on Asterisk 1.4.29. Thanks Regards, Zoel Hairi -------------- next part -------------- An HTML attachment was scrubbed... URL:

Well the subject line probably says it all. I have a Quintum D3000 which I'm supposed to be getting connected up to our Asterisk system. No matter what I try, neither username or authuser config works. I've also tried md5auth and it still refuses to register. Any one have a config they could share with me? Any help would be much appreciated. Neil

Please has anyone on this list had experience with getting Quintum equipment to talk to Asterisk? Specifically a D3000 in my case. It is refusing to register and I'm out of ideas. Any help appreciated. Neil

Hi, just wondering if there is anyone that can help me configure my quintum box to operate with asterisk. i have tried and made numerous attemtps configuring the tenor to work with asterisk@home but have been unlucky. anyone out there has a cheat sheet to configure this device. thanks.. for some reason i cannot get it to work. your help is appreciated.

Hi. I'm trying to configurate Quintum AX to work with Asterisk SIP egister/Proxy server and my problem is that only the first user account get logged in and only that user is able to make call correctly. It seems to be a problem with authorization - I have noticed no "Proxy-Authorization" information in SIP INVITE, ACK, CANCEL messages. I have also noticed that when I remove

I just upgrade quintum A800 with new SIP firmware ---------- Product Name: Tenor Analog A800 Multipath Switch - 8 ports (Rev. B) Gatekeeper Status: Mini GK Calls Allowed: 8 Feature Bit Status: -PS/+RB/-ER Languages allowed: 1 Serial Number: A002-00308F Ethernet Address: 00-30-E1-00-30-8F IP Address: 10.101.0.10 Subnet Mask: 255.255.255.0 Default Gateway: 10.101.0.1 System Software Version:

Does anyone have any instructions on how to connect a Quintum AS200 to Asterisk as a SIP phone? I currently have the AS200 sitting in a remote office and would like to use it as a SIP phone. It would register with Asterisk. Overall, I've had problems getting this work but I'm hoping that someone on this list might have some experience with this!

<!DOCTYPE html PUBLIC "-//W3C//DTD HTML 4.01 Transitional//EN"> <html> <head> <meta http-equiv="Content-Type" content="text/html;charset=UTF-8"> <title></title> </head> <body text="#000000" bgcolor="#ffffff"> <font size="-1"><font face="Helvetica, Arial,