similar to: Monitor doohicky got event Event 160 on channel..

hi all, i have an asterisk install with a digium 4 port fxo card and cisco 7960 sip phones -- running on a compaq Pentium III (Coppermine) at 800Mhz 256KB cache and 1GB of ram. when a call comes in on zap/1-1 for example, the delay between when zap sees the line going to ring state, and when the desktop telephone rings can be as long as 7000 milliseconds (or about 3 or 4 rings on an ear piece).

I installed Trixbox and a TDM400P with 2 FXO and 2 FXS ports and am having an annoying issue with the FXO ports. As soon as I plug either one into the phone line it's as though the line is disconnected i.e. get disconnected tone when trying to dial out, line is busy when dialling in. The CLI shows the following: trixbox1*CLI> zap show channel 4 Channel: 4 File Descriptor: 18 Span: 11*

Howdy, New installation, trying to connect an RBS T1 with AMI/D4 framing and E&M Wink. Using a Sangoma A102d and asterisk 1.4.22-2 on Centos5 (Trixbox 2.6.2.1). Outbound calls work fine, but inbound calls fail to read the DID information, and with debug set to 10 I get the following: [Feb 2 19:40:23] DEBUG[25184] chan_zap.c: Monitor doohicky got event Wink/Flash on channel 3 [Feb 2

Hi all, I must admit that I am stuck. I have a TDM400P card with two FXS and two FXO modules which I had set up and configured so that it was working beautifully. The only problem was that occasionally it would get itself into a state where outgoing calls would simply be met with a very loud static. A reboot would fix this issue and everything would work fine for a while. Recently however,

hi,all i have just set up asterisk 1.6.0.7 rc1 with spandsp 0.0.5 pre4 to ReceiveFAX, link to a E1 (DE410P) using dahdi this can receive the fax from E1 successfully, but i see many error message in the log like this: [Mar 16 09:24:38] ERROR[23540] channel.c: ast_read() called with no recorded file descriptor. when i receive a 5 pages fax, i will see this error message over 200 lines..... it

I'd like to have my Asterisk system pick up a certain extension on an existing Panasonic PBX when it rings. (It's connected to some proprietary Panasonic doorphones that I haven't replaced yet.) I connected that extension to an FXO port on a Digium AEX410 card, and set that channel to have the context "doorphone". The problem is that the extension is never executed. With

Hi all, I have 1 Card Digium TE412P and 2PRI E1. I have more problems with drops lines. The asterisk log is this: May 16 10:52:26 NOTICE[4465]: chan_zap.c:8194 pri_dchannel: PRI got event: Alarm (4) on Primary D-channel of span 1 May 16 10:52:26 WARNING[4465]: chan_zap.c:2287 pri_find_dchan: No D-channels available! Using Primary channel 16 as D-channel anyway! May 16 10:52:26 NOTICE[4465]:

Hi, Continuing with the saga of Digium vs MTNL Mumbai, looking for suggestions on handling incoming Caller-ID issues. The card manages to grab a couple of (random) digits of the incoming CID, but they're more or less useless. Is there any way to fix this? Asterisk 1.8.13, Dahdi 2.5.0.1 on Debian Testing (Wheezy), MTNL Mumbai. Digium, Inc. Wildcard AEX410 4-port analog card (PCI-Express)

I am getting: NOTICE[180235]: chan_zap.c:7358 pri_dchannel: PRI got event: 6 on Primary D-channel of span 1 on my asterisk box and it seems to be causing a poping sound in the phones, I am wondering if anyone can shed some light on this. I have scanned the archives and get possibilities ranging form motherboards, to pri, to loaded module problems. Can someone tell me the best way to start

I receive this error on the asterisk console and it is pretty much ALWAYS coming up. Sometimes there will be a break where it does not display. We had our PRI provider test the lines and they claim that there is no signalling problem. It doesn't matter if there are no calls or if there are 10 calls in progress the error is still displayed. I also get an annoying popping or clicking sound

Hello, Talking with Soren Sratje about Caller ID in Brazil, we compare ours DTMF tones captured by ztmonitor. wcfxo correctly recognize the "DTMF CLIP" and asterisk shot the AST_STATE_PRERING correctly. But the DTMF tones are not reconized. In the chan_zap.c, the code: if (f->frametype == AST_FRAME_DTMF) { (...) Does not occurs because the frametype is always reconized as voice

Hello, my configuration is the following: a TDM400P board with an fxs and fxo daughter boards on it. I thus connect a fax to my FXS port, after having verified that this port was correctly functioning. For this, I had tried before with a simple phone, and with some basic voicemail exten scripts. Here is my simple dialplan for my fax reception: exten => 300,1,Ringing() exten =>

Greetings. Today I've installed a fresh new E100P on a EuroISDN PRI. It seems to work well, accepting calls, but, when I start *, I have the screen flooded with this message: PRI got event: 8 (or 6) If i look into /var/log/asterisk/messages i've this Error: File chan_zap.c, Line 5341 (zt_pri_error): PRI: Read on 35 failed: Unknown error 500 Repeated indefinitely. Also, i've a

Hey, all. I'm seriously thinking about doing the VoIP thing at home. The perfect platform seemed to be the Sheeva "wall wart" (http://www.marvell.com/products/embedded_processors/developer/kirkwood/sheevaplug.jsp). It's a cute little doohicky with USB, SD-card, Ethernet, and runs on an ARM CPU. I'd like to avoid SIP to my provider, just 'cause it's always such a

Hi, I facing a problem with flash hook. When ever I do a flash hook to place an extsing call on hold, the call gets disconnected. The debugs on Asterisk shows that 'on hook event detected' when I press the flash button on the phone. The setup is like this Asterisk box with T1 cards and FXS cards. The T1 card is connected to an IAD and configured for ISDN PRI lines. Analog phones come

Hi list, Just installed spandsp. In my limiting testing, I have an issue on a Philips fax machine (HFC21) directly connected to my * server through TDM400, reception with rxfax works fine, but txfax always fails. Below is a transcript of failed transmit. This is with asterisk-1.0.3 (with native moh patch but I don't think it is the source of the problem). I already tried libtiff 3.5.7,

Hi, I have a problem that is biting at all my customer sites where they have PRIs taking heavy load. This happens both with the stable code stream and with the current CVS. What happens is that after some running, Asterisk starts reporting strange errors on the PRI, eventually calling the PRI down Starts with this sort of thing: Feb 21 09:39:23 DEBUG[18095]: Didn't get a frame from

Hello to all, I have a strange problem with my asterisk. Line drops while i am in a call and without a reason.The line drops no matter if it is a incoming or outgoing call and it happen while i am talking on the phone (no silence detection problem). I tried to debug the situation and the only strange thing is the "got event On hook" (i guess..). I am thinking that it is a problem

Hi all, I've been running Asterisk with a TDM400P for about 6months, no problems. 2 in/outgoing analog lines, one analog phone. Recently I was messing with the XTEN client, got to finagling with things, and not knowing what was wrong I upgraded from 1.0.7 to 1.0.9 (both asterisk + zaptel). I was testing various things, and found everything worked except outgoing calls. So I checked

Hi Guys, Running the following with a Sangoma A101D PRI card: *Asterisk 1.4.21.2* *LibPRI version: 1.4.10* No inbound or outbound calls can be made. In fact Asterisk CLI doesn't show any activity. Problem goes away on restart of the system or maybe asterisk. I see post about upgrading Libpri to 1.4.10.2 and then I see posts that even that didn't work. Anyone can weigh in this please?