similar to: chan_mISDN module does not load

Hello. Just installed the Beronet BN4S0 card. But i can't connect to my ISDN Line. misdnportinfo gives (what does ":Layer 4 protocol 0x04000001 is detected, but not allowed for TE lib" mean?): best regards and thanks t. asterix asterisk # misdnportinfo Port 1: TE-mode BRI S/T interface line (for phone lines) -> Protocol: DSS1 (Euro ISDN) -> Layer 4 protocol 0x04000001

Hi list, I installed a fresh Debian/Etch with Asterisk 1.4 and Zaptel 1.4 from SVN for 2 Digium B410P card. I ran configure in Asterisk dir, went in zaptel dir and: make, make install, make b410p. Everything is ok. Now I want to compile Asterisk but can't activate the chan_misdn channel which depends on -from menuselect- isdnnet(E), misdn(E), suppserv(E) When I made the make b410p, all

Hi, Since a week ago I am trying to get chan_misdn working with asterisk 1.4.19, using HFC based ISDN card on Linux 2.6.22. My setup is done as detailed on wiki and FAQ. * mISDN and miSDNusers are 1.1.7.2, unpacked, build and installed. After installation and misdn-init, I have this: aragorn:root/pts/1: # misdnportinfo Port 1: TE-mode BRI S/T interface line (for phone lines) ->

Hi, I am struggling to get plain Cologne chip cards to run in NT mode, runs nice in TE mode despite the error message: login as: root root at 192.168.2.22's password: Last login: Tue Sep 1 23:09:24 2009 from 192.168.2.50 Welcome to Elastix ---------------------------------------------------- misdnportinfo Port 1: TE-mode BRI S/T interface line (for phone lines) -> Protocol: DSS1

Hi all, I have a problem with my beronet card with 2 isdn. I think drivers and Asterisk are ok but the red led on the card always blinking. The card is connected with PBX. I post some conf: [root@gateway ~]# misdnportinfo Port 1: TE-mode BRI S/T interface line (for phone lines) -> Protocol: DSS1 (Euro ISDN) -> Layer 4 protocol 0x04000001 is detected, but not allowed for TE lib. ->

Hi all, Does anybody of you have the winbond w6692 working with the mISDN/chan_misdn.so? When loading chan_misdn.so from Asterisk, I get a "No lower Id port:1" error. The /var/log/messages file says: "MISDN free_device: entitylist not empty" I'm using Linux 2.6.11.11 + mISDN-CVS-2005-05-01 + Asterisk 1.0.7 + Zaptel 1.0.7 chan_misdn build from chan_misdn-beta-0.0.3-rc6

Hello ! I would like to get working a Fritz PCI card using chan_misdn operating in ptp mode. Afer compiling mISDN into the kernel and building chan_misdn Asterisk stops loading with : [chan_misdn.so] => (Channel driver for mISDN Support (Bri/Pri)) == Parsing '/etc/asterisk/misdn.conf': Found UnLocking config_mutex == Registered channel type 'mISDN' (This driver enables

Hello, list a have a problem i can start asterisk, i get the fowlling error: [chan_capi.so] => (Common ISDN API for Asterisk) == Parsing '/etc/asterisk/capi.conf': Found Feb 11 13:50:36 NOTICE[2535]: chan_capi.c:2636 load_module: CAPI not installed! Feb 11 13:50:36 WARNING[2535]: loader.c:345 ast_load_resource: chan_capi.so: load_module failed, returning -1 Feb 11 13:50:36

hello, i have a problem on started asterisk, when try to start asterisk a get the fowlling error: chan_misdn.so] => (Channel driver for mISDN Support (Bri/Pri)) Feb 17 11:34:01 WARNING[3104]: config_old.c:27 ast_load: ast_load is deprecated, use ast_config_load instead! == Parsing '/etc/asterisk/misdn.conf': Found Feb 17 11:34:01 WARNING[3104]: config_old.c:39 ast_destroy: ast_destroy

Good Evening, The company I work for is attempting to connect an Cisco ISDN Router to an OpenVOX B200P BRI Card so that we can get it to dial out across an existing ISDN PRI Line also installed in the Asterisk PBX Everything has compiled successfully and the BRI card has been detected when mISDN is started: # misdnportinfo Port 1: NT-mode BRI S/T interface port (for phones) -> Interface

Hello everyone, I have been using an AVM Fritz! card with chan_capi and mISDN for quite a while in PTM mode and it was working finely. Now, I needed more DID/MSN, so I switched to PTP. But now nothing works anymore :( I am using Asterisk on Debian Sarge stable and installed Asterisk along with chan_capi from apt-get. I installed mISDN from the CVS of isdn4linux.de. It is : - Asterisk

I'm using avm fritz card usb with kernel 2.6 patch with mISDN. The module is load correctly when I type lsmod I've got the following output: Module Size Used by zaptel 178308 0 avmfritz 21388 0 mISDN_isac 14336 1 avmfritz mISDN_dsp 191424 0 l3udss1 34184 0 mISDN_l2 39040 0

HI, I tried to install asterisk and mISDN via http://www.asterisk.org/downloads/yum My machine is running with kernel-2.6.18-164.15.1.el5.i686 # grep kernel /var/log/yum.log Mar 21 16:09:28 Installed: kernel-2.6.18-164.15.1.el5.i686 Mar 21 16:09:42 Installed: kernel-devel-2.6.18-164.15.1.el5.i686 I've installed the following packages: # yum install asterisk16-misdn mISDN mISDNuser

Hi All, We've got msidn configured: Port 1: TE-mode BRI S/T interface line (for phone lines) -> Protocol: DSS1 (Euro ISDN) -> childcnt: 2 -------- mISDN_close: fid(3) isize(131072) inbuf(0x8fd5060) irp(0x8fd5060) iend(0x8fd5060) and running on Asterisk 1.4.21.2: pbx*CLI> misdn show stacks BEGIN STACK_LIST: * Port 1 Type TE Prot. PMP L2Link UP L1Link:UP Blocked:0 Debug:0

Hello I have just set up Asterisk Asterisk 1.4.21.2 on a CentOS 5.2 machine. I am using the OpenVox B200P ISDN card. My problem is that even though chan_misdn module seems to be loaded correctly with Asterisk (I can see it using 'module show' command) the misdn commands are not available to me in the CLI so I cannot tell if my box is correctly interfacing with the ISDN card Any ideas

Hello, I have problem with capi, I can't install it. I have putted all info what I did and what I get :). I think you can suggest me how to solve this problem.and thanking you in anticipation. I have ISDN Frtiz!Card PCI v2.1and I want to install it to my ubuntu box (kernel: 2.6.17-10-server). Using command "lspci -vv" , I can see that kernel finds this card: *02:0d.0 Network

Have you got termination set correctly? I have a B410P working with 2 x NT and 2 x TE ports successfully. I had to turn the 100ohm termination on on the NT ports (even though I have them set as PTP in mISDN.conf). HTH -->> -----Original Message----- -->> From: asterisk-users-bounces at lists.digium.com [mailto:asterisk-users- -->> bounces at lists.digium.com] On

Hi List, I?m having problems compiling chan_misdn: asterisk:/usr/src/chan_misdn-beta-0.0.3-rc4 # make install cc -ggdb -Wall -D_GNU_SOURCE -Wno-missing-prototypes -Wno-missing-declarations -fPIC -I/usr/src/asterisk/include -DAST_CONFIG_DIR=\"/etc/asterisk/\" -I/usr/src/mISDNuser/include -I/usr/src/linux-2.6/include -I/usr/src/mISDNuser/i4lnet/ -Wall -c -o chan_misdn.o chan_misdn.c

Hi all! I'm getting an error when I try to start asterisk with chan_misdn. I patched my kernel (2.6.12.4), and compiled the whole stuff (kernel, mISDNuser, asterisk, chan_misdn). I got mISDN from http://isdn.jolly.de/download/v3.0/ I'm using a CVS Snapshot of asterisk, which was checked out about 5 hours ago. This is the error: [chan_misdn.so]Aug 15 14:13:29 WARNING[4929]:

Hi, My asterisk server was working with a 4-FXO analog card (TDM400P). I recently added two digital cards: a TE120P (1 PRI) and a B410P (4 BRI). The B410P is still unconfigured but inserted in a PCI slot. The TE120P's jumper is set to E1 as it will connect to a commercial PBX's PRI card also configured as E1. My analog channels used to be 1-4 but since I added the new cards I changed