similar to: Digium adaper S101I - IAXy Losing connection

How to configure Digium S101i adapter to work with "pickupexten *8" ? I have few Sipura adapters and "*8" work OK but my new Digium S101i refuses to cooperate. -- #Joseph

I have a few questions with regards to Digium S101I adapter. I would like to use it as a traveling companion, plugging it into various networks (all behind firewall I assume). I'll be registering it into my asterisk server (behind firewall, port 4569 will be open). 1.) If I plug that small adapter S101I into another network will that network have to have port 4569 open as well? 2.) If

Does anybody know what DTMF coding does S101i adapter using? I've been testing one for over a week and here are my observations: - DTMF signaling is working perfectly with Asterisk, much better than Sipura 3K Though, I think the Asterisk "iaxy" firmware is buggy, the unit is using auto-update feature; so I have Asterisk 1.2.13 and iaxy firmware version is: 23 When enable in

Hi, I have three Iaxy devices (s101i) parts. Two of them seem to work fine. The third plays a loud repeating click sound when an analog phone is plugged in. I can provision all of them, and make calls to all of them. The clicking one will blink when a call is incoming, but no audio from the call can be heard on the handset, and the caller only hears silence. The same handset works on the

Is there anyway to control echo on Digium S101I adapter? -- #Joseph

Hi All, I have two old S100 units (the blue ones, not the newer black ones). I am trying to reset these to factory default using the following instructions, but it is not working. Does anyone have any other suggestions to reset this model of the adapter? Tried this: 1. Remove all of the cables, except for the power cable. 2. The factory reset button is next to the RJ45 jack. Press and hold the

I'm having a problem with my IAXy not always connecting to my Asterisk box. When I pick-up the phone plugged in to the IAXy I get a busy signal. I have to hang-up the phone and wait a few seconds after the orange LED goes out and then try again. When this happens I don't see any connection attempts in the Asterisk -r output. When I do get the IAXy to connect to Asterisk I get a

Hi, I'm having an issue with a soekris net4801 board and a S101i "IAXy" device. When I connect a successfully provisioned IAXy directly via a crossover cable into an ethernet port of the soekris, the link led turns on orange so i'ts 10Mb and the activity led blinks like if there is some action going on but when I try 'tcpdump -nettti sis1' I see nothing going on, no

Hi.. I have to setup an extension in a remote location that will use a cordless analog telephone.. I am looking at the IAXY to do this for me..Basically the data path will be as follows... [Asterisk] == (NAT) == {Internet} == (NAT) == ATA -- Handset Since there are two NAT boxes in the path I know SIP won't work.. I also don't want to move the Asterisk box to the internet side of the

Hi. Does anyone know about a simple one-fxs ATA with pulse dialing support that can work with Asterisk? A SIP one would be ok. I've been told that the Digium S101i IAXy does support pulse dialing; although it's a iax2-only ata it could be enough. I need a bunch of them to convert some old fashioned rotary phones into VoIP ones (I'd like to disassemble the ATAs to remove the boards

On Tue, Dec 23, 2014 at 6:34 PM, Rusty Newton <rnewton at digium.com> wrote: > On Tue, Dec 23, 2014 at 4:17 PM, Joseph <syscon780 at gmail.com> wrote: >> Are there any adapters that would allow me to connect asterisk to wifi or we >> are not there yet? >> I have Digium adapter S101i that was discontinued but similar device that >> would connect to wifi

Are there any adapters that would allow me to connect asterisk to wifi or we are not there yet? I have Digium adapter S101i that was discontinued but similar device that would connect to wifi network and a cell phone would be handy. -- Joseph

That little Digium adapter S101I is a nice and compact (good for travel) but has a serious limitation, it doesn't support bridging. If I have four/five of these units registered to my asterisk server (over the Internet) and with standard DSL or Cable connection all for of them connected and in use (utilizing G711); my upload bandwidth will get saturated as all of them have to go via my

Digium has discontinued their ATA iaxy adapter; don't blame them, too expensive so they can not compete. The adapter is upgraded automaticaly when it is connected to new asterisk version; since this adapter is discontinued will it still work with asterisk 1.6 and beyond or will it be\ just a "door stopper"? -- Joseph

I was just browsing Digium's web site and noticed they are taking orders for the new IAXy. Has anyone purchased and tested one of these yet?? I have thought about buying one for testing, but want to make sure it isn't going to be a flop like the last one. Robert

Are there any cell phone (gadgets) that can be connected to standard switch phone network? (ability to check email would be a plus). Digium adapter S101i can be connected to any network and it allow a standard phone to act as your local extension over the Internet (by registering to asterisk), it works "almost" perfectly. So it would be handy to have a cellular phone that can be

I need a cheap simple adaptor for analog phones to use with Asterisk. It should be some kind of "configure and forget" type of device, to use at the office, or just throw it in a road warrior's bag and use it while travelling, to call back to the "mothership". I can't decide between iaxy and sipura. Can you guys help? Which one would you use? (and why?) I feel that iaxy

I've been told by someone at Digium that they discontinued the IAXy ATA. I was buying the X100P IAX ATA for some time until even they discontinued that. I am looking for a new ATA that does IAX2 and supports the following codecs: GSM, Speex, G711 Can anyone point me in the right direction? I'd prefer to stick with IAX protocol because it is easier to use working with NAT and SIP/NAT is

Hi, hoping that experienced hands will quickly show me the right way: after a fruitless web search i am turning to this list with my rather elementary question: is there any other way to communicate with the IAXy besides using special utility software that needs to be compiled under UNIX? Here is the story: about two months ago, after some not very satisfactory attempts at using SIP (my phone

On 12/23/14 18:35, Rusty Newton wrote: >On Tue, Dec 23, 2014 at 6:34 PM, Rusty Newton <rnewton at digium.com> wrote: >> On Tue, Dec 23, 2014 at 4:17 PM, Joseph <syscon780 at gmail.com> wrote: >>> Are there any adapters that would allow me to connect asterisk to wifi or we >>> are not there yet? >>> I have Digium adapter S101i that was discontinued