similar to: Asterisk with 2 Public IP-Is it possible?

On Mon, May 22, 2017 at 11:03:30AM +0200, Keith Whyte wrote: > I have two tinc nodes (A and B) behind a firewall > > NodeA and NodeB have 192.168.1.2 and 192.168.1.3 assigned on an internal > LAN, and they both have different public IP addresses forwarded to them, > port 655 udp/tcp > > I would like any given node in the C-Z group to be able to find Node B > on it's

AFAIK, and my setups thus far, unless you have NodeB’s public key in Nodes C-Z (with NodeB’s public/reachable IP configured in Nodes C-Z) *and* you have the PublicKeys for NodesC-z configured in NodeB, there is no way that NodesC-Z will be able to establish a connection directly with NodeB, and it’ll have to forward via NodeA (or any other node that do have a direct connection established with

I did notice the that interface we have named br-lan did not have the proper broadcast and netmask information. I adjusted that and it looks like its now connecting but still running into issues. Here is a snipet from the new system we are trying to connect in (from the /var/log/tinc.log file) 2018-03-15 22:57:26 tinc.NETNAME[871]: Read packet of 74 bytes from Linux tun/tap device (tun mode)

Hi all I feel like I should know the answer to this question, like I read it someplace sometime, but it evades me right now. It's also an opportunity to say hello to the list and many thanks for writing and supporting tinc vpn! We make great use of it at rhizomatica. So, Let's take this example setup. I have two tinc nodes (A and B) behind a firewall NodeA and NodeB have 192.168.1.2

On Wed, December 23, 2015 8:06 am, Meikel wrote: > Hi folks, > > I have a server at Soyoustart.com (which is a brand of OVH). I run > CentOS 6.7 and have problems with network configuration. > > I want to add a second public ip (failover ip) to the server and did > follow the instructions in the CentOS-section of > http://hilfe.ovh.de/AdministrationIpAliasHinzufuegen >

Hi, I'm thinking of introducing Asterisk on Linux for IP PBX. Now I'm using ISP that has VoIP service and I have VoIP terminal box for that ISP and a SIP account for SIP server of the ISP. Now, what I would like to do is the following. A. Setup IP PBX on Linux by using Asterisk. B. For IP-PSTN gateway, configure Asterisk to use my ISP's SIP account and connect to my ISP's IP

Hi folks, I have a server at Soyoustart.com (which is a brand of OVH). I run CentOS 6.7 and have problems with network configuration. I want to add a second public ip (failover ip) to the server and did follow the instructions in the CentOS-section of http://hilfe.ovh.de/AdministrationIpAliasHinzufuegen After executing the required steps I'm not able to reach the host via the second ip

Hi, Currently my Xen server is working like a charm. I use Xen 3.2.1 with a Debian Etch Dom0 and Etch DomU. The VM have access to the network/internet using NAT. Each VM is given a virtual network interface and a private IP 10.0.0.x. What I would like to do know is that a VM can be directly accessible from another public IP. So my physical server is at 91.121.xx.xx. My VM is at 10.0.0.1 (on

I can't seem to figure out how to setup a public IP for the VM so we could use it as a second public webserver. The host machine runs our primary webserver with CentOS 6.9 and one public ipv4 address configured on physical interface eth0. Now i have configured a new bridge interface br0: DEVICE=br0 TYPE=Bridge BOOTPROTO=static The IP settings are for a second public ipv4 address in the

pc1(LANa) ----poor connection ----> VPS <--------- PC2(LANb) pc1 and pc2 used to connected directly with tinc, since pc1 used to have WAN IP(pppoe), but the pppoe IP is not WAN IP anymore (ISP changed to let all ADSL user in a LAN). if I let the two pc connect to a VPS with tinc, can later connections between pc1 and pc2 be directly ? for example, ssh from pc1 to pc2 but not proxyed by

Hello All, I have an Asterisk server v13.1.0 running on EC2 and I am able to connect and register SIP devices and "see" them on the asterisk CLI. I am also able to place calls, but I am not able to hear any audio on either end after the call is picked up. I was wondering if you can tell me what a minimal configuration for Asterisk on EC2 looks like. My current pjsip.conf configuration

Hello, I am trying something crazy here. I have gone through the old archives, lartc.org and lot''s of documentation, but still something is wrong. Here is the situation; The server is Fedora core 2 running kernel 2.6.5 I have 2 uplinks to two different ISP''s. (It will be 3-4 in the future). These ISP''s should serve the bandwith to local clients with multiple subnets.

Hello List, This is our setup which we are trying in a couple of our remote offices: +---------------------------------------+ +-------------------------------------------------------------+ | | | | | +----------------+ |

OK. I think I found the issue. The key is to add rtp_symmetric=yes Here's what my final configuration looks like: [transport-udp] type=transport protocol=udp bind=0.0.0.0 ;; for within EC2 local_net=172.31.32.0/20 ;; For softphones within EC2 local_net=192.168.1.0/24 external_media_address=<publicIPOfEC2Instance> external_signaling_address=<publicIPOfEC2Instance>

If understand the setup correctly based on previous emails, it looks like this: [Internet] <-> [202.172.122.211 (eth1) {Gateway Machine} 202.172.122.74 (eth2)] <-> [202.172.122.75 (eth1) {Other Machine}] So, according to your emails, your external (eth1) interface on the Gateway machine ** needs to be .209 not .211 or .210 ** (as this is where the ISP''s

Hi, I have a failover configuration. The domain controller's IP: 10.23.14.150 as dc01 The failover IP is: 10.23.14.155 as dcha I added an A and a CNAME record to the dns for the failover IP. It is working, i can see the shares, but I could not enter to any share as user, as Administrator it works. I tried to add the interface variable (i am not sure this is available in samba4), that

Hello, I have configured a load balancing router using Julian''s patches and as described in "nano.txt" for two ISP links as shown below. ISP 1 ISP 2 . . | | | | | | | WAN

On Thu, Apr 16, 2015 at 10:09:05PM +0200, Raimund Sacherer wrote: > At first I really like the idea of having 3 Daemons on the headquarter, one for each ISP. The firewall should forward the port 655 from each ISP's public IP Address to my internal server and to the ports 655, 656, 657 respectively [...] > My question now is, for every tinc daemon I need a tun or tap device, so how

Hi,i''m newbie with shorewall ... Currently i have a box with 2 ethernet cards and ppp0 dial up, one of the ethernet cards is plugged to my Cable modem , my ISP provider gave me a private internet IP, so i have to contract a dial up service to get a public Internet IP in order to run some servers. So i was wondering if it is possible make some kind of NAT to tell my box that

Hello, I have a T100P card on a Red Hat 8 machine with Asterisk installed on it and I'm trying to get the data routing properly through it. I purchased an Integrated Data/Voice T1 Line with channels 1-6 voice and 13-24 data. The line is plugged directly into the Asterisk machine's T100P card. Previous to the asterisk set up we had an Adtran router that connected everything to what the