similar to: Zapata, Junghanns Card and a leading 0 on inbound calls

Hi, after a few of upgrades, I noticed these messages in full debug log: Jun 21 12:58:11 WARNING[27273] chan_zap.c: Ignoring switchtype Jun 21 12:58:11 WARNING[27273] chan_zap.c: Ignoring pridialplan Jun 21 12:58:11 WARNING[27273] chan_zap.c: Ignoring prilocaldialplan Jun 21 12:58:11 WARNING[27273] chan_zap.c: Ignoring overlapdial Jun 21 12:58:11 WARNING[27273] chan_zap.c: Ignoring

Hi all, I've been batting my head against a brick wall for the best part of the day and still haven't got any further (apart from getting a big headache, that is). I've searched the Wiki and Googled the hours away, but I still can't find supportive documentation. I've just replaced my ISDN Fritz!/chan_capi setup with a HFC/Zap configuration and had the following problems: 1

Hello, I recently bought a Junghanns Octobri Card. I have some problems with this card to make outbound calls but I can receive calls. I have 3 lines to PSTN and 3 lines to my existing PBX FRANCE TELECOM <-- OctoBRI --> Asterisk 1.2.4-BRIstuffed-0.3.0-PRE-1h <-- OctoBRI --> PABX e-Generis <----> ISDN Phones |

hi. could somebody explain how exactly the following parameters in zapata.conf work: pridialplan prilocaldialplan internationalprefix nationalprefix localprefix privateprefix unknownprefix the wiki & comments doesn't quite explain them. and phone companies are absolutely no help. i've setup systems in the US & China with trial & error until it works. now i'm setting up a

Hi all, i'm trying to install Asterisk with Junghanns QuadBri ISDN card: I have followed all the instructions, and when I run "|ztcfg -tvv" I get | | Zaptel Configuration ======================| SPAN 1: CCS/ AMI Build-out: 399-533 feet (DSX-1) Channel map: Channel 01: Individual Clear channel (Default) (Slaves: 01) Channel 02: Individual Clear channel (Default) (Slaves: 02)

My international calls are not connecting. [general] pridialplan=dynamic ;prilocaldialplan=unknown internationalprefix=00 nationalprefix=0 localprefix= I have the above in my zapta.conf - yet when I dial an international number, I get a ring, then I get the message "the person you are calling, is currently unavailable" This is an ubuntu machine, with a sangoma card, with

Hi list! What exactly is the meaning / function of the pridialplan & prilocaldialplan? I've been trying to find out what the different possibilities for these settings are but couldn't find a clear answer. The possible parameters I could find are are : local,unknown,dynamic,national,international and maybe there are more? Thanks!

Hello all, Recently I purchased an QuadBRI card from junghanns.net after some playing around, reconfiguring dialplans etc with the exception of 1 thing everything seems to work: I seem to be unable to set the outbound callerid. The dutch telecom operator (KPN) provided me with 4 MSN's on 1 BRI interface. In the past years I'm more then used to setting the MSN without the leading 0, this

Hello, I have a problem with the Bristuffed version of Asterisk. I have tried Bristuff-0.3.0-pre-1m,n,o,p (Asterisk 1.2.6 to 1.2.7.1) but they all have the same problem it seems: The setup: A machine with a single hfc-s PCI BRI adapter running Gentoo 2.6.15. Asterisk 1.2.0 (BRIstuffed-0.3.0-PRE-1) installed and working perfectly. Grandstream gxp-2000 as a SIP phone, and a normal mobile

Hello, I have a little problem with signalling. An E100p is connected to an Alcatel PBX, wich has an E1 to the outside. Located in Germany. zapata.conf: switchtype=euroisdn pridialplan=local prilocaldialplan=local overlapdial=yes signalling=pri_cpe .... With asterisk 1.0.2 I can call from a SIP phone to a phone connected to the Alcatel and the SIP number is correctly displayed at the caller.

Hi, When startin * it tells me: ================================ [chan_zap.so] => (Zapata Telephony w/PRI) == Parsing '/etc/asterisk/zapata.conf': Found Sep 3 17:21:59 DEBUG[1076873856]: chan_zap.c:1208 update_conf: Updated conferencing on 1, with 0 conference users -- Registered channel 1, PRI Signalling signalling Sep 3 17:21:59 DEBUG[1076873856]: chan_zap.c:1208 update_conf:

Hi all, I really hope that you guys can help, because I've been tearing my hair out for the past 5 hours on this one. I have a Zaphfc (BRI) card in TE mode connected to the S-Bus of a Nortel Meridian phone system. Phone calls from the Nortel to say MSN 510 are correctly being sent to the right SIP phone. When asterisk dials say Zap/g2/224 (a Nortel internal extension) the call goes

Hi, I have Installed * on a DL380 with a Junghanns 4BRI card and 0.0.2 driver. I have 3 BRI lines connected to SPAN(TE) 1,2,3 and 2 Cisco 7960 with SIP image. I am connected to french PSTN (France Telecom) whith Euroisdn signaling. I manage to call SIP to SIP, PSTN to SIP but not SIP to PSTN. Any idea? Thanks Gwenn Gael Marronnier Here is what I get and my configuration...

Hi everybody, I'm facing a strange problem after upgrading Asterisk from 1.0.9 to 1.2.4. Sometimes, when receiving an incoming call from pstn, although my sip phones ring correctly (I've got both softphones and hardware phones), noone can pick up the call. Asterisk CLI shows me that the phones are ringing, then nothing happens, so there's no problem _after_ someone picked up, simply

hi, on our incoming E1-PRI from german telco Arcor the leading 0 for the (area access code in europe) and the 00 (country accescode in europe) are missing on incoming callerids. only prepending a single 0 is not the solution as suggested by some writers on this list, because there is no way to differ between national and international callerids and it's not possible to make the decission

I've got a bit trouble with callerid and zaphfc cards. Basically zaphfc doesn't add the "0" in front of national numbers (haven't tried a international call yet). With chan_capi that allways worked fine, however i had to define the national and international prefixes in capi.conf. Is there something similar in zapata.conf ? Here is my zapata.conf: [channels]

Dear All, Thank you for taking the time to read this post - I am *confused!* as to why my asterisk setup does not work as it should. I have an ISDN 30 connection for telephony, a Sangoma card, and asterisk installed. Incoming calls, and outgoing calls work 100%. Making an international call, results in silence, or the error message all circuits are busy Numbers being passed to the trunk for

Sorry that I wrote in german : Ich benutze asterisk mit dem zaphfc Treiber. Jetzt hab ich folgendes Problem, habe 2 ISDN-Telefone angeschlossen. zaphfc im nt-mode. Anrufe von ausserhalb per sip (sipgate.de) kommen an. Wenn ich aber intern zwischen den zwei Telefonen (Ascom Eurit 30) sprechen m?chte geht das nur wie folgt : Erst die Nebenstelle w?hlen und dann den H?rer am Telefon abnehmen.

hello: thanks for Tzafrir Cohen for dahdi testing. I installed dahdi-2.1-r3c svn code and asterisk1-6 for testing OpenVox B400P and junghans card. i fund that there is bug (i think) to dectect NT or TE mode. actually on the board, i set it as TE mode, but after start wcb4xxp, but it show the port is NT mode. to detect the TE mode, I modefy the code in base.c

Hi All I am having another strnage problem :) When I dialout on any number from asterisk, it use to add a leading zero in dialed number for e.g I dial a number 5832876 and when I check the tracer's result of PSTN switch that shows me call request for 05832876 thats why I can dial NWD and ISD calls but unable to dial local numbers Thanks