similar to: Not able to find the file zaptel.conf after compiling asterisk and zaptel

Hi List; What is the command and where I can write it to block specific code from calls (then no one will be able to place call for any number start by that code)? --------------- Regards ITS IP Telephony and Contact Center Engineer Eng. Bilal Ghayad Mobile: + (965) 9849460 Yahoo ID: bilmar_gh at yahoo.com MSN ID: bghayad at hotmail.com

Hello; I am installing asterisk and dahdi on ubuntu "and I used my username bghayad to login for ubuntu and do the installation, actually I feel my problem is related to the?username and permission but I am not able how to fix it", I am facing now mainly the following two problems: The first one, asterisk is not starting automatically although I did sudo make config (for asterisk and

Hi List; How to upgrade the Asterisk, Zaptel and LibPri and keep the configuration the same? I do not need to remove current asterisk, zaptel and libpri and download new one and write new configuration. Regards, -------------- ITS IP Telephony and Contact Center Engineer Eng. Bilal Ghayad Mobile: 00965 9849460

Hi List; I have this example for Macro and I am not able to understand some line, if any one can help me plz :)- [macro-voicemail] exten => s,1,Dial(${ARG1},20) exten => s,2,Goto(s-${DIALSTATUS},1) exten => s-NOANSWER,1,Voicemail(u${MACRO_EXTEN}) exten => s-NOANSWER,2,Goto(incoming,s,1) exten => s-BUSY,1,Voicemail(b${MACRO_EXTEN}) exten => s-BUSY,2,Goto(incoming,s,1) exten

Hi List; How can I configure asterisk to receive a call from SIP end point without being registered at asterisk and its IP address is dynamic, and authentication to be based on the username and password or any other string? I know that if I place the host with static IP then no need to register, but what if the voip gateway was having dynamic IP and I do not need to register on asterisk, but I

Hi List; Did any one tried the H.323 module? How much it is stable and work fine? Regards, ------------ ITS IP Telephony and Contact Center Engineer Eng. Bilal Ghayad Mobile: 00965 9849460 ____________________________________________________________________________________Ready for the edge of your seat? Check out tonight's top picks on Yahoo! TV. http://tv.yahoo.com/

Hi List; Why I need zlib1g to do installation for Zaptel? Will zlib1g do compression or it will what extactly do during the installation process? Regards Bilal ____________________________________________________________________________________ Moody friends. Drama queens. Your life? Nope! - their life, your story. Play Sims Stories at Yahoo! Games. http://sims.yahoo.com/

Hi List; I read the following sentence: "The CLI prompt is set with the ASTERISK_PROMPT UNIX environment variable" In the following link: http://www.voip-info.org/wiki/index.php page=Asterisk+CLI+prompt The question is: what is the ASTERISK_PROMPT UNIX environment variable and where I can access it to change it? Also where I can find information about it? Regards Bilal Ghayad

Hi List; I need to use an prepaid billing system with Asterisk, and I do not know which one is more stable and integrated with Asterisk? A2Billing or AstBill or ASTCC? Also, from where I can download it and ready about its configuration? Regards ITS IP Telephony and Contact Center Engineer Eng. Bilal Ghayad Mobile: 009659849460

Hi List; Asterisk does not have any kind of cards that can work with it to be used with Digital Phones (digital phones differ than analoge phone and differ than IP Phones). Anyone can advise about this as I did not find this on Diguim Regards Bilal Ghayad __________________________________________________ Do You Yahoo!? Tired of spam? Yahoo! Mail has the best spam protection around

Hi List; If I need traffic to be directly between the endpoints, then I have to set the canreinvite = yes? If I did not configure the canrenvite at all, then by default it will pass the traffic via Asterisk and not directly between the endpoints? What if one endpoint was SIP and configured with canreinvite=yes while other endpoint was IAX2 and configured with canreinvite=yes, then they can send

Hi List; If I am configuring Diguim Analoge card, then I need to run #modprobe wctdm, but the question why I need to run #modprobe zaptel also? What #modprobe zaptel does a things that #modprobe wctdm does not do? Any help? Regards Bilal ____________________________________________________________________________________ Looking for a deal? Find great prices on flights and hotels

Hi List; I need to do a call transfer using analoge phone connected to fxs, but I do not need this to be done using flash hook, let it to be using the # or * or any code, but how I can configure that this code is for transfer? Also, I do not need the flast hook to be used for trasfer as it cause usually a confusion to distinguish between the hangup and the call transfer. Any advise? Regards

I am talking about the SIP. Now the new mobiles (Nokia, Erecson, Panasonic, iPot, ... etc) all of them support SIP capability. They are able to register to any SIP server (by giving the IP address, username and password). Fring is one of the software that can be installed on the mobile devices and can register on the SIP servers. BUT, the new mobiles currently come with built in SIP (no need to

Dear Alex; Thanks for your kindly reply. Please explain for me what do u mean exactly in "a la" in the following sentence u wrote it below? " in SIP, this can be done via "re-INVITEs" a la the canreinvite= option for SIP peers in sip.conf" Another thing, do u mean that it is easier (better) if we need H.323 endpoint to talk with SIP endpoint then we use full

Hi List; Can someone advise me which IP Phone model that has buttons that can be assigned to do specific functionalities (call pickup, call formward, call appearance) and a transfer button and hold button? Which is the best of the following (that has buttons can be assigned to specific functions): Cisco 7970 or 7960 Polycom 501 Grandsream IP Phone Budge Tone 1001 or 1002 Linksys SPA 942 or 922

Dears; To patch libpri: I just place the patch file in the libpri source directory and then I run make and make install? Or I need to compile the dahdi and asterisk also? If the problem stayed, do I have to go for previous libpri version? Or for previous dahdi version and asterisk version? Regards Bilal ----------- > bilal ghayyad wrote: > > But I am afraid it is a bug because I

Hi; Can some one advise me an PC to Phone client software to be used under Windows OS at the client side, to be communicated with Asterisk PBX? Regards Bilal

Dear; Thanks a lot for guiding me. Is it possible that the installation libpri-1.4.11.5 newer than the libpri-1.4.11.5-patch? Well, when I typed (note: I am trying to apply the libpri-1.4.11.5-patch for the libpri-1.4.11.5): libpri-1.4.11.5# patch -p0 -i libpri-1.4.11.5-patch It gave me that patched detected as shown below (example of one file, and I got same for other files): patching file

Hi List; I need to configure a softphone to be client and use it with Asterisk, which is the recommended one? Is it iax2? Regards Bilal ____________________________________________________________________________________ Boardwalk for $500? In 2007? Ha! Play Monopoly Here and Now (it's updated for today's economy) at Yahoo! Games.