similar to: Xorcom Bri 4 Port USB

I'm having problems getting an Xorcom USB Bri 4 dialling out in Australia. I can receive calls into the system without an issue, but I can not for the life of me dial out of the system. Below are my configs, I'm hoping its something simple that I just can't see as I've been looking at it for to long. Can any one point me in the right direction. P.S. Yes it is meant to be in TE

Hello, I recently got a problem I have never seen during my previous installations. I have a Xorcom device with 4 BRI and 8 FXS ports. I use ubuntu Linux and asterisk 1.4.22. Everything works fine but after some time zap channels disappear in asterisk. root at pbx1:~# cat /proc/zaptel/* Span 1: XBUS-00/XPD-00 "Xorcom XPD #00/00: BRI_TE" AMI/CCS NOTOPEN 1 XPP_BRI_TE/00/00/0 Clear

Hi all, After running fine for a few months now asterisk seems to hang frequently , still functioning but the DAHDI channels seem busy (users report a busy signal when calling or being called) A reboot will allow it to run for another day or maybe 2 or 3 till the problem occurs again. running stock Asterisk 1.6.2.9-2+squeeze2 on Debian with stock kernel 2.6.32-5-686 i get the following

, address 2 Dec 30 21:42:08 wedekindpbx1 kernel: [ 3746.344611] ERR-xpp_usb: XBUS-00: x= usb_listen: usb_submit_urb failed: -19 Dec 30 21:42:08 wedekindpbx1 kernel: [ 3746.353325] INFO-xpp: XBUS-00: [] D= isconnecting Dec 30 21:42:08 wedekindpbx1 kernel: [ 3746.353373] Zaptel: Master changed = to XBUS-00/XPD-01 Dec 30 21:42:08 wedekindpbx1 kernel: [ 3746.353382] Zaptel: Master changed = to

Hello List, it is a very long time since I wrote here.... It has been still in Zaptel times.... Today I am run into a related problem: I can't get a DAHDI setup to work 100%. I am configuring an Astribank XR00013 (BRI, two ISDN ports). At some degree the installation (latest DAHDI drivers, Asterisk 1.6.0.18 on Centos 5.x) works. I can get incoming calls to the dialplan context that is

We have recently install an asterisk solution with about 60 physical extensions. While the system is running it runs reasonably well (Still have a few teething problems) but twice now they have experienced a degradation in voice quality and dropped calls and then finally asterisk completely crashes out. Restarting asterisk will work for a little while and it will crash again, each time less time

Hello, I've one astribank with 8 FXO unit and 8 pstn lines connected to the astribank. When I receive calls on my ipphone I get always Unknown callerid. It's is possible to receive the callerid from the lines on the astribank unit? This is my config: [channels] language=es context=from-zaptel signalling=fxs_ks ;rxwink=300 usecallerid=yes callerid=asreceived ;cidsignalling=bell

Hi All Just a quick check on the best way to ensure multiple cards/devices load in the correct order. Asterisk 1.8 with Sangoma A101 had no problems until we introduced an Astribank. root at pabx377:/etc/asterisk# dahdi_hardware -v usb:001/004 xpp_usb+ e4e4:1162 Astribank-modular FPGA-firmware LABEL=[usb:X1060395] CONNECTOR=@usb-0000:00:1d.7-3 XBUS-00/XPD-00:

Hi everyone. We have a problem here... Hope somebody can give us some hints. We have a HP ProLiant DL180 G6 Server with a Debian/Lenny sytem. Asterisk 1.4.21.2 (1.4.21.2~dfsg-3+lenny1) with zaptel (1.4.11) and libpri (1.4.3) is installed. There is a QuadBRI-Card installed: # lspci -vv -s 06:04.0 06:04.0 ISDN controller: Cologne Chip Designs GmbH ISDN network Controller [HFC-4S] (rev 01)

Hi, I have a client that has a 24 channel voice T1 that I have been using e&m signalling over for a number of years. The local telco finally got an ISDN switch and wants to move them to PRI. I didn't see this as a big problem - I've done a few others on this particular Caribbean island without issues, but this would be the first time with a Xorcom unit involved. We tried to do

Sir, i am using goautodial server , bri card is showing ok but when i try to call that showing below , This configuration is in doing in dubai , so kindly help me how can connet the call from this , what is my mistake is in this :::chan-dahdi.conf [channels] #include dahdi-channels.conf language=en context=default usecallerid=yes hidecallerid=yes callwaiting=yes usecallingpres=yes

Hi Guys, An 8 channel Astribank is connected to Trixbox 2.8 and I ran freepbx-module-zapauto but I get the following when running these commands and can't make calls out: [Trixbox]# dahdi_genconf xpporder /usr/sbin/dahdi_genconf: warning - OLD DRIVER: missing '/sys/bus/xpds/devices/00:0:0/timing_priority'. Fall back to /proc pbx*CLI> dahdi show channels Chan Extension Context

Hi All, I've a BT Versatility PBX that I want to connect to my asterisk 11.9.0 box via BRI port in NT mode but actually I wasn't able to get it working. I've another standalone PBX, it's a Panasonic model, which works fine connected to the same port. The BT connected to a UK BT BRI line works quite fine after roughly a minute once connected. The PBX can be seen at

I'm having trouble getting a xorcom set up. A large part of the problem is that the box is a _long_ way away and I can't get to/at it easily, so while I could probably fix this in a few hours if the machine were in front of me, I'm struggling over a slow unreliable laggy link. Ok, enough whining from me. I have a new Xorcom plugged into the usb of a Suse 11 machine I built Dahdi

H all... I have an Astribank (8FXS/16FXO), IBM X3200 M2, Asterisk-1.6.2.1, dahdi-linux-complete-2.2.1, libpri-1.4.10.2, centos-5.4 final. My problem is, every time i unplug the astribank power supply, and reconnect it, astribank cannot work again (lsusb result is 11x0)... but, after reinstall the asterisk and dahdi, astribank will detected (lsusb result is 11x2)... any suggestion? Regard,

I have a pretty large setup on one of my customers. Digium TE420B (with echo cancelling module), 3 Xorcom Astribanks with 32 FXS each and 1 Xorcom Astribank with 16 FXO. These FXO ports are NOT used for fax/data transmission, as they are connected to cell phones. Not really related to the issue, but there are also 250 SIP phones. The problem is that fax and dial-up connections are really

I am getting the following compile error on centos 5. Any suggestions? Jerry CC [M] /usr/src/digium/zaptel-1.4.1/xpp/xbus-core.o /usr/src/digium/zaptel-1.4.1/xpp/xbus-core.c: In function ?debugfs_open?: /usr/src/digium/zaptel-1.4.1/xpp/xbus-core.c:171: error: ?struct inode? has no member named ?u? /usr/src/digium/zaptel-1.4.1/xpp/xbus-core.c: In function ?proc_xbus_command_write?:

Hello- After configuring DAHDI and starting asterisk, I get the following message continuously on the Asterisk console: WARNING[2057]: chan_dahdi.c:4158 pri_find_dchan: No D-channels available! Using Primary channel 16 as D-channel anyway! My card is a D410P configured for E1, only the first span is configured, and configuration snippets are as follows: From /etc/dahdi/system.conf:

I get the following error when trying to compile zaptel on CentOS 5 kernel 2.6.18-8.1.3.el5 CC [M] /root/asterisk-src/zaptel-1.2.17.1/xpp/xbus-core.o /root/asterisk-src/zaptel-1.2.17.1/xpp/xbus-core.c: In function ? /root/asterisk-src/zaptel-1.2.17.1/xpp/xbus-core.c:171: error: ? has no member named ? make[3]: *** [/root/asterisk-src/zaptel-1.2.17.1/xpp/xbus-core.o] Error 1 make[2]: ***

hello list, i have installed 2 diguim cards in my server using asterisk 1.4 (i use the old version with zapata.conf and zaptel.conf) i want to use the span 1 for group 1 and span 2-span 6 for the group 2 (i want to active the round-robin for span 2 and 6) in order to activate the WIMAX and FH please see the configuration below and tell me if there is anything wrong question 2: what is