similar to: chan_iax2.so issues

Hello everybody, This is a problem disturb me for long. I run asterisk Asterisk 1.4.14 and A2Billing 1.3 in the same Debian 4.0 ETCH server. And there is also FoneBridge for TDM over Ethernet with E1 to make as well as receive calls from mobiles or PSTN. And IAX2 trunk runs between Asterisk and A2Billing. For most of the time they really do a good job. But some hours or days later----I mean it

I just updated to the new CVS and now I am getting the following error from chan_zap (modprobe wcfxo works fine): WARNING[16384]: File chan_zap.c, Line 577 (zt_open): Unable to specify channel 1: Device or resource busy ERROR[16384]: File chan_zap.c, Line 4781 (mkintf): Unable to open channel 1: Device or resource busy here = 0, tmp->channel = 0, channel = 1 ERROR[16384]: File

Can someone explain me this message: "chan_iax2.c: Ooh, voice format changed to ..." Where can I find a list of numeric codes used to identify voice format? Then, sometime I get an infinite loop of messages like these: DEBUG[15015] chan_iax2.c: Ooh, voice format changed to 1 WARNING[15015] channel.c: Unable to find a codec translation path from g723 to alaw DEBUG[15015]

I have two units at customer locations in the Caribbean registering to a server in the US. Both units are connected to the Cable TV company's internet feed. If I run mtr to the units I see clean internet and low latency, but when I watch the CLI, I see constant problems. The audio quality is terrible, but I can't see why. Sep 3 16:42:46 NOTICE[20423]: chan_iax2.c:7014 socket_read:

Hi, I was messing around with FireFly last night and got asterisk to crash hard. It looks like the bug is a division by zero in chan_iax2.c. I reproduced it and here are some infos I got from gdb: [Switching to Thread 245775 (LWP 23251)] 0x41154918 in calc_timestamp (p=0x816b710, ts=0, f=0x424eef24) at chan_iax2.c:2896 2896 int diff = ms % (f->samples / 8);

Hi All We have a private network setup (no nat) with three types of phones connecting to asterisk via SIP. We have Polycom, Grandstream and Cisco 7940 IP phones. When we ring polycom to grandstream or grandstream to polycom then both phones can send and receive voice fine and all is well. When we dial any combination of Cisco and either Polycom, or Granstream the Cisco, no voice is being sent

Hi, I have a wildcard x100p. I just installed asterisk by following step: # cd ../zaptel # make clean ; make install # cd ../libpri # make clean ; make install # cd ../asterisk # make clean ; make install # make samples When I test Asterisk typing # asterisk –vvvvc I find one error and one warning: [chan_iax.so] => (Inter Asterisk eXchange) == Manager registered action IAX1peers ==

Hi everyone, IAX2 softphone is not working with the “Unregistered” part in the asterisk (chan_iax2.c and data_pgsql.c) But with the Xlite softphone the unregistered worked properly and ast_data properly updated the IP address and port number in the database. I have seen some codes in the chan_iax2.c file: “ast_verbose(VERBOSE_PREFIX_3 "Unregistered '%s' (%s)\n", p->name,

Hi All, I'm having a problem after reinstalling the operating system. Festival works fine for SIP, but when IAX users are calling the same extension they don't hear the festival and I see the next message on console: NOTICE[3996]: chan_iax2.c:2995 iax2_read: I should never be called! I googled and couldn't find a solution, if somebody can help.... neobase*CLI>

Hi, all Please help me. My platform is RedHat Linux 9.0. I have a wildcard x100p. I just installed asterisk by following step: # cd ../zaptel # make clean ; make install # cd ../libpri # make clean ; make install # cd ../asterisk # make clean ; make install # make samples When I test Asterisk typing # asterisk –vvvvc I get one error and one warning: [chan_iax.so] => (Inter Asterisk

Just a quick question ---cut--- [Sep 17 15:52:14] WARNING[8232] app_dial.c: Unable to create channel of type 'IAX2' (cause 34 - Circuit/channel congestion) [Sep 17 15:52:14] WARNING[8232] chan_iax2.c: No more space [Sep 17 15:52:14] WARNING[8232] chan_iax2.c: Unable to create call [Sep 17 15:52:14] WARNING[8232] app_dial.c: Unable to create channel of type 'IAX2' (cause 34 -

Hello, I have searched the lists, and have seen this message posted numerous times, however there never seem to be any replies to it. I was curious if anyone had figured out the WARNING: File chan_iax2.c, Line 5466 (set_config): Ignoring port for now Everything seems to work just fine, however when I try to change iax.conf port to 4569 it doesn't seem to like that either. Thanks, Brent

On 1/2/2024 4:03 PM, thelma at sys-concept.com wrote: > I'm using asterisk-16.30.1 > > When I try to call another asterisk server over IAX I get a busy signal, > > chan_iax2.c:4739 __auto_congest: Auto-congesting call due to slow > response >     -- IAX2/192.168.143.1:4569-656 is circuit-busy > > Asterisk-16.16 is working normally, no congestion error. There is not

I'm using asterisk-16.30.1 When I try to call another asterisk server over IAX I get a busy signal, chan_iax2.c:4739 __auto_congest: Auto-congesting call due to slow response -- IAX2/192.168.143.1:4569-656 is circuit-busy Asterisk-16.16 is working normally, no congestion error. -- Thelma

I had two asterisk servers connected with each other, both were 1.4.22 but I've upgraded one to 1.4.37 and now I get a message when I try call from asterisk-1.4.22 to asterisk-1.4.37 ERROR[4539]: chan_iax2.c:4330 handle_call_token: Call rejected, CallToken Support required. If unexpected, resolve by placing address 192.168.140.1 in the calltokenoptional list or setting user guest

Hi, I am getting the following messages for a few days. WARNING[10148]: chan_iax2.c:1219 __send_lagrq: I was supposed to send a LAGRQ with callno 15691, but no such call exists (and I cannot remove lagid, either). I got 2 iax trunks which used by test purposes only. And no iax clients or no calling rules thru this iax channnels so far.. So why do i keep getting that messages.

Dear all, I just update my asterisk from v 1.0 to lasted CVS, I also used module res_config_mysql in asterisk-addons. Every working fine, but i got problem with IAX user can't make a call, when IAX user make a call, i got message in console like this Feb 21 06:20:07 NOTICE[365]: chan_iax2.c:6090 socket_read: Rejected connect attempt from xxx.xxx.xxx.xxx, who was trying to reach '411@'

Hi, Recently, one of my Asterisk servers stopped connecting calls and required a reboot to "fix it" (did not try to restart or reload). The log showed loads of this message: NOTICE[302] chan_iax2.c: I should never be called! This highly repeated message seems to be preceded by something like: WARNING[10767] channel.c: Exceptionally long voice queue length queuing to

> On Jan 2, 2024, at 23:17, thelma at sys-concept.com wrote: > > On 1/2/24 15:13, asterisk at phreaknet.org wrote: >>> On 1/2/2024 4:03 PM, thelma at sys-concept.com wrote: >>> I'm using asterisk-16.30.1 >>> >>> When I try to call another asterisk server over IAX I get a busy signal, >>> >>> chan_iax2.c:4739 __auto_congest:

> Asterisk Project Security Advisory - ASA-2007-013 > > +----------------------------------------------------------------------------------+ > | Product | Asterisk | > |----------------------+-----------------------------------------------------------| > | Summary | IAX2