similar to: DUNDi configuration problem

I have three Asterisk boxes. Each has the following in dundi.conf: 180net => dundi_local,0,IAX,dundi:${SECRET}@${IPADDR}/${NUMBER},nopartial 180q => dundi_q_pbx1,1,IAX,dundi:${SECRET}@${IPADDR}/${NUMBER},nopartial 180q => dundi_q_pbx2,2,IAX,dundi:${SECRET}@${IPADDR}/${NUMBER},nopartial 180q => dundi_q_pbx3,3,IAX,dundi:${SECRET}@${IPADDR}/${NUMBER},nopartial My iax.conf on all three

Hi few weeks ago I read about redundancy (HA) of asterisk boxes using DNS, DUNDi, so I decided to give it a try. OS FreeBSD 6.1-RELEASE, asterisk 1.2.7.1 on one peer I get: lk110*CLI> dundi show peers EID Host Model AvgTime Status 00:11:43:3d:69:e6 195.28.109.37 (S) Symmetric Unavail OK (1 ms) 1 dundi peers [1 online, 0 offline, 0

> -----Original Message----- > From: Watkins, Bradley [mailto:Bradley.Watkins@compuware.com] > Sent: Thursday, June 15, 2006 10:36 AM > To: Asterisk Users Mailing List - Non-Commercial Discussion > Subject: RE: [Asterisk-Users] DUNDi Not Able to > HandleComplexFailoverSituations > > > Is it possible for you to explain in more detail the > situation involved.

It seems that I am having a heck of a time explaining my attempts at distributing ACD Queues to the list. Here's one little problem, that's only a piece of the puzzle. dundi.conf: 180q => global_dundi_q_pbx1,100,IAX,dundi1:${SECRET}@${IPADDR}/${NUMBER},nopartial 180q => global_dundi_q_pbx2,200,IAX,dundi2:${SECRET}@${IPADDR}/${NUMBER},nopartial 180q =>

Hi All, I've been banging my head on a small dundi problem... I have two * servers setup, both have almost identical dundi.conf files: root@tsjonge:/opt/asterisk/etc# cat dundi.conf [general] department=thuis organization=pipsworld locality=Amsterdam stateprov=NH country=NL email=remco@pipsworld.nl phone=+31207508308 ;bindaddr=0.0.0.0 ;port=4520 entity=00:02:b3:49:69:5e ttl=16

Hi, I'm having difficulties with using DUNDi between two servers. If it were three I think I could control looping by limiting TTL, but with two I'm not sure how to prevent a loop causing bad things to happen. I've tried ttl=1 but things still blow up. The DUNDi configurations are pretty simple and work just fine in both directions as long as only one of them is using the switch

>From the reading and testing I have done it doesn't look like SIP supports a username and password in the Dial string. I currently have the following mapping. priv => dundi-extens,0,SIP, dundi:pass at 1.1.1.1/${NUMBER},nounsolicited,nocomunsolicit,nopartial On the sending side I see NOTICE[31598] chan_sip.c: Conflicting extension values given. Using 'dundi' and not

Hi, i'm having asterisk with sip working fine, including dundi lookups. The only problem i'm having is that the dundi answer allways contains my internal, private ip. Is there any way to set the targeting ip that is sent out in the dundi answer (to my public ip or any other where i want to receive the call)? Regards, Andreas.

Hi all, I'm new in asterisk and I got to set up a dundi config for my work. I have 2 PBX for the test, the two PBX are in the same local network PBX A : 192.168.199.23 PBX B : 192.168.199.21 my config files : (on PBX B , the config files on PBX A looks like it) /etc/asterisk/dundi.conf [general] bind=192.168.199.21 port=4520 cachetime=5 ttl=32 autokill=yes entityid=00:30:18:4C:33:53

> Questions: > > 1. Is the wiki DUNDi example and the dundi.conf file too difficult to > follow for new users? > I wouldn't exactly say that it is too difficult but that the target audience for the default examples is not the average person/entity that could make use of the power inherent with DUNDi. When an average * user/admin wants to use DUNDi they will want to start out

Greetings list, I've been using DUNDi for some time now to prevent calls between users going out via PSTN if there's no need, set up as follows: [macro-dundi-e164] exten => s,1,Goto(${ARG1},1) include => dundi-e164 [dundi-e164] include => in-e164 switch => DUNDi/e164 My outbound call macro tries [macro-dundi-e164] first, if that fails then goes onto PSTN connectivity.

Questions: 1. Is the wiki DUNDi example and the dundi.conf file too difficult to follow for new users? 2. Does the complexity of the DUNDi setup discourage you from using it or even attempting to configure it? 3. If there was a simple tutorial, step by step guide with easy to setup and test examples, would this encourage more users to investigate and use DUNDi? I'm interested in putting

Hi everyone! I'm quite a newbie at this Asterisk stuff so please bear with me. We've recently decided to start training in Asterisk via AsteriskNow! Asterisk version is 1.4.18.1 through AsteriskNow! 1.02 The box we have is paired with a Digium TE110P and we've managed to get it to the point where incoming calls via a single DID (from NTT Japan) can be received and answered

Dear Users ! I have recently installed asterisk 1.4 i got a warning message whenever i use reload or extensions reload. [Jun 29 19:22:11] WARNING[4539]: pbx.c:6236 ast_context_verify_includes: Context 'ael-local' tries includes nonexistent context 'ael-parkedcalls' [Jun 29 19:22:11] WARNING[4539]: pbx.c:6236 ast_context_verify_includes: Context 'ael-dundi-e164-local'

Hi list, i've problems with my * server and the 4 phones which are linked to it. i've 2 grandstream bt100 with the firmware upgraded to 101, a wi-fi phone (i don't know its brand) and another ip phone i don't know its brand. with this sip.conf : [general] port = 5060 bindaddr = 192.168.100.229 context = default ;x changed from default to sip localnet = 192.168.100.0/24

My phone still says Not-Registered. I have a Polycom SoundPoint 600 SIP phone. Here is my sip.conf file: ; ; SIP Configuration ; [general] context=default ; Default context for incoming calls port=5060 ;added bindport=5060 ; UDP Port to bind to (SIP standard port is 5060) bindaddr=0.0.0.0 ; IP address to bind to (0.0.0.0 binds to all) srvlookup=yes ;

Dear community, Please help. I've been looking around the internet (and in this great forum) for help with DUNDi setup between servers (I'm using Elastix) and while I can get my servers to lookup extensions on each other very well, I have not been able to successfully make calls between servers. For my test environment, I have 3 servers setup for now, and these are the steps I've

Anyone out there have a functional DUNDi configuration using SIP for the inter-Asterisk transport? I've gotten it to work with IAX2, but if I change it to SIP it does not pass the call over even though it knows where to send it. Thanks. The contents of this email message and any attachments are confidential and are intended solely for addressee. The information may also be legally

Good afternoon gentlemen (and ladies). A costumer of mine has many servers and each one maps their SIP extensions to the others via DUNDi. It works like a charm. SIP extensions can only register at one server, the one they "belong" to. In case one extension wants to call other that is registered in another server, DUNDi takes care of that by calling the other server using IAX2 and G.729

Hello, i'm using asterisk 1.4.9 in fedora 7, i was compiled its with this package: libpri-1.4.2 asterisk-1.4.9 spandsp-0.0.4 unicall-0.0.5pre1 libmfcr2-0.0.3 libsupertone-0.0.2 libunicall-0.0.3 zaptel-1.4.4 i'm using a E1 pci card with R2 but they not work, when I start the asterisk its generate this log: [May 12 08:53:24] WARNING[30814] channel.c: No channel type