similar to: ZAPTEL PROBLEM

Hi all, I've just realized that my asterisk isn't storing cdr inputs in mysql. cdr_mysql.conf is well configured and I don't know what else should i configure. I'm using Xorcom's packages, "cdr status" shows: voip*CLI> cdr status CDR logging: enabled CDR mode: simple CDR registered backend: csv CDR registered backend: cdr_manager CDR registered backend:

Hi folks, I was wondering if there's a guide on how to configure sugarCRM Integration with Asterisk. I was looking in google and all i found was about Trixbox, which has sugarcrm integrated by default. Regards, -- Diego Quintana a.k.a. RouterMaN Ingeniero de las Telecomunicaciones Linux Registered User #382615 - http://counter.li.org/ SIP # 1-747-633-6676 Ext. 1011 FWD # 764839 Ext. 1011

Hi all, I've just installed again my Asterisk using Xorcom repositories. I can make extensions, but when using any extension i want to dial anything, I got "404 not found" using Xlite. Any ideas of what can be happening? Regards, -- Diego Quintana a.k.a. RouterMaN Ingeniero de las Telecomunicaciones Linux Registered User #382615 - http://counter.li.org/ SIP # 1-747-633-6676 Ext.

Hi everybody, I've installed "future" packages (asterisk 1.2 and freepbx) from Xorcom's Repository in a debian etch, but when i want to uninstall freepbx-panel, i got this error: dialer:~# apt-get remove --purge freepbx-panel Leyendo lista de paquetes... Hecho Creando ??rbol de dependencias... Hecho Los siguientes paquetes se ELIMINAR?N: freepbx-panel* 0 actualizados, 0 se

Hi All, I hope I'm posting this to the appriopriate list, and that cross posting to two lists is OK. (If not, I'm sure I'll hear about it quickly :)) I'm running Asterisk on my (new) VIA EPIA-V motherboard. This seems to be the ideal platform for a home version of asterisk - its small, quiet, low power, and should have plenty of computing horsepower if only it would work!

Hi all, I want to make a SIP trunk between a Cisco 2811 router and a Asterisk. Both 2811 and Asterisk are working fine (2811 has 1XX and asterisk 2XX). Now I want to configure a trunk so that 2811 users can call * users. I've been reading a lot but I'm still confused. Hope you can help me, -- Diego Quintana a.k.a. RouterMaN Ingeniero de las Telecomunicaciones Linux Registered User

Hi folks, I was wondering what happened to Areski CDR viewer that came before with Freepbx. I've noticed that the live-CD contains Areski but the repositories don't have it. Will you fix that? or shall I install Areski from sources? Regards, -- Diego Quintana a.k.a. RouterMaN Ingeniero de las Telecomunicaciones Linux Registered User #382615 - http://counter.li.org/ SIP # 1-747-633-6676

Hi all, I was wondering if there is any IAX2 sniffer and decoder. Wireshark can decode and play RTP streams using G.711, and Cain & Abel decodes and plays any kind of RTP stream. But I didn't find anyone that can decode IAX2 streams. Any programs?? Regards, -- Diego Quintana a.k.a. RouterMaN Ingeniero de las Telecomunicaciones Linux Registered User #382615 - http://counter.li.org/ SIP #

Hi all, I have installed centos 5.1 x86_64. 2.6.18-53.1.14.el5 Everything seems to be working fine except that the rtc module is not working. cat /proc/interrupts shows: CPU0 CPU1 0: 129 0 XT-PIC-XT timer 1: 330797 0 XT-PIC-XT i8042 2: 0 0 XT-PIC-XT cascade 3: 4 0

Hi I have come across a problem, with my tdp410 and soekris board (basically pc on a chip amd geode cpu). I am using the box as a firewall/asterisk box. The problem occurs when I drop ppp and I get dead loop dectiotn going, I seem to lose interrupts and get lots of messages in syslog from wctdm24xx saying missed interrupt increasing latency its out lined here

Here are another three problems with logarithmic scales: 1) segments() does not work with logarithmic scales. I suggest to change lines 962-973 in "plot.c": for (i = 0; i < n; i++) { if (FINITE(xt(x0[i%nx0])) && FINITE(yt(y0[i%ny0])) && FINITE(xt(x1[i%nx1])) && FINITE(yt(y1[i%ny1]))) { GP->col = INTEGER(col)[i % ncol];

Hello I am using a Junghanns QuadBRI ISDN card - the module name is qozap. If I like at my interrupt assignment, qozap is sharing interrupt 10 with libata and uhci_hcd. I think libata is the IDE hard drive module and uhci_hcd is a USB module. linux:~ # modprobe qozap linux:~ # cat /proc/interrupts CPU0 0: 12634579 XT-PIC timer 1: 10 XT-PIC i8042

hi list. after my unsuccessfull experiences with mISDN i tried again to implement a zaphfc based solution. problem is: sound on calls via capi is stuttering/broken and therefore unuseable. my conf: - cel 1300, 256mb ram - avm b1 via capi connected to my outgoing ISDN - acer surf pci via zaphafc and crosslink cable with termination as internal bus - siemens gigaset 3035 as internal phone -

> Subject: Re: [Asterisk-Users] Booting error - Unable to specify channel 2: > No such device I just went through all this as well. The best thing to do IMHO is to try to find a way to manually assign IRQ in the BIOS. Also, and this is what I didn't see at first, some slots SHARE IRQ. Avoid this! If you are not using USB at all, turn it off in BIOS if possible. Tell the BIOS

I have some new PC hardware I'm using with the Intel H67 chipset. I created a bzImage I use for a PXE environment for a recovery mode, installing OS images, etc. The new mobo doesn't have a VGA port but instead DVI. Everytime I unplug the DVI cable it seems to cause "Disabling IRQ #11". After that the PC is basically unusable. The /proc/interrupts shows that hdd, usb, nic,

Hi All, I have an equipment loaded with 4 X100P (numbered 1-4)) and one T400P (numbered 5-8). Everything works fine except that I cannot use one of the FXS ports (number 5). If I configure zapata.conf to recognize it, the whole system voice quality suffers. I've tried already to switch PCI slots, with no results. Below is a snapshot of my /proc/interrupts, maybe this can shed some light on

Excuse my ignorance here, but I am desperately trying to isolate the IRQ for my TE110P card (shown below as t1xxp) Ive gone into my bios and disabled all usb , parallel, serial and some other devices, those that I needed to keep, I have moved off of IRQ 10 and onto IRQ 5, but everytime I boot up, I get usb-uhci and ehci_hcd using IRQ 10 as well as my Digium card. Does anybody know what these are

Thanks for the reply Bill. I am aware of the interrupts problem. To solve it I have already disabled my serial ports freeing up interrupts 3 and 4 and these are allocated to the two cards. This was done 2 months ago and has not solved the problem. Is there any way that something can wake up every now and then and generate these two interrupts? My current /proc/interrupts is as follows:

Dear List, I have a logical data frame with NA's and a grouping factor, and I want to calculate the % TRUE per column and group. With an indexed database, result are mainly limited by printout time, but my R-solution below let's me wait (there are about 10* cases in the real data set). Any suggestions to speed this up? Yes, I could wait for the result in real life, but just curious if I

Dear R users, suppose we have a random walk such as: v_t+1 = v_t + e_t+1 where e_t is a normal IID noise pocess with mean = m and standard deviation = sd and v_t is the fundamental value of a stock. Now suppose I want a trading strategy to be: x_t+1 = c(v_t – p_t) where c is a costant. I know, from the paper where this equations come from (Farmer and Joshi, The price dynamics of common