similar to: G.729 & Voicemail

Hi Sir, We have integrated Skype with Asterisk (skype user id:- rexesbposolutions). Each call which is coming to skype account is getting transfered to Asterisk Queue. It has following two cases: case 1: When we call from normal skype account to skype account (rexesbposolutions), everything is working fine. case 2: This skype account (rexesbposolutions) has been assigned with a online virtual

Hi list! My problem: I have three extensions in my Asterisk 1.8.30.0 and they have a voicemail. On two of these numbers the voicemail works without any problem, on the other it doesn't... I get this error: [Oct 17 17:01:29] WARNING[14700]: channel.c:5254 set_format: Unable to find a codec translation path from 0x100 (g729) to 0x2 (gsm) [Oct 17 17:01:29] WARNING[14700]: file.c:957

I am trying to create a %100 g729 (with no transcoding) system (using a Soekris, of course). I am running AstLinux with the native sounds, g729 is the only codec allowed, %100 SIP (g729 only allow=) - I think I am covering all of my bases. I have only "format=g729" in voicemail.conf. On an incoming call to a mailbox, everything goes well until recording the message. When the

Hello. I have a codec problem to send calls from a SIP device to a H323 gateway. First I'll explain the scenario: - Asterisk 1.2.1 - The SIP phone can use any codec I want. - The H323 gateway can only use g729 (cause it's not under my administration) - SIP phone has g729 configured, so my asterisk doesn't need to "transcode" (I don't have licences for g729) - sip.conf

Hi i am trying to do the same thing: receive a call from a cisco callmanager and forward it to a SIP user. Asterisk is compiled with h323 support, and is configured as a gateway in the cisco callmanager. h323.conf: [general] port = 1720 bindaddr = 193.x.x.x ; this SHALL contain a single, valid IP address for this machine allow=all extension.conf: exten = 3298,1,Answer exten =

Hi, I have just signed up with Voxee.com and have attached my Asterisk server to dial them via IAX2. Below is the start of the log which dials the number and promply hangs up when the call is answered, with the logs saying that the channel is not compatiable. I have traced this down to the g.729 codec which I don't have installed. Any ideas on how to force that the codec not be used?

Hello, I have just updated my Asterisk installation from 1.2x to 1.4 (on FreeBSD) - mostly everything seem to work fine. However, I use G.729 pass-thru - and I have before successfully used the following setup: http://www.voip-info.org/wiki/index.php?page=Asterisk%20G.729%20pass-thru However, it is not working with 1.4 - I see the following errors: [Apr 16 15:59:24] WARNING[10139]:

Dear all I have Asterisk which is connected with avaya through E1 back 2 back now i have on asterisk side G.711 codec and Avaya also useing G.711 codec everything fine. I need G.729 on my asterisk side. can i have lots of SIP phone on my lan and issue is i have 2 to 3 building so problem is LAN is congested thats why i need G.729 Now testing perpose i have download

I'm sitting here with my dunce cap on. My weak excuse is that I haven't ever played with g729 before. I have a Sipura 841. I have the phone config set to use g729. Its appropriate sip.conf entry, and the IAX stanza for my ITSP all set to disallow=all, allow=g729. But as soon as I dial, I get a complaint from the server: -- Call accepted by 66.225.202.72 (format g729) --

Hi i'm trying to connect to the PSTN in the following way sip ATA -> * -> gnugk -> Cisco AS5300 -> PSTN I'm using asterisk CVS-HEAD-06/01/05-14:33:15 running over RH EL3 Asterisk-Oh323 0.7.2 pre1 Open H323 v1.13.5 pwlib v1.6.6 and I'm having a lot of trouble, gnugk and * both have public ips and are not behind any type of firewall, the sip ATA is behind a firewall and

While we're on the subject of G.729... I can end to end use it with no transcoding, but voicemail is the main sticking point for me - I'd need to transcode. So why can't voicemail store the audio in the format it's being streamed in on? Is there a technical reason for no voicemail storage in G.729? We have prompts in G.729, so why not the messages? It doesn't have to mix

Hi All, I have this codec problem, I use "gsm" in my iax.conf file and in teliax settings also, but the error is still appearing as below. please help me. Kumara Starting simple switch on 'Zap/1-1' -- Executing Dial("Zap/1-1","IAX2/kumara@teliax/01194777070239|30|tr") in new stack -- Called kumara@teliax/01194777070239 -- Call accepted by

Hi, I set a preference order of the codecs to my sip.conf [general] port = 5060 ; Port to bind to bindaddr = 0.0.0.0 ; Address to bind to context = default ; Default for incoming calls of not registered phones disallow = all allow = g729 allow = g723 allow = alaw allow = ulaw Connected a 'Sipura SPA' sip phone to asterisk with g729 as its preferred codec. Problem: asterisk cannot make

Greetings! to all Now, with some hard time and help from many genurous people's in the list, I have come to this point with my TDM20B card & my teliax's IAX2 account. I hope someone may help me with this issue mentioned below. I have already selected my codec as gms in my iax.conf as well as in teliax's "my account page" but still i have the same error when I attempt

I have this in sip.conf: [general] context=default allowoverlap=no bindport=5060 bindaddr=0.0.0.0 srvlookup=yes progressinband=yes [19256002182] type=friend username=19256002182 callerid="Test hone 1" <+19256002182> host=dynamic canreinvite=no secret=password context=test disallow=all allow=g729 [level3] type=peer host=xxx.yyy.16.99 context=default

set_format: Unable to find a codec translation path from ulaw to g729 Both endpoints are PAP2 set to G711 only I have 1.2.17 on Suse 10.1

how to make g.729 preferred, but failover to gsm I've purchased a few g.729 licences, and would like to set up iax.conf such that g.729 is used if they are available, but then it fails over to gsm. I'm not sure how to specify such a preference. I'll let the server transcode from ulaw (from the sip phones) to g.729. Got plenty of CPU for the number of phones we run off that

Hi list! I have 4 numbers on my Asterisk 1.8. 3 work perfectly, the 4.th not. I'm not sure, when it finish to work, since a month ago it runs without any problem... Well, if I will be called on this number I can't hear anything and in Asterisk I see these: [Jul 15 18:59:55] WARNING[8752]: channel.c:5060 ast_write: Codec mismatch on channel SIP/00493514977290-000001d1 setting write format

Hi, anyone can confirm if the Linksys's ATA and Router (PAP2-NA and RT31P2-NA) have the same limitation of just one G.729 call like the Cisco ATA 186 ? I'm testing both appliances here and found this issue but could not confirm this anywhere (nothing on the manual, no document or post from any user about this). In my tests they use G.729 only on the first call and G.711 on the