similar to: T100P -->>> TE120P

Hi list, I have a terrible noise issue with Dell SC1430 + Digium TE110P. The digium card is not sharing interrupts with any other device, as I saw in Dell's BIOS and also with "lspci -vb" command. After changing coax wire, UTP, balum, digium card ... I have found that the problem is in Dell box, so now I'm running the same Asterisk config in other server with the same

I have a brand new TE120P card that I have installed and asterisk is not starting as I am getting the error: ERROR[5054] chan_zap.c: Unknown signalling method 'pri_cpe' It seems it does not matter what I change the vaule for signalling= to, it always returns it as invalid. I have tried the config from my other 2 servers running TE110P cards and the config from AusTechPartniships

Has anyone had any compatibility issues with a TE110P card installed on a Dell Poweredge 1950? I noted the following error on the LCD display of the Dell Poweredge 1950: E1711 PCI PErr Slot 1 E171F PCIE Fatal Error B0 D4 F0. The Dell hardware owners manual states that it means the system BIOS has reported a PCI parity error on a component that resides in PCI configuration space at bus 0,

Hi, I have to link an Asterisk Box with a PBX Matra 6501. System look like this : E1------Te110P Asterisk Te110P-----E1----Matra 6501-----Phones | | Ip Phones Incoming call from E1 will enter on asterisk, if incoming number is _800n then go to IP phones. In this case no problem. But if it's an another call i want to return call to my

The Telco in Canada is been real painful. I was wondering if anyone has installed a Digium TE1X0P card in Canada and if their Telco was so difficult. The Telco will not provide us a service until they see a FCC or DOC number for the equipment ware are connecting to their service. If have found "FCC Part 68, ANSI/ITA-968-A, Including Amendment A1 and A2 Industry Canada CS-03"

Hi all I use asterisk (1.2 brach) from debian official packages and it works fine. Now I need to install and configure a Digium TE120P card, but I cannot find any guide to install it using debian packages. I would like to know if anyone of you knows about packages that would include the necessary kernel modules or any other method that won't be broken when the asterisk packages are updated.

Hi, I'm trying to connect to Telewest/Virgin Media with a TE110P using asterisk 1.4.13/zaptel 1.4.6. No matter what I try, my span always appears as PRI span 1/0: Provisioned, Down, Active My zapata.conf is currently ----------------------------------- [channels] echocancel=yes echocancelwhenbridged=no echotraining=yes switchtype=euroisdn contect=from-pri signalling=pri_cpe group=1 channel

Hi- Perhaps someone with an E100P in hand can answer this: I just received an E100P from Digium (I normally buy quad boards) I noticed that the circuit board says "T100P" on it, and I assume that the T100P and E100P both use the same circuit board. Can someone please confirm that their E100P says "T100P" on the artwork? Thanks Scott Scott M. Stingel Emerging Voice

Hi, I have successfully configured DIGIUM card and successfully communicated through it to the another E1 card running application. Can anybody tell me does TE120P support MFC/R2 protocol. Thanks and Regards sanchal singh

Hi, I have been using asterisk for a couple of months now and for thee most part, I love it. However, I'm having a problem with the drivers of the Digium TE110P. I have tried both the Debian package and the CVS. I have tried several kernels, and am now at 2.6.11. This has been working before (with 2.6.8.1), but after a reboot it stopped working and I am not able to consistently make

Hi, I try to connect my asterisk box with a classic pbx (Siemens). I have a T100P E1 card. modprobe zaptel and wct1xxp ok ztcfg -vv ok I can run asterisk and show the channels but the led still flash red My zaptel.conf : span=1,1,0,ccs,hdb3,crc4 bchan=1-15 bchan=17-31 dchan=16 My zapata.conf : ;; E1 switchtype = euroisdn signalling = pri_net group = 1 context=e1 channel => 1-15,17-31

Hi I posted earlier about having issues connecting to Telewest's ISDN, only to find out later Telewest had forgotten to turn it on - hopefully I'm not having a similar silly problem. My PRI span is now up and operational, but when I try to send a call out over it, I just get congestion tones. Occasionally, I get about one second of ring tones, only for it to cut out and play congestion.

OK I have been battling with echo problems with asterisk on ISDN for a few weeks now, and still can't solve it (although I think I have tried everything I can find.) I will try a post everything I think is possibly relevant that I can remember with the hope someone can point me in the right direction. current spec I am using (Trixbox 1.0 was still in beta at the time an didn't detect

Dear All, I'm integrating avaya commuication manager difinity ver 1.0 with asterisk using B2B E1. following are the details of my H/W, zaptel configs and software installed. Digium TE110p asterisk 1.2.19 cent OS 4.4 zaptel 1.2.18 libpri 1.2.4 etc/zaptel.conf span=1,0,0,cas,hdb3 bchan=1-15,17-31 dchan=16 when i ztcfg -vvv im having this error message and the E1 is not getting up. "cas

Hi, I have successfully configured DIGIUM card and successfully communicated through it to the another E1 card running application. Can anybody tell me does TE120P support MFC/R2 protocol. Thanks and Regards sanchal singh

Hi All, I'm having problems trying to get a TE120P operational in Canada. I keep getting a congestion error when I try to make a call. I'm not sure if my switching, parity, etc is correct. I'm hoping that someone will be able to verify my config. The Telco is SaskTel, with a 10 channel 50 DDI service. Zap show channels show and ztcfg -vv looks ok and the zttool show

what happens when you drop your gains? use /etc/asterisk/zaptel.conf and fiddle with tx and rx values. Works, most of the time. -----Original Message----- From: John McEntee [mailto:john@mcentee87.freeserve.co.uk] Sent: Wednesday, October 11, 2006 12:25 PM To: Asterisk Users Mailing List - Non-Commercial Discussion Subject: [asterisk-users] Echo problems on ISDN. (mainly incoming calls) OK I

Hello Folks, I'm trying to decide here between a few cards for connecting an Asterisk box to a single E1 channel (either PRI or R2 signaling): - Digium E100P: has been replaced by the TE110P below, but can still be had at places like digitnetworks.com for $475, and I guess there's always a place for good-olde-obsolete cards in the world as long as they work :-) - Digium TE110P:

Hello, Does anybody know of a place to get a half-height PCI slot bracket for the Digium T100P card? I have an application to fit them in 1U cases for small, deployable PBX's. The T100P itself is short enough to fit in a half-height slot but I need an appropriate mounting bracket to screw it into the case. Thanks, Mark Hagler

Good day all We got a Wildcard TE110P I installed linux,zaptel,libpti and asterisk I coped over my zaptel.conf and zapata.conf from a previous E100P config But when I try to start asterisk it gives error not bying able to load zap channles: == Parsing '/etc/asterisk/zapata.conf': Found Jan 10 08:17:18 WARNING[-1084595552]: chan_zap.c:9308 setup_zap: Ignoring switchtype Jan 10 08:17:18