similar to: GXP-2000 Phones with Cisco 3560 PoE Switch

FYI, spoke with Grandstream this morning, the GXP-2000 release has been delayed again. Looking like April now before these hit the street. -- Cory Andrews Senior Partner VOIPSupply.com +++++++++++++ V: 800.398.VOIP X22 F: 716.630.1548 E: Cory@VOIPSupply.com

Hi all, For a top quality setup, I will need to install high quality VoIP switches with QoS and PoE. My potential customer should not have any problem with call quality. Experienced folks, Please advice me what switches to install and at what price. I may need it for upto 100 phones. What else should I consider so that phones work without problem along with the computers on the same network?

Hello people, I am having difficulties figuring out the POE power draw in watts from a Polycom IP601. I want to know how many IP601's can be powered from the Cisco Catalyst 3560G-48PS. The IP601 wallwart has: Input 120VAC 60hz 19W, Output 24VDC 500mA. I assume the output is appropriate value to figure out how many phones can be powered. The Cisco 3560 datasheet says "the 48-port PoE

> > Allen Casteran wrote: > > Anyone know what the POE draw is for the Aastra 480i phones? > > We have switches that will do 15 watts on 12 ports but only do 7.7 watts on all 24 ports. > > A Cisco 3560 switch will do 15.6 watts on all 24 ports. > > Just trying to find out if we need that much power. > Drew wrote: > According to Aastra tech support, 5 watts

Hi, Do you need a special cable and power for that unit or you can run it of PoE Switch? Thanks. robert

I know this is on the wiki, I just want to confirm so I don't blow up my cisco phones. I've got several cisco 7940's all running using cisco power cubes. However, my boss wants me to switch just a few over to poe, but doesn't want to fork out the dough for a nice cisco poe switch, or anybody else's poe switch for that matter. So my question is, what is the '99.999%

Anyone know what the POE draw is for the Aastra 480i phones? We have switches that will do 15 watts on 12 ports but only do 7.7 watts on all 24 ports. A Cisco 3560 switch will do 15.6 watts on all 24 ports. Just trying to find out if we need that much power. Can't seem to find any info on the Aastra site. Comments?

>From the usual place, http://www.grandstream.com/BETATEST/GXP2000/ Note, there are two (and it took me a bit of a while to figure out) images to be loaded. Copy the ...a.bin's and the .bin's to your http provisioning directory, and reboot. The phone _must_ load the .bin files before it understands the ..a.bin files. After it loads the first one, the phone does lock up with the

Hi, i got my Grandstream GXP-2000 phone today and want to configure it with TFTP. I downloaded the firmware 1.1.0.13 and put it into my tftp-server directory. Then I downloaded the template from: http://www.grandstream.com/DOWNLOAD/Configuration_Tool/Linux_Unix/Grandstream_Configuration_File_Template_1.0.6.x.txt renamed it to cfg<mac-address> Did the configuration in the new file and

I have 5 GXP 2000's with firmware 1.1.4.25 running with Asterisk 1.4.13. Is anyone else getting the following error in the asterisk console: [Oct 22 11:39:01] WARNING[7100]: rtp.c:1142 ast_rtp_read: RTP Read too short every couple of seconds when a handset is in a call? I didn't notice this happening when I was using an older GXP2000 with the same firmware (doesn't mean that it

I'm using a few GXP-2000 with firmware 1.0.2.13 and everything seems to be working fine. However, there are a couple of issues I'd like to know if are possible: 1) Even though the phone has 4 line appearances, if I am speaking on a line, the phone can no longer receive phone calls. I can manually select another line and make calls, but when Asterisk tries to send a call to it, I

I was looking at the aastra 9133i, however I was informed that this phone is no longer supported. What are good phones around the $100 - $125 price point? (Need POE) Thanks, David Ruggles CCNA MCSE (NT) CNA A+ Network Engineer Safe Data, Inc. (910) 285-7200 david at safedatausa.com

I have been struggling with this issue for about a year now. There were just too many IP phones to choose from at all sorts of price points and not enough information about any of them. Now I am looking at the situation again and if anything it has gotten worse. There are even more phones and all sorts of opinions. For every person that says phone x is great there is someone else complaining

I am looking to replace all of the old "Bell" (POTS) phones in my home and office with IP phones. As you can imagine I don't have a huge budget to work with but I want phones that will provide acceptable voice quality and durability. There are basically three categories as I see it 1. satellite phones (low cost, low function) 2. primary domestic phone (good quality, POE capable,

I recently posted a question RE the Sipura 941 and using different ring tones, Thanks to hads I managed to use SET(_ALERT_INFO=Classic-1) to achieve this but trying this on the GXP 2000's didn't seem to do the trick?? Has anyone one had any luck on this topic? Also haven't been able to find any info on an auto-answer for the GXP 2000, again, I have succeeded in doing so with the

Hi all, I am looking for phones witch support POE, with a good relation between quality and price to work with asterisk. I just see the Thompson st2030 and the Linksys SPA 922 an SPA 942. Witch of this phones or another ones gave you the best results in a productivity enviroment? Thanks in advance. VoipCrazy. -------------- next part -------------- An HTML attachment was scrubbed... URL:

I've tried to use a Cisco power injector to supply power over Ethernet to a GXP2000 phone without success. Although when I plugged these phone to a PoE capable Cisco Switch it worked without a problem! Knowing that all these three equipments implement IEEE 802.3af protocol, why doesn't it work with the Cisco power injector? Anyone also had this problem before? Thanks, Ricardo Carvalho.

Hi, I'd set the daylight saving option to yes on all the GXP-2000 phones, but apparantly it doesn't move it an hour back on last sunday of October. So now I am stuck will all the phones showing the wrong time. Isn't there an option so that it'll automatically update daylight savings? Thanks -- Zeeshan A Zakaria -------------- next part -------------- An HTML attachment was

Just got a call from a company in Warren, MI . They recently had an Asterisk system put in by a vendor, and are having issues which need analysis and correction. They have a tremendous sense of urgency. They have about (40) users, and need DID's assigned to extensions and are having some echo issues at the site. If anyone is in the Warren, MI area, and is interested in some cavalry work,

3com have some goods POE kit and some very nice managed wall jacks that supply POE and are fully managed. Here's an auction that the seller just closed:- http://cgi.ebay.co.uk/ws/eBayISAPI.dll?ViewItem&category=40990&item=5708757277&rd=1&ssPageName=WDVW Last time I spoke to him he had 5 boxes of 20 units and was willing to sell them at around $575 with a bit of arm twisting.