similar to: Limit on SIP phones on one server

I have a handful of 7912's connected to my asterisk 1.2.14 server. (6 to be exact). I get the X on the display sometimes for loosing registration. I have the config file for the 7912's SipRegInterval: 60 and asterisk is the default. ; maxexpirey=3600 ;defaultexpirey=120 I've not changed them. How can I keep these phones online and stop loosing registration? Thanks, Jerry

I have 3 phones P1 is a non video phone - grandstream P2 is a Grandstream GXV3000 P3 is a Grandstream GXV3000 Using P1 to place a call to P2 I get audio only (as expected). Then on P1 I transfer the call to P3 and I still only get audio. At this point shouldn't the two video phones P2 and P3 say to each other we are video and so startup the video stream??? This is not working at this time?

Hi all, I have setup my Cisco 79XX phone. Did the tftp, put the config files in the right location with the right names. Booted my phone, it does the tftp things, the screen shows my extensions everything seems fine. However, when I come offhook and try to dial 11 which is just a playback of demo-congrats in the dialplan the phone says Calling Out (INV) below is my sip.conf file - I presume it

Howdy, I am attempting to isolate the location of a memory leak in a 4GL program, and have hit a bit of a snag. When I LD_PRELOAD libumem and run the application server, "::findleaks -fdv" reports numerous leaks: CACHE LEAKED BUFCTL CALLER 0000000100b49068 15 0000000100ef2d50 fdcon+0x6c4 0000000100b50028 1 0000000100b72ac0 fdcon+0x6c4 0000000100b49068

I "wish" to not load the or even install the nouveau driver by default. I want to use the NVIDIA binary driver. I have tried a number of things: 1) in my kickstart package section add the line: -xorg-x11-drv-nouveau This did not work - it was still installed. 2) use the nvidia installer and it asks to create a modprobe.conf file to blacklist the driver. I said yes thats what I want.

I tried install 4.4 on an old Via 800mhz box. i386 of course. The installer dies pretty quick. I thought the via was i386 compatible? Is there something special to do. Jerry

I have a Cisco 7960 & IpDialogs that I am not able to use the transfer button on it. What happens is that it puts the call on hold and then it gives you a dial tone. You can dial but it will not transfer the call. What we are trying to do is transfer to extension 700 for parking so another person can pick up the line. We can not use the # key to do this due to we have several IVR's

I have used WIP300, hitachi 5000 wireless phones on asterisk and have had good success. However, I am looking for a WIFI phone with integrated belt clip. Has anyone found any? I have tried after market clips and holders and those just don't work. THanks for sharing if someone has found something that works with asterisk. Jerry

I am sending an email from my machine devcentos5x64. the transcript below (hangs for 60 seconds) at the line: MAIL From:<root at devcentos5x64.msgnet.com> SIZE=56 AUTH=root at devcentos5x64.msgnet.com The email succeeds - but I am trying to figure out the 60 second delay. Neither email server is busy. Nothing is waiting. the DNS on both machines point to the same nameserver. The DNS

Howdy, I just installed the crossbow snapshot from opensolaris.org, and bumped into an issue when attempting to create a virtual nic: $ dladm create-vnic -i 192.168.1.101 -d ni0 2 dladm: VNIC creation failed: No such file or directory (unknown diagnostic) When I truss the process, it looks like it''s failing when attempting to open the vnic pseudo-device: 100878/1:

I am getting a SIP 401 unauthorized message. My public IP or PIP is being pre-routed with iptables to goto an internal IP or IIP All the polycom phones in the office point to the IIP. they work fine. I have 2 external phones that are registering to the PIP. I see the register attempt as I am getting the 401 unauthorized message. For the 2 external phones both have nat=1 enabled. remote phone

What cpu/memmory configurations have people had good luck with for a small office asterisk server... (polycom's/poe linksys) Dell's got their $200 SC440 going again until the 12th... and I'm thinking it might be just the ticket...

Hello I have one phone (phone1) in one network, the other (phone2) in public network. both can call the other side; phone1 can be heard by phone2, phone2 can't be heard. I don't have NAT set on both end, but I use rtpproxy on SER. Is NAT still necessary to be set on both phones? Thank you! steven

Hi, sometimes I have one way calls and noise between sip phones connected to the same LAN so no nat/firewall is involved. I tried with different sip phone models soft phones and the result is the same. I searched inside every log file but found nothing. I made different PBX with different hardware but the result is always the same. Is there anybody experiencing this terrible problem?

Using asterisk 1.4 with 100M or 1000M ethernet and 230 SIP clients and a 64 bit 4200+ box would there be any noticable lag or delay to bring each one of them into a PAGE mode. so one speaker can talk out on all 230 SIP clients for a message. Would this work? Thanks, Jerry

how do I prevent gnome_panel from starting up? once its started I can do "gnome-session-remove gnome_panel" But I dont want it to startup at all. How can I do that? jerry

Hi, I have mentioned before that we have added some sdt dtrace probes in SAX, our APL interpreter. Encouraged by Angelo and Jignesh, I have created a small document (5 pages) describing our experience with it, together with some problems we have encountered and some scripts we use for pretty-printing dtrace outputs. The said document can be found at

Can someone, more learned in the ways of dtrace point me at what to look at to help understand why the kernel on one machine is using tons of memory, while another machine doing the same task/same user load is not. swapinfo for the "afflicted" machine shows RAM _______Total 16384 Mb RAM Unusable 73 Mb RAM Kernel 9226 Mb RAM Locked 2 Mb RAM Used

To continue here with problems on this compaq v2000 laptop, I put kernel source on a USB disk and plugged it into the v2000. NOTHING IS recognized. I tried to manually mount the disk and nothing either... I thought USB was well established.... I thought trying to recompile the kernel for realtek support might get my networking going... I am stuck??? Jerry -------------- next part

A small script to see what SCSI commands are being issued by a system: http://blogs.sun.com/roller/page/chrisg?entry=scsi_d_script Still work in progress as I needs to handle larger CDBs but it is a start, since I don''t have a disk that big it is not a problem for me yet. Also getting the return scsi packet is a hack but so far I can see no alternative short of knowing about all the