similar to: Customisable In-band ringing?

I recently read about the following new technologies from Digium. Has anyone tried the new HPEC or knows when it will be available? TDM800P and HPEC The TDM800P is an 8-port analog telephony interface card, so it fills the gap between Digium's 4-port and 24-port cards. Analog phones and POTS lines are going to be with us for some time, and demand for support for them remains high. The

I have progressinband=yes in sip.conf, but Asterisk sends a 180-Ringing to my polycom phones and then it also sends 183-Session Progress. That doesn't seem to make sense. Shouldn't Asterisk NOT send 180-Ringing if progressinband=yes ? Doug.

Hello, Has anyone tried the combination of asterisk 1.2.24, zaptel 1.4.5 and HPEC 9.00.003? In particular, with a hardware configuration similar to: Module 0: Installed -- AUTO FXO (FCC mode) Module 1: Installed -- AUTO FXO (FCC mode) Module 2: Installed -- AUTO FXO (FCC mode) Module 3: Not installed Found a Wildcard TDM: Wildcard TDM400P REV I (3 modules) I have two fully independent systems

Hi people, I would like to read your suggestions as to where the issue might be. ATA286=Grandstream Budgetone ATA 286 in SIP mode. One Lan Port and one FXS port. TDM04B= 4 FXO signal fxls There is a 8FXO-to-SIP unit in this scenario that works perfectly so i will not make mention of it. PSTN----VOIPprovider---Internet---ATA286------tdm04b---Asterisk1.2.-13 Asterisk is being used as a meetme

Hello, My target system is : PSTN <---> Sip Provider <---IP/ADSL---> Router with fw/NAT <--- SIP/IP/Eth --> Asterisk <--- SIP/IP/Eth --> SIP Phones Asterisk is configured to keep NAT connection with SIP provider open (with qualifyfreq) so I don't have any problem (yet) with either casual incoming or outgoing calls. To work around a possible No Audio when an incoming

Andrew, I don't think it's a Polycom issue. We took Asterisk out of the picture and had our Polycom phones communicate directly with an Audiocodes PSTN gateway. Unlike Asterisk, the audiocodes do not send 180 Ringing before sending 183 Session Progress, and the polycom's play the correct tones in this case. We WANT Asterisk to send progress tones in band. In our case it IS needed.

Hello, I just installed a PRI and when I make a local (seven digit) call, I get Code 28 back from the telco, (I believe code 28 means "Invalid Number") and I hear a fast busy on the phone. Here is the output: -- Executing Dial("SIP/marke-17b1", "ZAP/G1/4967171") in new stack -- Requested transfer capability: 0x00 - SPEECH -- Called G1/4967171

Hello! I migrated asterisk 11 to 13 as user of FreePBX 12.0.76.2. As customer of German Telekom, I have three numbers and therefore three trunks - each number is bound to one trunk. After migration, some callers complained about missing ringback tone: they didn't hear any ring tone and where surprised that they suddenly got me anyway :-). The connection afterwards was as expected. Deeper

> Hmmm... I have this aweful feeling that I'm choosing the > exact wrong time to ask a "newbie question" :) Oh well, here > it goes. > > The quick question is : "How do I dial an extension?" > (answer is probably - "you don't" in which case:) "How do I > dial my asterisk box?" - I have no outside line, I just want >

Whoops, email client auto-filled dev previously. Let's try this again. Michael Maier wrote: <snip> > Ok - but this doesn't seem to answer my main question: > > Why must > > progressinband=never > > be applied especially if asterisk uses it by default? The big difference > between w/ and w/o it is: The default in 13 is "no" which still

Hi all I've got an issue where when I call a number that just plays early media back to me. Instead of hearing the full sequence of tones I hear a short ringing then part of the sequence. What seems odd is that I can see the telephone-event/8000 being passed up the chain but when it gets to Asterisk, it is never sent back to the phone. Instead I just see the usual RTP flows. I've been

Hi All, I've been looking for information on how to use asterisk and early media to allow for a video-preview of the caller at the callee's phone for days... but I haven't been too successful :( I found that there seems to be a company "2N Helios IP" which claims (youtube-video) that "their" SIP server is able to provide early video (using a Grandstream 3157v2

Chris Abel writes: >Hello everyone! > >I've had this problem for a while and cant figure it out. When an outside >caller calls an extension on my asterisk system, they do not hear any >sort of ringing. Inside extensions calling other extensions do hear >ringing. We have 3 other asterisk systems that are configured the same >way, but do not have this problem. We think it

I'm evaluating using Polycom phones for our call center and I've set up my first phone (a SoundPoint 560) to give it a try. The phone is working and can successfully place and receive calls. But every minute, there's an error in the log file: chan_sip.c: Registration from '<sip:6193644850 at jtsd05>' failed for '192.168.200.99' - Username/auth name

I have about 20+ phones on a server, all set for registry expiry 1 min. But only this one, with 2 accounts, keeps re-registerting itself. All the time this is what I see on asterisk CLI and it is kind of annoying. What only this phone does this and no other. Its on a remote location. All phones are Grandstream GXP-2000. -- Registered SIP '502' at 64.101.221.250 port 18639 expires 60

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 This is slowly driving me nuts! I have several Cisco 7960s with SIP 8.2/7.5 fw connecting to Asterisk 1.2.5 driving a TE110P on a BT EuroISDN PRI line. On all outgoing calls I get a double ring tone (UK style + US style). I also have a DECT phone on a Sipura SPA-3000 configured with UK tones. This gives me a double ring of UK + UK, so this

I have Polycom ip-300 phones that worked yesterday but dont seem to work today (at least dtmf signalling once connected to the asterisk box) The current configuration is: [general] port = 5060 bindaddr = 0.0.0.0 context = test srvlookup = yes dtmf = inband allow = all dtmfmode=inband progressinband=no disallow=all allow=ulaw pedantic=no [202] type=user secret=xxxx context=test mailbox=202

Any ideas on why callers who call into my customer's SIP trunk are not hearing a ringback tone? I had this on one other asterisk system, and wound up needing to set progressinband=yes in the SIP trunk config. I have set this on the current system & restarted asterisk, but to no avail. I am using: AsteriskNOW distro Asterisk build is 1.6 from AsteriskNOW repository:

I have this in sip.conf: [general] context=default allowoverlap=no bindport=5060 bindaddr=0.0.0.0 srvlookup=yes progressinband=yes [19256002182] type=friend username=19256002182 callerid="Test hone 1" <+19256002182> host=dynamic canreinvite=no secret=password context=test disallow=all allow=g729 [level3] type=peer host=xxx.yyy.16.99 context=default

Hi all, using * 1.2.9.1 and this week all of the sudden calls keep ringing even after they've been picked up... Here's one users summary: When I pick up the phone, I hear a dial tone and I am able to dial out. But for some odd reason, the receiving line picks up while the outgoing line is still ringing. And the receiving line can hear everything while the phone is still ringing. I tested