similar to: Dell PowerEdge 2950 Sharing NIC IRQ with Digium Card

The only PCI-X card I have is an old ICP Vortex RAID controller and the Dell hangs with that installed (BIOS is disabled). It's only for a tape drive so performance isn't really an issue. thanks

I have CentOS 5 installed on a few Dell PE2950 systems. ? ?The SMART daemon claims the drives included with the server do not support SMART, which rather surprised me. What, then, are my options for monitoring the health of the server hard drives? ?It would be nice to have some service running I could email to myself on the status of each drive. Thanks. Scott

Does anybody have Digium TE212P interface card on Dell PowerEdge 1850? I'm planning to install * on that configuration so I'm looking for any positive/negative experience. Best regards, -- Tomislav Par?ina Lama Computers Split Stinice 12, 21000 Split Tel.: +385(21)270248 Mob.: +385(91)1212148 SIP: tomo@sip.lama.hr e-mail: tparcina#lama.hr http://www.lama.hr

I''ve idendified the problem... description: problem in XEN bridged-network. Dom0 doesn''t respond at external network activity (DomUs may work correctly) problem: something related to Broadcom NetXtreme II menagement solution: follow all this instructions: http://article.gmane.org/gmane.linux.hardware.dell.poweredge/23276 bye, s.

hello all, I have been trying to set-up bridged network with VLAN and not able to succeed as many tutorials address only single NIC. I am trying to setup 2 guests (backtrack instance) each guest has NIC1 and NIC2. following is snippet for guest1 I am not able to get 192.168.0.2 address back on guest eth0. VIRT-MANAGER GUI : guest1-lan details radio button left side panel NIC1

Ok, the story is this, I''m running an Unreal Tournament 2004 server. It''s running on a system that has two external NICs that are connected to different ISPs. I would like players to be able to connect to the server from either link. My default gateway goes through NIC1. For traffic through NIC2 to work I simply added an extra routing table and rule. The extra routing table has

Hi, I was planning on getting a Dell PowerEdge 2950 for our new Asterisk configuration. But while searching for documentation about it and/or reported issues, I found this: http://www.voip-info.org/wiki/view/Asterisk+hardware WARNING - many Dell motherboards use the e1000 gigabit ethernet chipset, which has been known to cause random locksup - if you plan on using a Dell server, disable the

On Wed, 12 Aug 2020 21:46:19 +0800 Turritopsis Dohrnii Teo En Ming <ceo at teo-en-ming.com> wrote: > Subject: [Sharing] CentOS 8.2 (2004) Linux Server is Compatible with > Dell PowerEdge R640 1U Server This server should be fully ok to run RHEL8 and CentOS8. What exactly goes wrong? https://access.redhat.com/ecosystem/hardware/2941651 /Peter K > Good day from Singapore, >

Subject: [Sharing] CentOS 8.2 (2004) Linux Server is Compatible with Dell PowerEdge R640 1U Server Good day from Singapore, I have just installed CentOS 8.2 (2004) Linux Server on Dell PowerEdge R640 1U Server for "Donald Trump and Xi Jinping Investment Company LLP" (fictitious/fictional company name used) in Singapore on 11 August 2020 Tuesday. I can confirm that CentOS 8.2

Hi all: I've been developing and testing on a tdm400p card and it's been going well. As you probably know, the tdm400p needs an ide power supply, but the dell poweredge 2600 that this card is destined for eventually has all the power supplied on the backplane with no ide cables. The thing is, on the motherboard in the server, there is an ide ribbon connector, and beside that, something

Hello everyone, I'm trying to add a second DC to a Samba 4 AD: they both have multiple NICs and for this reason cannot find a way to make it work. They communicate through VPN and both have one of the bound interfaces set to the same IP address, 172.20.0.1, which doesn't allow me to route to the correct DC, and that is only part of the problem. Here is the configuration: *

I add some additional information I didn't give in my previous email, specifically how I tried to force DC1 and DC2 to contact each other only with their VPN IPs. I did so using dnsmasq as a DNS proxy. # DC1 configuration IP NIC1: 172.16.0.2 IP NIC2: 172.20.0.1 IP VPN: 172.19.1.173 --- /etc/resolv.conf: search domain.local domain domain.local nameserver 172.19.1.173 --- I configured dnsmasq

Hello everyone, can someone please tell me if the configuration previously shown is eventually going to work? Stefano Il giorno lun 19 ott 2020 alle ore 18:56 Stefano Vargiu < vstefanoxx at gmail.com> ha scritto: > I add some additional information I didn't give in my previous email, > specifically how I tried to force DC1 and DC2 to contact each other only > with their VPN

hi i m trying to install centos5 on my poweredge 2950 with no luck. the raid controler is LSI Logic / Symbios Logic MegaRAID SAS 1078 (rev 04) indeed all is going fine during the installation but when i reboot the server panic the first error i got is this one error mounting /dev/root on /sysroot as ext3: block device required it seems that it can't find the /dev/root devices. but when

Hi, I've just joined the list because of questionnaire in the forum [1]. The hardware is AMD-V(IOMMU) capable and is enabled in the BIOS with 3 NICs. I currently have host Windows 2008 R2 installed but binds (network services and protocols) on NIC3 only. My guests on VMWare workstation (has bridged network service bound on all 3 NIC) has bridged 3 NICs for the guests where NIC1 is WAN, NIC2

Hi All Before I go out and buy a DELL PowerEdge 2850 has anyone had problems (or any other useful experience) getting a TE411P to work with it. I also have a legacy TE110P. Has anyone had problems with this combo. -- Dr. Rodney G. McDuff |Ex ignorantia ad sapientiam Manager, Strategic Technologies Group| Ex luce ad tenebras Information Technology Services | The

I am having an issue with Megacli when adding or removing virtual disks. I will post a link to fpaste that has the issue shown. In brief whenever i add, or remove, a virtual disk via MegaCli the attempt succeeds and the adapter is configured but the OS remounts dm-0 in read only. dm-0 is my root lv. This issue does not happen if i boot into the default, non Xen, CentOS kernel. On stock

On Mon, Oct 19, 2020 at 7:42 AM Stefano Vargiu via samba <samba at lists.samba.org> wrote: > > Hello everyone, > > I'm trying to add a second DC to a Samba 4 AD: they both have multiple NICs > and for this reason cannot find a way to make it work. > They communicate through VPN and both have one of the bound interfaces set > to the same IP address, 172.20.0.1, which

It's Digium, not Dell. I have two identical Dell 1850s, each with the allegedly offensive built-in E100 Ethernet ports. I placed a TE410P card in each. One worked great, the other would not modprobe. Upon examination, we discovered that the two TE410P cards had different firmware revisions. Turns out the one with the older version was the one that worked. We sent the second card back

Hello, Just chiming in here: >From: asterisk-users-bounces@lists.digium.com >[mailto:asterisk-users-bounces@lists.digium.com] On >Behalf Of >bdolljr@bigskytech.com >Sent: Viernes, 22 de Julio de 2005 01:24 p.m. >To: Asterisk Users Mailing List - Non-Commercial >Discussion >Subject: RE: [Asterisk-Users] Dell Hardware >> Mmhh nice !! So, why did Digium forbid it :)?