similar to: Misdn instability with asterisk 1.4

Hi. I'm running Asterisk server with 10 sip phones, and 2 grouped T0 lines with 10 DDI numbers. My provider is France Telecom and my setup is : - Debian Lenny - Asterisk 1.4 - Linux kernel 2.6.25.17 - mISDN 1.1.8 driver - Sip phones Thomson ST2030 No problem with the SIP . But when reveiving a call on RNIS line (any of the DDI numbers), the associated SIP phone rings indicating _two_

Hi, i use an BN4S0 with misdn an asterisk on Linux 2.6.9. The hfcmulti module is loaded with option: type=0x04 protocol=0x2,0x2,0x22,0x2 layermask=0xf,0xf,0xf,0xf and the fourth port is connected to an ISDN PTMP (MSN) port. Call to #72 from S0 (BN port 4) are not accepted from asterisk but why ? Can anyone give me a hint ?? misdn debug messages follows: lib: NEW_CR Ind with l3id:80001

Hello I fixed my problem. I changed user and group in /etc/mISDN.conf: <devnode user="asterisk" group="asterisk" mode="644">mISDN</devnode> now it works again! Thanx 4 help! ;) Ingrid -- "Bonnie & Clyde der Postmaster-Szene!" approved by Postfix-God http://wetterstation-pliening.info http://dokuwiki.nausch.org --------------

i am using asterisk 1.6.2 with mISDN and a passive AVM Fritz!card on CentOS 5.5. The only thing, i want to do is a call-redirection from an isdn-call to my mobile via sip-account. My extension conf is: general] static=yes writeprotect=no [globals] OUT_PORT=1 [ISDN] exten => 12345,1,Dial(SIP/012346737222 at sipprovider.local) If i call to the msn 12345, the SIP-call is going out, but after

I'm trying to set caller ids on outgoing calls. I have a quad BRI B410P card connected to my telephony provider. I know the list of DID numbers the provider assigned to my company. If I don't set the caller id then the callee always sees the same "top-level" number. If I set the caller id to a specific DID number we own, the callee keeps seeing the "top-level" number,

Use Set(CALLERID(num)=9999999999) instead of using CALLERID(all). Remember to set this BEFORE you Dial. -->> -----Original Message----- -->> From: asterisk-users-bounces at lists.digium.com [mailto:asterisk-users- -->> bounces at lists.digium.com] On Behalf Of Vieri -->> Sent: 06 February 2009 12:36 -->> To: asterisk-users at lists.digium.com -->>

You're quite right. We'll need to see your misdn.conf file to check the settings. -->> -----Original Message----- -->> From: asterisk-users-bounces at lists.digium.com [mailto:asterisk-users- -->> bounces at lists.digium.com] On Behalf Of Vieri -->> Sent: 06 February 2009 13:49 -->> To: asterisk-users at lists.digium.com -->> Subject:

hi i've configured a Beronet BN8S0 Card with misdn beronet utility. the card is configured with all lines in TE and P2P mode, and it is connected with the special cable with an ISDN connection. i've turned on debugging to level 4, this is the output from the asterisk cli when i receive a call: P[ 5] MGMT: Short status dinfo 1000001 P[ 5] MGMT: SSTATUS: L1_ACTIVATED P[ 5] handle_frm:

Hi, I've been having problems getting Asterisk to work with a fritz card (in ptp mode). We've managed to get everything configured, however, as soon as the call is connected we get "Unhandled message: prim 281 len -22 from addr 1000000, dinfo 0 on this port" I checked, and mISDN_dsp is loaded. Any help would be much appreciated! Regards, Chris Jones // Network Administrator

Hi all, we're buildin an Asterisk box based on an Intel IXP425 board. The board uses a Beronet BN2S0 ISDN card, mISDN 1.1.4 and asterisk 1.4.2. hfc_multi has been patched to compile under big endian cpu, and so also capi kernel files. All the modules seem to load correctly (configuration was made with misdn-init config), but when starting cha_misdn, asterisk outputs the following lines: P[ 1]

We have ISDN PCI Adapter from Billion(using mISDN). When we connect it to the PSTN the incoming calls are OK. When we try to make a call we can't do that because the ISDN port is Down: CLI> misdn show port 1 BEGIN STACK_LIST: * Stack Addr: 40400001 Port 1 Type TE Prot. PMP L2Link DOWN L1Link:DOWN Idx: 0

Hi. I want to handle incoming chan_misdn traffic by asterisk, but I've got message - 'Extension can never match, so disconnecting'. What I'm doing wrong ? How I can pass incoming dialed number (dad) to misdn context (in my case 'dss1_incoming') ? Works unrouted calls (s extension) if I set immediate=yes in misdn.conf, but I want to route calls by dialed number. log

_____ Von: Pascal Speck [mailto:p.speck@ewersbach.net] Gesendet: Montag, 5. September 2005 10:37 An: 'asterisk-users@lists.digium.org' Betreff: Timeout when Dialing - HELP When i try to do a call I get this message after a few seconds: I IND :TIMEOUT pid:1 mode:NT addr:51400102 port:2 --> l3id:10040 cause:16 dad:800759 oad:20 channel:1 port:2 --> lib: prim 34582

I am trying to use misdn insted of zaphfc to drive two billion isdn cards zaphfc is ok, but the problem with cdr and the fact tha you always have to wait the bristuffed version of asterisk took me to try another way. so I downloaded the misdn installation script from beronet for the last version ( I am using asterisk stable 1.2, so now is 1.2.5) wget

Hi, I have installed Asterisk 1.4 with mISDN with the install-asterisk.tar.gz script from beronet.com. On my system I have two cards, one a AVM Frit!Card Pci 2.0 and one HFC-S chip. I know both to work well with mISDN on my system from a previous installation. Now however, the AVM card works well at first glance, i.e. it "registers" incoming calls and works through the asterisk

Hello everyone! I'm sorry I can't be more specific. So here's the setup: a Samsung router with analog and ISDN ports. the phone company says the outgoing line is analog landline, but I'm sure it's some VOIP. so connected to the ISDN port of the router is a Fritz AVM card, used with mISDN. when I try to make a call with asterisk I get something like this: cli>>

Hi i've installed this software: ******************** SOFTWARE mISDN-1_1_7 mISDNuser-1_1_7 Asterisk-1.4.15 ******************** SOFTWARE misdn is correctly loaded by misdn-inist start Here there is the misdn.conf (copied from an existing and working installation with Asterisk 1.2.x and one BN8S0) ******************** MISDN.CONF [general] misdn_init=/etc/misdn-init.conf debug=0 bridging=no

Hi i am upgrading an asterisk server from 1.2.4 to 1.4. i've installed libpri 1.4 i've installed zaptel 1.4 I've installed the new version of misdn with the script of beronet. i use this configure script: ./configure --with-postgres=/usr/local/pgsql then: make menuselect [*] 1. cdr_csv [*] 2. cdr_custom [*] 3. cdr_manager XXX 4. cdr_odbc [*] 5. cdr_pgsql XXX 6. cdr_radius

HI, I tried to configure Asterisk 1.8 on one of my test-hosts. I've installed from centos-asterisk.repo (http://packages.asterisk.org/centos/$releasever/tested/$basearch/): Nov 26 15:34:56 Installed: asterisk-sounds-core-en-gsm-1.4.20-1_centos5.noarch Nov 26 15:34:59 Installed: asterisk18-core-1.8.0-1_centos5.i386 Nov 26 15:35:02 Installed: asterisk18-voicemail-1.8.0-1_centos5.i386 Nov 26

Hi, I try to compile mISDN 1_1_9_2 (kernel: 2.6.32.13). I had the following compiling error: make[1]: Entering directory `/usr/src/linux-2.6.32.13' CC [M] /usr/src/mISDN-1_1_9_2/drivers/isdn/hardware/mISDN/sysfs_obj.o /usr/src/mISDN-1_1_9_2/drivers/isdn/hardware/mISDN/sysfs_obj.c: In function ?mISDN_register_sysfs_obj?: