similar to: Red alarms

About every hour I see the yellow alarms on all or a number of channels of my PRI which is connected to the dutch telephony network, Asterisk keeps on working fine.... Here's an example where channel 1-24 went into alarm: WARNING[90124]: File chan_zap.c, Line 4139 (handle_init_event): Detected alarm on channel 1: Yellow Alarm WARNING[90124]: File chan_zap.c, Line 4139 (handle_init_event):

Here is the scenario: Asterisk 1.14.13; zaptel 1.4.6; Digium TE120P (same problem with various previous versions; same problem with different TE120P cards). The customer has a partial (10 B-Channel) PRI that when it is busy (eight or more B channels in use), tends to fail as shown below... [Jan 26 23:00:31] ERROR[31893] chan_zap.c: Write to 28 failed: Unknown error 500 [Jan 26 23:00:31]

Hi everyone, I have a PRI conection on an * system running Asterisk 1.0.9, libpri 1.0.9 and zaptel 1.0.9.2 connected to an AXE 10 (APZ 21220 System 64) in the network side. I know the system and the wildcard I´m using are ok because I´ve used them before with other PRI connections (to a Siemens EWSD) without any problem. First the PRI didn´t work (I got the TE110P alarmed with red). After

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi. I'm getting the following error at random intervals on my TE410P with Asterisk CVS-03/30/04-11:49:01-CEST. I have two spans active, one connected to my Telco, the other to a Siemens PABX. Both spans display this behavior at random intervals. All calls are dropped when this happens. Spans are not necessarily in use when this happens.

Calling out on PSTN over a TDM400P seems to generate a Red Alarm - whatever that is. I have another extension on the PSTN, and I can dial out over that. zttool shows no alarms. asterisk*CLI> zap show status Description Alarms IRQ bpviol CRC4 Fra Codi Options LBO Wildcard TDM400P REV I Board 1 OK 0 0 0 CAS Unk YEL 0 db

Guys.. I just saw this for the first time... I did some google and wiki without any luck.. what does a red or yellow alarm mean in zaptel? Feb 23 02:54:16 WARNING[16890]: chan_zap.c:5865 handle_init_event: Detected alarm on channel 2: Red Alarm Feb 23 02:54:24 NOTICE[16890]: chan_zap.c:5860 handle_init_event: Alarm cleared on channel 2 This just happened by itself..

Hi All, For the most part, the PBX works as it should. Occasionally people complain that they call and the PBX doesn't pick up. Other times it looks like the call is answered by Asterisk but I still hear ringing and I start listening to the IVR menu a few seconds into it. As for Asterisk not picking up, I see the following in the logs: [Mar 27 13:32:29] NOTICE[13197]: chan_zap.c:7071

Hi guys, I've been trying to get my ISDN-10 line up for the past few days, but its been going up and down. I am using OpenVox D110P card on asterisk version 1.4.21. It seems to me like a cable problem. I tried using Ethernet straight cable (12, 45, 36, 78) and also a "straight" cable where the twisted pairs are on 12, 34, 56 and 78. The problem remains the same.

Hello - I have a Premisys Slimline Channel Bank connected to a Digium TE110P. I am not able to call the FXS extensions or get dialtone on them. The channel bank is connected via a T1 crossover to the cable and lights show green. I really need to get this functioning by end of day. If anyone can help me out I would be greatly appreciative. Thanks, Dave zaptel.conf loadzone =

Hi I have a Panasonic TDA600 conected with one E1 to the pstn and one PRI with my Asterisk using a Digium TE220B card. The Panasonic is master clock and Asterisk is slave, additionally the Panasonic takes the clock from the PSTN E1. This scheme works and I?m able to make and receive calls the problem is that some times the Asterisk lose the synchronism with the Panasonic and the log shows this

Hi, For a significant time now (since about 0.2.0-rc8n) the qozap driver has become very verbose if an ISDN line is not connected... I get the messages below every couple of seconds in the asterisk logs. The "flaw" in the messages is the "Alarm cleared" message - The alarm cannot possibly be cleared because there is no physical media connected into that port!!! (BTW - All

Hey, I wrote yesterday about PRI dropping, which turned out to just be a regular reset of unused B-channels. This time there's a real issue. As noted earlier I have an ISDN-30 connection, a Digium TE-121 with VPMADT032 echo cancellation. These are my configurations files: == /etc/zaptel.conf loadzone=dk defaultzone=dk span=1,1,0,css,hdb3,crc4 bchan=1-15 dchan=16 bchan=17-31 == ==

Hi list, Sometimes I receive a Red Alarm in my E1 trunk (E&M immediate start signaling), and just few seconds after this, all alarms are cleared. This problem ocurrs many times/day, and if are calls in progress, these calls just hang-up. Could it be an asterisk bug? Or may I contact the PSTN provider? Thanks Eduardo

I just had the same exact problem this morning. The only thing I've done in the last couple of days is update update zaptel. I rolled back my zaptel to 2/11/04 from 3/8/04. And kept my libpri from 3/8/04. I never had this error before updated. I had other issues, but not this one. -sb -----Original Message----- From: asterisk-users-admin@lists.digium.com

Hello my friends, I would like to understand the output from "pri intense debug span X", the Telco always says that their side is OK, but i always receive alarms, loosing connection, take a look: [Sep 16 13:18:19] WARNING[30364] chan_zap.c: Detected alarm on channel 1: Recovering [Sep 16 13:18:19] WARNING[30364] chan_zap.c: Unable to disable echo cancellation on channel 1 [...] [Sep 16

I need your help I have a sangoma A104D on my dell server; I got card status ok with no alarm If I dialed the extension 6210006, it shows the output as stated below, but there is no ringing from the pstn number nor the iax softphone am using on my pc. I will be glad if someone can give me a working config? What I want to achieve is to send all my call to the pstn on A104D? The pstn am

I've been a happy user of asterisk for over a year just for a small home setup (a Digium TDM400P with one POTS line and three internal extensions plus a couple of SIP phones). I recently moved from running Fedora Core 6 running * 1.4.1 compiled from source and zaptel 1.4.7 to Fedora 8, using the RPM package for * 1.4.18 and zaptel 1.4.9 . It worked fine for a week, but suddenly I can't

Hello all, I got a problem at an asterisk server, with dropping calls, losing all channels and reaktivating all channels and beeing back up. This problem seems to occure randomly over the whole day, when it gots traffic on the card. After looking @ google I found several hints but none did work fine. To avoid problems with the phone line (german E1) I called the provider, he did a 45 min. route

Hi, I hope someone can help me with this.... Asterisk 1.0.6 Zaptel 1.0.6 Libpri 1.0.6, 1 Digium E100P card installed Panasonic TDA200 firmware v2.0.6 E1 Card Firmware 1.0.2 System is located in Australia, so as technologies go, I believe it is twist on the euro standard for the E1 signalling. Here is the situation. The TDA E1 card is set in cross over mode and I am using a functional

Hi all, I've setup a PBX in production environment last week but we have immediatly find out drop conversations and lot of errors (in asterisk logs) like: Apr 10 17:30:48 NOTICE[25154] chan_zap.c: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 2 My configuration is: Motherboard: SuperMicro P8SCT (Intel E7221 chipset) Hypertrading and APIC enabled CPU: P4 3GHz Digium TE205P