similar to: Storing recordings

Hi, I was planning on getting a Dell PowerEdge 2950 for our new Asterisk configuration. But while searching for documentation about it and/or reported issues, I found this: http://www.voip-info.org/wiki/view/Asterisk+hardware WARNING - many Dell motherboards use the e1000 gigabit ethernet chipset, which has been known to cause random locksup - if you plan on using a Dell server, disable the

Hi all, We are running Asterisk 1.2.7.1 on our Dell Poweredge 2850 and are having massive sound quality issues. We are experiencing call quality issues for our remote location, namely calls cutting out and breaking up for our agents. The two main issues seem to be 'popping' and 'dropping' - popping would be pops and crackles on the line, where dropping would be complete audio

Hi there, I have one server acting as a iscsi target running windows storage server r2 sp2 and the other server is running centos as an initiator. They are connected to a switch over a 1Gbit ethernet connection. the target is a Dell NF600 and the server running centos is a Poweredge R900. We want to move this configuration to a FC based installation using a Dell QLE2462 HBA (this is the hba we can

I found some ancillary information that seems to indicate that there is a driver that will allow a D-Link DGE-550SX Gigabit fiber NIC to work under FreeBSD 4.x. Can anyone confirm or refute this, or provide additional information? If the NIC is not supported, is there a recommendation for a gigabit fiber NIC that works well under 4.8? Thanks, Steve

Hello All, I have one CentOS 6 KVM virtualization server that I built around a year ago (best I can tell it was in October 2012) at which time I would have been installing 6.3 [0]. That particular install used the Consistent Network Device Naming [1] conventions (PCIe NICs are p1p1, p1p2). I started to build out a new KVM virt server (kickstarting a 6.4 install now as compared to 6.3 back then)

Hi, I have installed samba on a dell poweredge server. It uses integrated NetXtreme II BCM5708 Gigabit Ethernet card. My issue is that i am getting extremely slow speeds (about 1.2MB/s) on the gigabit network from linux as well as windows clients using when reading from the samba share. On the same setup (same server, client, network) using scp,rsync,nfs gives me anything between 35-50 MB/s. So

First,sorry my poor english~ Here is this test: Virtualization performance comparison test Test environment Physical machine: Cpu 8-core 8G memory HDD: 147G xen virtual machine: cpu 2 core 4G memory 30G hard drive wmware virtual machine: cpu 2 core 4G memory 30G hard drive Optical disk array (san) Size: 7.7T Speed: 6G/sec Testing and structural I / 0 performance test Test methods Test

It's Digium, not Dell. I have two identical Dell 1850s, each with the allegedly offensive built-in E100 Ethernet ports. I placed a TE410P card in each. One worked great, the other would not modprobe. Upon examination, we discovered that the two TE410P cards had different firmware revisions. Turns out the one with the older version was the one that worked. We sent the second card back

Hello, Is there anyone who has ever done a setup of VoiceXML combined with some licenses from Nuance for the ASR/TTS engine within Asterisk ? I'm currently working with VoiceGenie, for the VoiceXML + ASR/TTS engine, but we are having a couple of issues which I guess are caused by VoiceGenie. If there's an alternative, it would be very interesting for us. Thanks, -- Eric Rousse

Hi, I have updated the firmware for perc raid controller card, network card, IDRAC firmware and the BIOS version on Dell R720 server. I have installed CentOS 6.4 and updated with all the latest packages using yum -y update. # cat /var/log/messages | grep -i error Sep 23 14:09:35 x24 kernel: ERST: Error Record Serialization Table (ERST) support is initialized. Sep 23 14:09:35 x24 kernel: ACPI

Hi, Has anyone else encounter the following; While testing the new CentOS 6.5 kernel-2.6.32-431.1.2.el6.x86_64 on a Dell PowerEdge 2950 in the lab it kernel panics on boot up, complaining about the scsi_wait_scan Module signed with unknown public key. The Dell Poweredge 2950 is running the latest 2.7.0 BIOS and BMC Firmware v2.50 with PERC5/i integrated (running latest firmware 5.2.2-0072,

Hi, I work in Dell Support and I have a customer with a PowerEdge 1650 Server with Intel? PRO/1000 XT (82544GC Gigabit Ethernet Controllers). The nic is integrated on the motherboard. The customer is using a Linux system with DHCP+tftp to PXE boot and load an MS-Dos 6.22 image, with an UNDI driver, over to the PowerEdge 1650 and then map a Samba share to install Windows 2000. The customer get

Hello, Just chiming in here: >From: asterisk-users-bounces@lists.digium.com >[mailto:asterisk-users-bounces@lists.digium.com] On >Behalf Of >bdolljr@bigskytech.com >Sent: Viernes, 22 de Julio de 2005 01:24 p.m. >To: Asterisk Users Mailing List - Non-Commercial >Discussion >Subject: RE: [Asterisk-Users] Dell Hardware >> Mmhh nice !! So, why did Digium forbid it :)?

Hello to all. I''m setting up a high capacity farm that''s going to allow many departments of a company or project have their own resources. I have little to no control over the brand of CPU (I would have much preferred AMD) and name brand of the gear, but I do get some input on what goes in each node. They are dell Power Edge 2950''s, found here :

Hi All, I've been asked to setup a 3d renderfarm at our office , at the start it will contain about 8 nodes but it should be build at growth. now the setup i had in mind is as following: All the data is already stored on a StorNext SAN filesystem (quantum ) this should be mounted on a centos server trough fiber optics , which in its turn shares the FS over NFS to all the rendernodes

Hello all, I have a PowerEdge 2950 that I am using to host Windows XP VM's under CentOS. I am experiencing poor performance in the Xen VM's. Any time I try to do something, the CPU usage (as reported by the Windows task manager) hits 100% for a few and then drops back down. This is causing the VM's to run sluggish and be quite annoying to use. Example.. I click IE.. cpu hits

Hi, I have a problem with networking under XEN, I hope someone can help me out. The problem is that after some time (a day or so) the network suddenly stops working, and it takes some waiting and/or a reboot to fix this. I''m running XEN 3.1.0-rc7 on an Intel Core2 (x86_64). It''s a Fedora 8 system, with the following packages: o Xen version 3.1.0-rc7-2950.fc8

https://bugzilla.mindrot.org/show_bug.cgi?id=1430 Summary: Restore support for "none" cipher, i.e., unencrypted connections Classification: Unclassified Product: Portable OpenSSH Version: 4.7p1 Platform: Other OS/Version: Other Status: NEW Severity: normal Priority: P2

We're having a performance issue when attempting to rsync a very large file. Transfer rate is only 1.5MB/sec. My issue looks very similar to this one: http://www.mail-archive.com/rsync at lists.samba.org/msg17812.html In that thread, a 'dynamic_hash.diff' patch was developed to work around this issue. I applied the 'dynamic_hash' patch included in the 2.6.7 src, but it

different stand alone linux server which act as my routers. Here is a picture showing the output from the CISCO switch going to the two linux servers: http://www.grmtech.com/blog/wp-content/uploads/2009/02/cisco2950-24ports-farleft-two-output-300x89.jpg My questions are: 1. The black wire coming into the Mc Manstel box is that a fibre optic cable ? 2. What is the Mc Manstel box doing ? 3. What