similar to: OT: High Quality Wireless Headset for Cisco IPPhones and *

Hi I am looking for a good wirless headset to use with the Polycom Soundpoint 501 phone. I would greatly appreciate hearing from anyone with good experiences with a specific device. Thanks -- Jim Freeze

There is no release note, just a text file that says AASTRA TELECOM INC. February 2006 FC-000046-01-07.st - 9133i Generic SIP Firmware 1.3.1.1095 for customer release. ________________________________ From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of Gareth Owen Sent: 15 February 2006 02:00 To: asterisk-users@lists.digium.com

I am looking for SIP with power over ethernet desktop phones that will work with asterisk and Plantronics HL-10 Handset Lifter for Remote Answering. Any suggestions? I am considering buying about 150 of these desktop phones for a new call center.

Hey all, after hooking up some Plantronics to some Snom's (3 320's 1 360), I noticed my client is having some form of feed back on the phone. Because of Snom's "inner oddities" this is how I got it to work. Plantronic --> RJ11 --> SnomHandset Port (on Snom Base) Handset --> Plantronic jack (bottom base in the front) If I placed Plantronic(RJ11) --> Snom's

RJ11 Plantronics 1 3 2 4 3 1 4 2 RJ11 Pin 1 is on the left when looking at the contact points. Plantronics Pin 1 is on the left when looking at the contacts (through the plastic sheild) My multimeter battery is low, so YMMV, but: Pin's 1,4 are connected with ~160 ohms Pin's 2,3 are connected with ~1400 ohms On my Plantronics head set. Chad -----Original Message----- From:

I've been asked for recommendations for a small call centre, an ethernet SIP deskphone with a wireless headset. Similar approach would be a mobile phone with bluetooth head set. Either I've not looked hard enough, or there isn't much on offer. Alec Davis -------------- next part -------------- An HTML attachment was scrubbed... URL:

I like the Plantronics CS55/HL10, it's a DECT Wireless boom headset with a lifter kit for the phone, works like a charm, great range. -Cory -----Original Message----- From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of Jim Freeze Sent: Wednesday, October 25, 2006 2:31 PM To: Asterisk Users Mailing List - Non-Commercial Discussion

On 06/05/2015 03:48 PM, John R Pierce wrote: > On 6/5/2015 1:44 PM, g wrote: >> for what it would take to do so, you are better off getting buying >> better quality at a little more cost. > > I've had pretty good luck with the basic models of Plantronics > headsets. They tend to be well made. The Logitech stuff I've > bought has often broken within a

Hi, I am investigating getting a wifi VoIP phone because its may be a better option than an ATA and a cordless phone.. Does anyone have any experience with the whats out there?? Do they support things like WPA etc?? I have heard the battery life can be a problem.. Is this the case? Thanks..

Hi all, In a legacy ''immutable'' schema I have MTI inheritance setting: <<TABLE systems>> id<<PK>> ( NOT database generated) installation_date manufacturer serial_number <<TABLE lifters>> id<<PK>><<FK>> ( NOT database generated ) max_weight drive In my model I have implemented the semantic of inheritance between

Hello! I using the latest released version (20050725). Im having problems using the parallel port. How do i setup the parallel port using the new registry system? Which modules control the parallel port. Which debug groups should i enable? /Pedro >>>> GN Netcom Group NOTICE - AUTOMATICALLY INSERTED <<<< The information transmitted is intended only

I have seen on eBay adapters for Cisco 7940/7960 phones, to use cell phone headsets. They were about 12-15$. I think original manufacturere was at http://www.ciscoheadsetadapter.com. >Started a Wiki page here: > > http://www.voip-info.org/wiki-Cisco+Phone+Headsets > > >Jim > >James H. Thompson >jht at lava.net > > ----- Original Message ----- > From:

Hi List, I am using a Plantronics CS50 head set with my Polycom 601. I use the button on it to pick up calls. Is there any way to have the phone set up that if I pick up with the button on the headset that it sends the call to the headset and that I don't have to press the headset button on the phone every time ? Thanks. Dovid -------------- next part -------------- An HTML attachment was

Does anyone have a recommendation for a headset that plugs into the Mic/Line-out port on a PC? Ideally something like the Plantronics SupraPlus. I'd prefer Monaural instead of stereo, and cheap in price but not in quality. Thanks for any suggestions... Jeremy Mann Director of IT Texas Health Management Group Direct Line: 817-310-4956 Main Line: 817-310-4999 Fax: 817-310-4990 Email: jmann at

On 6/5/2015 1:44 PM, g wrote: > for what it would take to do so, you are better off getting buying > better quality at a little more cost. I've had pretty good luck with the basic models of Plantronics headsets. They tend to be well made. The Logitech stuff I've bought has often broken within a year. -- john r pierce, recycling bits in santa cruz

Hello, I'm looking for ipPhone and ATA with UPNP and perhaps also STUN auto provisioning via https or . G729 If someone know a good product.. Thanks Laurent -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20060608/efca9a57/attachment.htm

Im having a little problem with voicemail and my cisco phones i was wondering if anyone might have seen this before and let me know whats going on. it spits this out and then my cisco ip phone reboots im using the latest cvs and a cisco 7910 phone WARNING[1234379840]: File res_adsi.c, Line 205 (__adsi_transmit_messages): Unable to send CAS -- Playing 'vm-login' (language 'en')

Hi, I'm having some problem with realtime: let's say I have a dialplan like this [globals] IPPHONES=_3XX [sip] exten=>${IPPHONES},1,Answer A call from ip phone 300 comes in, and it's been answered. Then I "switch" the sip context to realtime, putting the exten in the db and using the variable name for this as in the file version. [globals] IPPHONES=_3XX [sip]

I am able to pickup, hangup, and flash, using the buttons on the phone with all of the soft clients and both of the headsets I mentioned below. I don't believe I had to change anything on the client side, just had to get the ctp (cordless telephone profile) working in the bluetooth stack, which was a pita. I struggled with the same issue...I could use the headset, but that's not very handy

Hi, You need to have completely replaced the Microsoft driver, because it doesn't support the headset or ctp Bluetooth profiles. This gave me fits! I followed the instructions at http://www.windowsdevcenter.com/pub/a/windows/2005/07/05/bluetooth.html and it works with both a Plantronics and a Motorola Headset, and I can answer calls with idefisk, eyebeam, x-lite, and kapanga. If you end