similar to: ISDN30 and TDM400P + FAXing ...

You should be able to get ISDN though. I think BT provide this anywhere. Otherwise your solution will be a Primary rate (ISDN30) with 8 channels. -----Original Message----- From: asterisk-users-admin@lists.digium.com [mailto:asterisk-users-admin@lists.digium.com] On Behalf Of Matt Sent: 07 June 2004 10:19 To: asterisk-users@lists.digium.com Subject: Re: RE: [Asterisk-Users] Multiple DDI &

Hi, Are there any hardware for ISDN30 ? if yes any problem with this ? is i out-of-box like ISDN2 but with 30 linies ? Do I need more than the cable from my teleprowider and a PCI-card ? /HHA _________________________________________________________________ Find high-speed ‘net deals — comparison-shop your local providers here. https://broadband.msn.com

Quoth Jon Morgan <jon.morgan at motors.co.uk> > >We have a 2 port Digium TE220P card, one span is configured to connect to our ISDN30 provider (British Telecom), the other span connects to our internal PBX. Here's the zaptel.conf snip: > >span=1,1,0,ccs,hdb3,crc4 >bchan=1-15 >dchan=16 >bchan=17-31 > >span=2,0,0,ccs,hdb3,crc4 >bchan=32-46 >dchan=47

anybody recommend a supplier in the UK for a pri/isdn30 line (other than BT) thanx very much __________________________________________________ Do You Yahoo!? Tired of spam? Yahoo! Mail has the best spam protection around http://mail.yahoo.com

If anyone can help me with this I'll be soooo grateful :) We have a isdn30 line, with a DDI range. We also have 2 business units that have separate 0870 numbers that are mapped onto 2 DDI numbers. I would like to be able to present these 0870 numbers from the business units so that the correct number is displayed on a callerid, or when 1471 is dialled. BT claim that I can only have a

Hi everyone, I want to get multiple DDI's and hunting across those DDI's in case one of the lines is busy using analog phone lines. The system is for a large house so I want 3 x PSTN lines. 3 x DDI's and the ability for those DDI's to be presented across all three PSTN lines. BT say you can't have more than one DDI number associated with a PSTN line and that you can't

Hi, I've just been made aware of Asterisk through the article on Slashdot. We're a small UK company with a ISDN-30 link to the office and a Meridian (Nortel) PBX. We're expanding and moving offices soon and I'm looking seriously at VoIP technologies. So starter for ten, can Asterisk interface in with ISDN-30 technology? I'm assuming the set-up is a server sat running

Dear users. My current setup uses a euroISDN E1 with 8 cahnnels for incoming and outgoing calls from a digium te110p. Currently all phones use SIP. However, I need to add some faxes lines and some POS credit card machines. These will require POTS lines with a fixed DDI. I have purchased the tdm400p and 4 FXS modules. My problem is with the zaptel.conf and zapata.conf. I am a little confused as

Hi All, Has anyone hooked up * as an extension/trunk of an Avaya system that has around 2 ISDN30e's. Trying to add 100 extensions to one of our systems, but not sure where to start reading. Thanks. -- Kind Regards, Gavin Henry.

I'm just curious to know if anyone is using a usb 2.0 / ISDN30 (specifically EuroISDN) device. We are looking to purchase another pci card, but was wondering if anyone has any horror / success stories to share regarding a usb device. TIA Julian

Hello, I have a Sangoma A101 connected to an ISDN30 (E1 in the UK) with some Snom 300 and Idefisk softphones. I can do SIP and IAX2 calls just fine, however I cant get any audio in either direction on the Zap channels. When I call in or dial out over the ISDN30 (UK E1) I can see the call answered/placed on the CLI and then silence follows. I've been provisioned 25 out of the 31 channels only

Dear All The setup is te110p with an 8 channels PRI to make and receive all calls. SIP phones throughout the company. TDM400p with 4 FXS modules to send/receive faxes and make credit card transactions. I have an analogue phone on the tdm400p for testing. I can receive calls to the exten. There is a dialing tone. However, when I try to make a call I get a busy signal. Asterisk stated busy then

Hi :) My employer is looking to move a call centre to a new office, and has been increasingly frustrated with their legacy PBX (call-logging licensing and hardware upgrade costs). So I've stepped forth as the Open Source Pedant and suggested Asterisk so we can do all our own CallerID / call logging / analyses, and make use of IP Phones / teleworking, etc. The problem begins in that I only

On how to even search for this "feature" as I have no idea on what it can be. I've got a meridian linked to * (by EuroISDN) which is linked to a ISDN30. I can make calls from the meridian, and receive calls into the meridian. Great stuff. However, if someone dials an invalid number, then instead of hearing a "three tone", the line just drops and goes dead. The console

Hello, I'm trying to connect a Digium Wildcard TE110P T1/E1 Card to a 10 channel BT ISDN 30 box, however I'm fairly new to Asterisk and this is the first time I've set-up a telephony interface card can anyone give me some pointers or known working configurations? I'm running Asterisk 1.6 and Dahdi 2.4.1.1. Thanks, Tanuki -------------- next part -------------- An HTML attachment

My employer wants to use Asterisk, but the E1 circuit providing the current phone system is DASS2 rather than ISDN30. Converting the E1 to ISDN30 is not a practical proposition at this time as it'd stop the legacy phone system from working. Is there any sort of hardware support for DASS2? I speculate that the E100P should be able to deal with the electrical side of it, but I'm unsure of

Hi, During tests with a IAX2/PSTN gateway I've been getting strange results for processor idle time and load. I (re)search(ed) this issue for a while, but I didn't get any good explainations. Can somebody help me? I have several sites that rely on a central server for connection to the PSTN. Calls to the PSTN are routed over the Internet to this PSTN gateway using IAX2 in trunk mode. To

hi, i have problem with pass-through faxing with this scenario hylafax(iaxmodem) - iax - asterisk1 1.2.22 - sip - asterisk2 1.2.X(xen virtual) - linksys ATA i can fax to fax2mail on hylafax but after upgrade asterisk2 to 1.4 faxing is not working hylafax(iaxmodem) - iax - asterisk1 1.2.22 - sip - asterisk2 1.4.X(xen virtual) - linksys ATA configuration is same do you hava any idea what is

Dear All, Thank you for taking the time to read this post - I am *confused!* as to why my asterisk setup does not work as it should. I have an ISDN 30 connection for telephony, a Sangoma card, and asterisk installed. Incoming calls, and outgoing calls work 100%. Making an international call, results in silence, or the error message all circuits are busy Numbers being passed to the trunk for

Guys. Ive been testing how to receive faxes using TDM400P cards and so far, after playing with gains, echocancell and echotraining on zapata.conf.. Ive ha dno luck, faxes come in as garbage or broken or with blank lines. Anybody has successfully done this? Any tips.. Also I have some ideas: 1. Is it really possible to get fxes on a fax machine using ATAs like the sipura 2002? Even using ulaw