similar to: 1.4 and "sip list peers"

I am sending an email from my machine devcentos5x64. the transcript below (hangs for 60 seconds) at the line: MAIL From:<root at devcentos5x64.msgnet.com> SIZE=56 AUTH=root at devcentos5x64.msgnet.com The email succeeds - but I am trying to figure out the 60 second delay. Neither email server is busy. Nothing is waiting. the DNS on both machines point to the same nameserver. The DNS

Using asterisk 1.4 with 100M or 1000M ethernet and 230 SIP clients and a 64 bit 4200+ box would there be any noticable lag or delay to bring each one of them into a PAGE mode. so one speaker can talk out on all 230 SIP clients for a message. Would this work? Thanks, Jerry

I am trying to do an rsync or scp from machine1 to machine2. I am getting arg list to long. I am using centos 5 machine 1 and centos 4.5 on machine2. I am using the default shell which is bash. How can I get past this? THanks, Jerry

To continue here with problems on this compaq v2000 laptop, I put kernel source on a USB disk and plugged it into the v2000. NOTHING IS recognized. I tried to manually mount the disk and nothing either... I thought USB was well established.... I thought trying to recompile the kernel for realtek support might get my networking going... I am stuck??? Jerry -------------- next part

I am trying to hwclock to set the time. (hwclock -w) this is what I get on standard 5.2 x86_64. hwclock --debug hwclock from util-linux-2.13-pre7 hwclock: Open of /dev/rtc failed, errno=19: No such device. No usable clock interface found. Cannot access the Hardware Clock via any known method. [root at devcentos5x64 src]# ls -l /dev/rtc crw------- 1 root root 10, 135 Feb 6 13:32 /dev/rtc Any

hi all, running centos 4.7 i686. I seem to have an o pen r elay sendmail server. How do I close it? I have the STRAIGHT centos install sendmail.mc file. Only thing I changed was: dnl DAEMON_OPTIONS(`Port=smtp,Addr=127.0.0.1, Name=MTA')dnl so as to allow incoming email and not just localhost. however this seems to relay everyone. I looked at http://www.sendmail.org/tips/relaying but it

I am trying to plug a USB 2 device in a USB 3 slot. Nothing is being detected in "lsusb". Is there something special I need to do? I am running centos 5.5 x86_64. I thought 3.0 was backward compatible. Nothing special about my device its an RS232 to USB device. It works in 2.0 slot. Thanks, Jerry

What is needed to get DAHDI to start up correctly on CentOS 7 and systemd... I am using DAHDI-linux-complete 2.11.1 I saw mention in my search that it has been fixed after 2.11.1 but cannot find what the fix is. Thanks, Jerry -------------- next part -------------- An HTML attachment was scrubbed... URL:

I am wanting to use the mkfs.hfsplus as mentioned here http://www.oli.id.au/createosxdmgdiskimagesinlinux but I dont have the command. yum provides "*/mkfs.hfsplus" returns no packages found. Where do I find this command? Thanks. Jerry

I was just wondering if there are special tricks people do that compile A LOT on centos? Do RAM disks help or something else I dont about that minimizes your compile time? I presently have and AMD x2 4800+ with 2GIG ram. Just curious if I can reduce any more time out of my compiles. Jerry

Hi all, I have setup my Cisco 79XX phone. Did the tftp, put the config files in the right location with the right names. Booted my phone, it does the tftp things, the screen shows my extensions everything seems fine. However, when I come offhook and try to dial 11 which is just a playback of demo-congrats in the dialplan the phone says Calling Out (INV) below is my sip.conf file - I presume it

I was installing centos 5.3 x86_64 on a sempron 2.7G machine with 512M ram. The install started off fine then REALLY SLOWED down about 70% into install. I did have a swap space. after that it just crawled. I tried restart the install a couple times at 512M. Same thing around 70% the slow down. I then put in 1G of RAM and everything zipped on past and finished fine. Does 5.3 have minimum

Is there a way in asterisk to Activate/Clear the blinking light on polycom phones indicating VM. Either from an AGI or some way in the dialplan? I want to be able to control this light for from my application. I have an AGI to do something similiar to VM and want to light /clear the light myself. Thanks, Jerry

Apparently Verizon is blocking or changing packets on port 5060 so my softphone from my hotspot will not work. How do I set asterisk (11.23.0) to run default 5060 for all other devices I have - BUT for my software run on a different port like 5070? I'm using linphone and is easy to change the ports from 5060 to 5070 ( I think). Thanks, Jerry -------------- next part -------------- An HTML

Is there a cisco vpn client for linux centso 5 AMD 64 bit? Using google it talks about cisco vpn client but everyplace to download is blocked. I then found a vpnc reference but did not find a 64 bit version. yum install vpnc did nothing.... What is my next step? Jerry

I have added the three lines to the sip.conf file based on the latest changes from broadvoice. I can receive incoming calls but cannot place any outgoing calls. The error I get is: *CLI> -- Registered to '69.73.19.178', who sees us as IPADDRESS:4569 -- Attempting call on SIP/Broadvoice/5068012 for application Playback(demo-congrats) (Retry 1) Mar 8 08:35:21 NOTICE[29290]:

I have a handful of 7912's connected to my asterisk 1.2.14 server. (6 to be exact). I get the X on the display sometimes for loosing registration. I have the config file for the 7912's SipRegInterval: 60 and asterisk is the default. ; maxexpirey=3600 ;defaultexpirey=120 I've not changed them. How can I keep these phones online and stop loosing registration? Thanks, Jerry

I have a device on my network that is not DHCP and I dont know the IP address of it and it has not method of finding it or changing it unless you know the IP address (setable by browser). Is there a way on linux, based on MAC address, to get the IP of the unit? Thanks, Jerry

Is there any performance lost in using a software raid array with only 1 disk? I was wanting to use the mdadm monitoring tools to monitor the machines single disk drive for failures and such. Is there any performance hit for such a setup? Some machines have RAID some machines dont (for me) and I was thinking about a common setup. Also then if I want in the future I can actually just add the

I am getting an error about to many open files. I tried to "echo 500000 > /proc/sys/fs/file-max" The number is there now, but I continue to get the error. Is there something else to do? Jerry