similar to: Dropped calls

Hi, all My Asterisk uses a Digium TE120Pand I would like to add an Astribank zaptel_hardware sees is, but I cannot get it working pbx:~# zaptel_hardware Argument "IRQ" isn't numeric in numeric comparison (<=>) at /usr/local/share/perl/5.8.8/Zaptel/Span.pm line 114. usb:005/002 xpp_usb- e4e4:1131 Astribank-8/16 USB-firmware pci:0000:04:00.0 wcte12xp+

I have recently updated from Centos/*1.2 to Ubuntu Server and FreePBX 2.8.0.2. We have an Astribank with 4 T1 ports and 16 FXS ports. After updating, we had it working for a while with one NT PRI and one TE PRI and, in the process of trying to configure another PRI, I ran into a couple problems. (1) As my configuration changes didn't seem to affect the Astribank, I power-cycled it. I

H all... I have an Astribank (8FXS/16FXO), IBM X3200 M2, Asterisk-1.6.2.1, dahdi-linux-complete-2.2.1, libpri-1.4.10.2, centos-5.4 final. My problem is, every time i unplug the astribank power supply, and reconnect it, astribank cannot work again (lsusb result is 11x0)... but, after reinstall the asterisk and dahdi, astribank will detected (lsusb result is 11x2)... any suggestion? Regard,

Hi Guys, An 8 channel Astribank is connected to Trixbox 2.8 and I ran freepbx-module-zapauto but I get the following when running these commands and can't make calls out: [Trixbox]# dahdi_genconf xpporder /usr/sbin/dahdi_genconf: warning - OLD DRIVER: missing '/sys/bus/xpds/devices/00:0:0/timing_priority'. Fall back to /proc pbx*CLI> dahdi show channels Chan Extension Context

Hello, I'm in the process of building an Asterisk machine and need 5 or 6 BRI-Channels. I was looking for the beroNet and Junghans cards and stumbled upon the Xorcom Astribank xBRI products. Has anybody tried out the Astribank xBRI-Channel Banks? Are they production ready or should I go with a beroNet BN8S0 or JUNGHANNS.NET octoBRI ISDN? Thanks in advance, Lars -- We don't like their

Hello, I am trying to update to dahdi 2.2.1. But somehow the xorcom (2BRI) device does not want to work. I pasted below the information I have. pbx at loicvoip1:~# /usr/share/dahdi/xpp_fxloader reset pbx at loicvoip1:~# /usr/share/dahdi/xpp_fxloader usb 'xpp_fxloader'[4937]: --------- FIRMWARE LOADING: (usb) [1 devices] ..Got all 1 devices 'xpp_fxloader'[5003]: ---------

My equipement : 2x tdm 400p /4FXO/4FXS 16 PORT ASTRIBANK My first TDM400p is the sync master, so i set astribank to sync to it, but the quality is bad, like it is going fine and second after >>ROBOVOICE ;) any other devices (isdn/sip/tdm cards) are working fine, looks like astribank dont like to be sync 'slave'. Is there any way to change sync master manually, so every another

I have a customer running Asterisk 1.2.13 with Zaptel 1.2.11 that is having calls dropped. Sometimes you can stay on the phone for a long time and sometimes the call is dropped within a minute. There are 9 lines connected to 3 TDM04B cards. The Panasonic Pbx we replaced did not have this problem. There are 8 SIP phones and 16 analog phones connected to two Astribank-8 units and everyone

Hello, I've one astribank with 8 FXO unit and 8 pstn lines connected to the astribank. When I receive calls on my ipphone I get always Unknown callerid. It's is possible to receive the callerid from the lines on the astribank unit? This is my config: [channels] language=es context=from-zaptel signalling=fxs_ks ;rxwink=300 usecallerid=yes callerid=asreceived ;cidsignalling=bell

Hi All Just a quick check on the best way to ensure multiple cards/devices load in the correct order. Asterisk 1.8 with Sangoma A101 had no problems until we introduced an Astribank. root at pabx377:/etc/asterisk# dahdi_hardware -v usb:001/004 xpp_usb+ e4e4:1162 Astribank-modular FPGA-firmware LABEL=[usb:X1060395] CONNECTOR=@usb-0000:00:1d.7-3 XBUS-00/XPD-00:

Hi, I am looking to connect 66 analog phones to an asterisk box. I was thinking of a Xorcom astribank 32port (2 of them and another 8 port). this is because the phones have no near connection to an ip network, so replacing the phones in favor of voip phones+network cabling is kinda out of the question. In your experience, will these units support all the phones talking at the same time with

Hi, all I want to configure a few FXS ports in an Antribank-16 to be able to receive faxes sent throught a PRI: E1 ==>Zap * ==>FXS * ==>Fax machine My asterisk box has a Digium TE120P (for the PRI). Versions are *=> 1.4.17 | Zaptel=>1.4.8 | libpri=>1.4.5 The Astribank is not configured yet, because I am a little bit confused about how to do it. Let's say I configure

Hello Mailinglist, we have a Xorcom Astribank which is installed at our client and working since 10/2008. Suddenly last week there where odd behaviors, no calls going through (it is used to route calls to GSM Gateways). Upon testing (reinitialization of the complete gear) it turned out that one call get's through and then nothing more. I have nothing in the logs, indicating that Asterisk

I get the following error when trying to compile zaptel on CentOS 5 kernel 2.6.18-8.1.3.el5 CC [M] /root/asterisk-src/zaptel-1.2.17.1/xpp/xbus-core.o /root/asterisk-src/zaptel-1.2.17.1/xpp/xbus-core.c: In function ? /root/asterisk-src/zaptel-1.2.17.1/xpp/xbus-core.c:171: error: ? has no member named ? make[3]: *** [/root/asterisk-src/zaptel-1.2.17.1/xpp/xbus-core.o] Error 1 make[2]: ***

I'm having trouble getting a xorcom set up. A large part of the problem is that the box is a _long_ way away and I can't get to/at it easily, so while I could probably fix this in a few hours if the machine were in front of me, I'm struggling over a slow unreliable laggy link. Ok, enough whining from me. I have a new Xorcom plugged into the usb of a Suse 11 machine I built Dahdi

Hi All I've got an asterisk system, using a couple of Xorcom Astribanks to provide FXS ports. (I'm using the zaptel 1.2 branch, if that matters) I've noticed that the ringing volume is a lot louder than on our old phone system, and people are starting to complain it's too loud. (This is the noise the phone makes when it rings, not the noise in your handset when you ring

I have a customer running Asterisk 1.2.13, Zaptel 1.2.11 with a TE110P, a TDM04B and an Astribank-32. They have been complaining that there is echo on calls even when they are IP to IP on the same network. There are 18 Aastra 9133i phones and 30 analog phones connected to the Astribank. I can understand there being a bit of echo on the analog phones, but I do not understand why there would be

I have a server with 8 Xorcom Astribank, they're connected to the server via a USB hub, my problem is: when a reboot the server the ID of the Channel Bank changes, cousing a big mess on my server. Anybody know how can I solve this ? Best regards, -- Guilherme Loch G?es Visite nossa loja virtual: http://www.shopvoip.com.br Not?cias e F?rum sobre VoIP com software livre:

Hi, I have upgraded an Asterisk installation with a Xorcom BRI Astribank that was working under Ubuntu 8.04 to Ubuntu 9.10 and the device is no longer initialized. When I reload the udev rules, I see that the rules seems to be correctly loaded: udevd[452]: reading '/etc/udev/rules.d/40-xpp.rules' as rules file However, these rules do not seem to be triggered: # udevadm trigger

Hi all, I'm interested in buy a Astribank-32 but i never heard about detection of far-end disconnection. Does anyone have some experience about that functionality in this hardware ? Thanks in Advance, Gleidson Antonio Henriques