similar to: dundi ENCREJ

>Searching for 'vorbis' to find the packet boundary is wrong however. >The lacing values in the Ogg page header tells you exactly where the >division is. OK, so given the fact that a page can also contain multiple packets this means that the lacing values of one page could be like the following example: 255 255 189 (something less than 255, indicating that a new packet starts

Well, I've been dicking around with DUNDi for about 4 hours now. I have two systems that I am trying to get to peer with each other. Queries are working one way, but not the other. The server, pbx1, that is refusing to deliver any queries and logs what's below to the console. Why??? I've checked all the config files more times than I can remember. The 'RFC' for DUNDi at

hello, I have a problem with an unsuitable font in the windows menus/dialogs with the above versions of wine (dont think this depends much on the versions, though. Have not tried other versions so far.) when using debian sarge. The font seems to look a bit ugly, usually destroys partly the menu/dialog structures, and, most important, has no German umlaut's (the diphtongs ae, oe, ue and

Hello all, my name is Mathias, I'd like to ask about some details of the OGG format because I'm quite new to it. I'd like to write a native .NET library for reading and writing Vorbis comments. It's going to be open-sourced as soon as it's finished. So here it goes: 1) When packing (Vorbis) packets to OGG pages, does a new packet always begin on a fresh OGG page? Within the

Hello, I'm Rene living in Germany. I have a problem when I use syslinux versions greater than 3.xx for booting DOS (over dos.bss) and DSL-linux from a hard disk. (I've tried version 3.11 and the newest 3.36). The problem occurred after booting DOS - I can not access to the ordinary 3.5'-floppy drive (e.g. the command "dir a:" fails after a while). DOS not even notices

Hi All, I've been banging my head on a small dundi problem... I have two * servers setup, both have almost identical dundi.conf files: root@tsjonge:/opt/asterisk/etc# cat dundi.conf [general] department=thuis organization=pipsworld locality=Amsterdam stateprov=NH country=NL email=remco@pipsworld.nl phone=+31207508308 ;bindaddr=0.0.0.0 ;port=4520 entity=00:02:b3:49:69:5e ttl=16

Hi there, my name is Sebastian Dziallas and I would like to contribute to the CentOS Wiki. I thought a bit about what I could do and I think I would like to help translating the wiki in other languages. I speak English, German and also French. My UserName is - what a surprise - SebastianDziallas. On the HowToContribute-Page you said that I should know where to put the articles. As you

Hi there Managed to get Xen up and running, also to get a 1394 controller to be hidden from dom0 to domU. I run an lvm in raid5 in domU as a fileserver. when I copy data to the raid, I get *hundreds* of these error messages: (XEN) APIC error on CPU0: 02(02) my system is: PC-Chips 848A with AMD Geode NX1750 2 G Ram Raid 1 with md0 that holds Dom0 Raid 1 with md1, that holds lvm for domUs All

Hello Versions 10,11,12 and X3 aren't working yet. The only one who works (nearly clean) is Version 9. But you need some additional native dlls and wine until version 0.9.22. Version 0.9.23 - 25 have a strong regression. Roland ----- Urspr?ngliche Mail ---- Von: "news@swwwk.com" <news@swwwk.com> An: wine-users@winehq.org Gesendet: Dienstag, den 14. November 2006, 07:15:16

>That would be great! We always need help improving our documentation. OK. I'm going to start writing this lib now, and as soon as it works well I'm going to write specs about how to tag vorbis files. I'll let you know then. Maybe I have to ask you some further questions during development. Let's see. Thank you so far, Mathias

Hello, I got a Problem with my HFC Card, I start my "asterisk -vvvvvvvvvvvvc" The console comes up: ---------------snip---------- Asterisk Ready. *CLI> ---------------snip---------- Setting up debuglevel for span 1 ---------------snip---------- *CLI> pri intense debug span 1 Enabled EXTENSIVE debugging on span 1 ---------------snip---------- Console output:

OK, I've found the answer for one of my previous question myself in the meantime. The comment header can of course be split over more than 1 ogg page since the comment header can be greater than 64K. It also seems to be possible that both comment AND setup headers are placed on a single ogg page only (as stated in the Voribs specs). Due to the fact that the first audio packet also begins on

Ralph, thanks for your help. >>Since the length of the precedent identification header is fixed, this even is a fixed offset >>into the logical ogg stream. >This will work for all the vorbis-only files I've seen (because no one >pads the first packet). You should really implement a proper ogg parser, >but by all means get a hack working first. I will of course use the

Hi ! Playing yetisports 1,2,4 and 5 works with cvs version of wine- Starting yetisports 8,7,6 and 3 fails: yetisports 8 -------------- wine: Unhandled page fault on read access to 0x02af1d74 at address 0x0000:0x00403f0e (thread 0009), starting debugger... WineDbg starting on pid 0x8 First chance exception: page fault on read access to 0x02af1d74 in 32-bit code (0x00403f0e). Register dump:

Thanks for your replys. >packets don't always begin at the >start of a page OK, since I only want to read / write the Vorbis comments, I can limit it to the Vorbis header packets. http://xiph.org/vorbis/doc/Vorbis_I_spec.html stats that the comment header always begins on the second ogg page. Since the length of the precedent identification header is fixed, this even is a fixed offset

Hello, I try to run an windows application with wine the first time, read faqs and howtos, but I do not have a clue where to find a solution for my problem. Maybe you can give me a hint. I installed the windows application "SchildNRW" with jochen@rod:~$ wine .wine/drive_c/SchildBasisSetup.exe That was all right. ( Invoking /usr/lib/wine/wine.bin .wine/drive_c/SchildBasisSetup.exe

Hello together! I've found a couple of bugs with current compiz git, most of them related to the use of KDE and wanted to let you know. 1. kde-window-decorator crashes every now and then. This seems to be especially often when starting kaffeine media player, but not exclusively. I've attached a backtrace, though I don't know if it is useful in this form... 2. Resizing a

hi list, after connecting 3 asterisk servers via IAX in a line (+ 1 client at each end), i noticed that call path optimization happens only one time, i.e. only one node/leg in the path can be reduced. Does anybody know if this is the intended behaviour or if it's a bug? Can anyone confirm my observations? It seems that the first node, that sends the TXREQ Message, is "optimized".