similar to: Digium Wildcard B410P

Network Configurations Block D, Surrey Park, Barham Road, Westville, 3610 Helpdesk: (086) 163-8266 Tel: (031) 266-1563 Fax: (031) 266-4206 Hi list. Has anyone used any commercial or open source application to integrate Asterisk into MS Outlook 2003 which can be used to place calls directly to contacts from Outlook? And if so how well does it work? Thanks, Richard Best Regards Richard

Network Configurations Block D, Surrey Park, Barham Road, Westville, 3610 Helpdesk: (086) 163-8266 Tel: (031) 266-1563 Fax: (031) 266-4206 Hi List. I'm in need of something that will allow me to analyze cdr details either via .csv or mysql that will give me call durations as well as call costs. This is so that we can see in what areas/staff are costing what per month/week on outbound

This is my problem. I don't even know it this is the right site to ask for it, but let's go. I've a Asterisk box with 1.4.1 version version installed. It's equipped with a TDM400 with 2 FXO modules and a HFC based ISDN BRI card. Everything goes OK, except for the following scenario: on the PMP S0 bus of the ISDN telecom NT adapter I've connected both a ISDN modem and the HFC

Hi. Has anyone had any success in implementing a callback or ringback function in Asterisk? I've had a look at the callback-voicemail example on voip-info.org http://www.voip-info.org/wiki/view/Asterisk+tips+callback However it won't quite work for me. I need it for local SIP users which most of them don't have voicemail. If one SIP user calls another SIP user and the second user is

Hello, Junghanns and BeroNet offer 8 BRI ports cards. Do you know if Digium's B410P has an inner TDM bus so that an 8 BRI ports subsystem (2 PCI slots used, but 1 one set of interrupts) could be made out of 2 B410P ? I know you could (theorically) do this with Junghanns and BeroNet cards. Cheers -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi list, we have a dual Xeon server with 2GB RAM running Debian Etch 2.6.18.4-686 kernel. The server has 2 B410P cards plugged in. No other card. We installed Asterisk 1.4 trunk with zaptel trunk, ran make b410p, the install mISDN1.1.0 (for bug 9064) configure and compile Asterisk with chan_misdn, all is fine. In misdn-init.conf we have added option=1,master_clock. Asterisk is up and

Hi all! Sorry for my poor english, i'm italian. I installed Digium B410P on my asterisk server. I followed the official installation instructions found on digium site. These instruction, in my opinion, are not clear, so i tried with other ways (found on the trixbox site). I found this: http://www.trixbox.org/forums/trixbox-forums/trunks/howto-install-script-digium-b410p Now i can receive

Hi, Which echo-canceler shall I pick for Digium B410P ? Is HPEC relevant ? Reading from its datasheet, it seems related to analog cards. Regards -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20080221/ed5c5d6f/attachment.htm

Hi, Until now I've been using my Digium B410P cards with misdn 1.0.x. I would like to upgrade my systems and am now wondering which is the "best" route to take: - use the latest release of misdn v1 - upgrade to the latest "stable" kernel and use the built-in misdn v2 - use misdn v2 as a seperate package (disable misdn in the kernel) - use dahdi's support for misdn

Network Configurations Block D, Surrey Park, Barham Road, Westville, 3610 Helpdesk: (086) 163-8266 Tel: (031) 266-1563 Fax: (031) 266-4206 Hi people. I'm hoping someone has come across this problem with version 1.2.14 In my dial plan I call various SIP phones using the following little macro: exten => s,1,Set(TIMEOUT(absolute)=14400) exten =>

Hi, My set up is : Asterisk with B410P in NT mode <-------------cat5 straight cable ----------------> Another PBX in TE mode Is the 100 Ohm terminator you can find on B410P boards, necessary when connecting in NT mode to another PBX (set in TE mode) ? Cheers -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi, Is it possible to both use Digium B410P and bristuff'ed 1.4 Asterisk, now ? I've heard BRI support in Asterisk is about to change with 1.6 but I'm not sure I understood what the plan is. If someone has a clue, l would delighted to learn about it. Cheers -------------- next part -------------- An HTML attachment was scrubbed... URL:

We have recently purchased a B410P Digium 4* ISDN-2 card with hardware EC. On the same server, I also have a regular Digium 4-channel PSTN-card (TDM410P ?), used to interface to some analog devices, a.o. 2 fax machines. For faxing, EC needs to be off (or so I understand from the archives). How can I switch EC off for an ISDN B-channel if a fax is coming in? Z.

Hi all, I am having trouble setting the signalling method for the B410P using DAHDI. Asterisk complains that it has never heard of 'bri_cpe' or 'bri_net' - but it doesn't mind having 'pri_cpe' etc. ERROR[4294]: chan_dahdi.c:11327 process_dahdi: Unknown signalling method 'bri_net' Dahdi - dahdi-linux-complete-2.1.0.4+2.1.0.2 Asterisk - 1.4.23.1 Libpri - 1.4.9

The DAHDI docs actually include the 'steps' that used to be in Zaptel's 'make b410p'. These steps involve downloading and compiling mISDN. Why re-invent the wheel? Just a thought :-). As for the 100ohm termination bit - it's simply changing a couple of dip switches on the b410p card (as described in the manual). Andy -----Original Message----- From:

Hi, I've read that the new dahdi channel supporting B410P doesn't support PtmP when in NT mode. Does it support PtmP when in TE mode ? Cheers -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20081209/f422b5d0/attachment.htm

Hello, Is it possible, for testing, to connect an cat5 straight patch cord between 2 ports of a Digium B410P card and use these 2 ports as a normal dahdi trunk ? I've tried this: One port is set as NT, the other as TE. I would expect timing to come for system hardware so I choose in /etc/dahdi/system.conf : span=1,0,0,ccs,ami span=2,0,0,ccs,ami Results: - both ports lights are green -

Hi, 1. Has someone met any success at all, connecting a Digium B410P to a Patton Smartnode 4638 (with latest 5.3 firmware) ? 2. If positive, then, which signalling was used on both sides ? My project's goal is use a Patton Smartnode 4638 to act as telco BRI lines, from a B410P-enabled asterisk box. In my testings, I can see channel is respectively up (with patton web server status page)

Hi. Using Asterisk 1.4.13 running on Ubuntu 7.04 with Intel CPU: 1) Not being able to build mISDN on Ubuntu using "make b410p" I have used mISDN-1_1_7 which seems to work ok. QUESTION: Should I expect this version of mISDN to work ok with these cards? Or is there a way to build using "make b410P" on Ubuntu? (make force does not help at all) 2) In some of our installations

Hello all, I'm trying to conect two asterisk servers using two B410p Digium cards. One card on each server. I just setting up the first BRI port on server A as nt_ptp and the first BRI port on server B as te_ptp. I use an ethernet wire to connect the first port of server A (nt_ptp) with the first port on server B (te_ptp) but the port light cotinues blinking on red on both sides once the