similar to: Connect many fax lines?

Sorry if I post in this forum, this may be not the right one, but I hope to find in here some experts which could help me out. I have in one location 8 extensions from a Panasonic PBX ?KX-TD1232? connected to FXO Ports on an MultiVoIP Gateway from Multitech. On the other location I have 8 SP5100 IP-Phones from Micronet as remote extensions. Between the locations I have a VPN.

In the mailing list archives, I found a message that indicates that the IAXy has the ulaw, alaw, and g726 codecs, but I cannot find anything official on Digium's site about it. The Installation Manual has an example iax.conf file that indicates the ulaw codec, so I know that one is good. But we are thinking about using the IAXy over a VPN, to replace our MultiVoip. alaw and ulaw are

Greetings list, I've been asked to provide a system for 200 extensions, most of which will be existing analogue POTS handsets, not IP handsets. I've not really had any experience with large channel banks in the past (since most of our deployments are strictly IP-only to the desk), so I'm at a loss as to which ones are worth looking at. If anyone's had experience using channel

Hi, Can anybody with previous experience with it guide me on how to setup asterisk with analog e&m to connect it to an old style e&m system which uses 4 pair cables on RJ 45 jacks. All the analog cards I know of use RJ 11 jacks. And there is no choice of modernization of the customer equipment. Cable pin out are as follows: 1. M lead 2. E lead 3. Tip1 4. Ring 5. Tip 6. Ring1 7. SG 8.

Hi, I have one in stock - got it from a client who wanted to get rid of all his old IT equipment. Looks strange, did not have enough time to play with it ....Tried it once, looked hard to configure. It stays unused in the storage room. Peter On 29.4.2010 10:20, Tim Nelson wrote: > Greetings all- > > I've stumbled upon a TDMoE gateway for FXO/FXS called the SpiderMux. It looks

Greetings all- I've stumbled upon a TDMoE gateway for FXO/FXS called the SpiderMux. It looks rather interesting. Has anyone used one? Where did you purchase it? Pricing? Operational issues? http://spidermux.com/ Tim Nelson Systems/Network Support Rockbochs Inc. (218)727-4332 x105

I've been working with the old-style (pre-SIP) MultiTech MultiVOIPs, trying to make them work against chan_h323. With the voips in rfc2833 mode, Asterisk can detect DTMF fine from them, but when it sends DTMF to them, they lock up on the second digit, crying about an incoming fax. Has anyone encountered that problem (and found a solution)? Taking the other route, switching DTMF to inband on

Anyone know what the POE draw is for the Aastra 480i phones? We have switches that will do 15 watts on 12 ports but only do 7.7 watts on all 24 ports. A Cisco 3560 switch will do 15.6 watts on all 24 ports. Just trying to find out if we need that much power. Can't seem to find any info on the Aastra site. Comments?

I need to setup HylaFax which leads to my first question, anyone got an opinion on whether or not to use HylaFax or HylaFax+? Also, I have to setup a Digi serial port server for an external fax modem. Any reco''s on a robust unit that won''t need to be reset often? Thanks! jlc

Last week I was able to do some debugging of the problem I'm having with IAX2/GSM, residential-grade broadband, and VOIP. To summarize, I am having a great learning experience with * and Zap cards, SIP and IAX2. I hit a wall though, when I registered with iaxtel and tried doing VOIP. I spend the better part of a workday with the jitterbuffer and all sorts of settings and finally started to

I have a cisco 7910 phone, I'm trying to get it to connect to asterisk, But it seems like it needs either a SEPDefault.cnf file or a SEPMACADDR.cnf file to Continue, I created empty ones but it's still sitting there saying "opening" Does anyone have examples of the SEPDefault.cnf file? Kevin,

Hello everybody. First of all thanks to all the people giving their opinion on the subject I proposed: "Trixbox vs. custom install". You've all been very helpful. I try to summarize what has emerged from the various messages. Forgive me if I miss or forget something or if I simplify too much some of your messages... - Elman Efendiyev says that you should install from sources if

Anyone has configued Multivoip 3010 with Asterisk ? I am tring to configure this box to work with asterisk . Thanks Imthiyaz -------------------------------------------------------------------- mail2web - Check your email from the web at http://mail2web.com/ .

Hello All, I have a request from a prospectieve client to deploy a PBX capacity that can do up to 3000+ lines within a geographic region similar to a campus. The client wants analog lines for extensions and maybe VoIP for some backhaul traffic while the other traffic would be carrid via E1 channels. The client has other proposals to buy a mid, range telco switch from alcatel or simens but i am

Colleagues, We're in the process of standardizing on Sprint PCS and Cingular phones on a national basis (~ 50 properties, 1000's of lines). I manage an Asterisk install at one location. I've been looking at the Multitech CellFinder CDMA for Sprint as a dial backup solution. Basically, it's a CDMA to POTS gateway, tied to a PCS account. We would see it as a trunk line and I

I've been replacing an old Toshiba DK switch with an Asterisk solution. I'm needing a solution for fax machines that works as well as a POTS line from my carrier. If the POTS line is the solution, I'll keep it, but I'd rather move away from that. Here's what I'm thinking...will it work? I would use a dual-port Digium T1 card. In one port, I'd terminate a telco PRI

We recently had a customer install that went horribly wrong. Serious echo (pots lines into a cac cb) that, although * did a good job getting rid of alot of it, could not get rid of it all. We tried everything, every canceller, gain setting, etc... combination possible to no avail. Both the vegastream and mediatrix boxes also could not get rid of all of the echo. So, on an off chance, we

Hi List, I have a Multitech H323 Gateway MVP400 box with 1 phone on port FXO 1. I have Asterisk ruuning in Fedora Core 3. Both are in the same network. But I can't figure what I have to do in Asterisk to make that box work. What files I have to configure? Can anyone help me? I will really appreaciate youu help. Luis. _________________________________________________________ Do You Yahoo!?

Is the Sipura 3000 the only way to interface a remote pstn line and connect incoming calls to Asterisk? I have a location connected by network that has a phone line, when the room is occupied I want the line ti ring there as normal, but when the employee is travelling I want the line to be conencted to a ATA that then feeds it as an incoming pstn line to the pbx located at my office so it can

It's been many years, but it seems that I have to receive a fax and might have to send one too. Is there a way to do this on CentOS 5.5? (Hope so.) tia. -- Anything is easy if you know how to do it.