Displaying 20 results from an estimated 20000 matches similar to: "bridging isdn calls to free up channels"
2013 Aug 27
1
ISDN outgoing caller id
Hi,
is anybody out there who can set the outgoing caller id on ISDN (CAPI
or misdn) channels? I've tryed everything what I found in forums, os
voip-info.com but no luck. I use a fritz card with CAPI in my first
installation (1 BRI), and a hfc 4 port bri card with misdn on other.
The first installation have p-t-mp configuration, the second one is
p-t-p. Both configuration is EuroISDN in
2008 Oct 30
1
ISDN - BRI
Subsequent to some previous E-Mails, I've been trying to dig into the ISDN - BRI situation a bit more. I have determined that I have a HFC card with Winbond chip, but I'm not sure what combination of drivers is best or usable.
zaphfc is out because it only supports the cologne chip.
misdn is a possibility. I haven't determined if it supports the card natively, or needs a card
2009 Mar 12
2
BRI/ISDN, misdn.conf/misdn-init.conf, OpenVOX B100P and Etisalat in Dubai
Hi All,
We've got msidn configured:
Port 1: TE-mode BRI S/T interface line (for phone lines)
-> Protocol: DSS1 (Euro ISDN)
-> childcnt: 2
--------
mISDN_close: fid(3) isize(131072) inbuf(0x8fd5060) irp(0x8fd5060)
iend(0x8fd5060)
and running on Asterisk 1.4.21.2:
pbx*CLI> misdn show stacks
BEGIN STACK_LIST:
* Port 1 Type TE Prot. PMP L2Link UP L1Link:UP Blocked:0 Debug:0
2006 Oct 18
2
echotraining=yes in misdn.conf is invalid or out of range.
Hi.
I'm having problems with chan_mISDN configuration. Line
"echotraining=yes" causes warning, when Asterisk is parsing misdn.conf
and I'm confused why the PBX doesn't accept the setting. No matter
which section I try to offer it, it is always invalid or out of range.
The setting itself is supposed to be valid, it is in the sample
configuration file of chan_mISDN 0.3.1.
2009 Jan 24
1
Which policy for ISDN BRI support in NT/PtMP ?
Hi,
As you may know, these ISDN BRI features are very important here in Europe
as ISDN Basic Rate Access is very popular among Small & Medium Entreprises.
I don't really know why but it seems that in many countries, default is to
install small PBX using Point-to-Multipoint (PtMP) mode as opposed to
Point-to-Point (PtP) which is the norm for PRI.
So basically, in several countries, SME
2004 Oct 20
2
chan_mISDN problem
I'm using avm fritz card usb with kernel 2.6 patch with mISDN. The module is load correctly when I type lsmod I've got the following output:
Module Size Used by
zaptel 178308 0
avmfritz 21388 0
mISDN_isac 14336 1 avmfritz
mISDN_dsp 191424 0
l3udss1 34184 0
mISDN_l2 39040 0
2006 Jun 17
3
ISDN BRI NetJet
I'm trying to use a Teles (netjet) ISDN BRI card with asterisk 1.2.9.1
Anyone was able to use this card with asterisk? I couldn't find much
information about it. Any help?
2009 Jan 13
3
mISDN BRI Asterisk 1.4
Good Evening,
The company I work for is attempting to connect an Cisco ISDN Router to an OpenVOX B200P BRI Card so that we can get it to dial out across an existing ISDN PRI Line also installed in the Asterisk PBX
Everything has compiled successfully and the BRI card has been detected when mISDN is started:
# misdnportinfo
Port 1: NT-mode BRI S/T interface port (for phones)
-> Interface
2005 Jan 30
3
Callgroup with bristuff ISDN?
Hi list!
I'm still trying to figure out about the groups in asterisk.
If I understand correctly, if you assign a certain group number and you
assign the same call group number to a sip device the device will reing
even though you did not specifically specify it in extension.conf?
How will this work for ISDN BRI/PRI?
I don't want some extensions to get all calls from the BRI/PRI, just
2004 Jun 30
6
zaphfc - hfc pci based ISDN card : point2point & DDI
hello,
anyone has worknig ISDN hfc-pci card in DDI (DID) point2point mode?
what kernel ?
and second question mISDN driver .. anyone has working solution with
mISDN and maybe fritz card?
what you suggest for DDI -> point2point mode (card,kernel,chan_..., ...) ?
thank you,
Tomaz
2011 May 23
3
Latest DAHDI/libpri/Asterisk 1.8 & 1x BRI port HFC based ISDN card?
Hi,
I would appreciate some advice on the following: how does one use a
single BRI port HFC chipset based ISDN cards with the latest DAHDI,
libpri and Asterisk 1.8?
For Asterisk 1.4 I would first install mISDN & mISDNuser and then build
Asterisk 1.4. Now I noticed that Digium's HFC chipset based B410P is
supported by the latest DAHDI & libpri but reading the source of the
2009 Oct 24
3
OT - mISDN and B410P questions
Hello,
I'm evaluating to possibility to use chan_misdn as a short term workaround,
in case latest Dahdi is not stable enough for what we are planning to do (we
wish to use Junghanns and Digium BRI hardware with Asterisk 1.6) .
I've read www.mISDN.org but still have a couple of questions :
1. Is correct that in a 2.6.27 (and up) enabled kernel, the "embedded" mISDN
version is
2010 Sep 28
3
ISDN - Busy signal on 3rd call
Hello,
Following my first mail about this issue [1], I think I know now what
the problem is.
When I have both lines being used and a third call comes in, the person
calling doesn't get a busy tone, he gets something like line unavailable.
I've been debugging mISDN and I think the reason is because asterisk is
sending the release cause as 0.
P[ 3] --> channel:0 mode:TE cause:0
2009 Feb 06
1
set caller id on outgoing calls through BRIISDNlines
You're quite right. We'll need to see your misdn.conf file to check the
settings.
-->> -----Original Message-----
-->> From: asterisk-users-bounces at lists.digium.com
[mailto:asterisk-users-
-->> bounces at lists.digium.com] On Behalf Of Vieri
-->> Sent: 06 February 2009 13:49
-->> To: asterisk-users at lists.digium.com
-->> Subject:
2008 Jan 12
1
ISDN channels not properly released after call
Hello everyone,
I'm using very simple setup to make and receive external ISDN calls through a
softphone (x-lite version 3.0 - Win32) via an asterisk box.
Hardware setup:
- Dialogic Diva BRI (lspci yields: Network controller: Eicon
Technology Corporation DIVA Server BRI-2M/-2F (rev 01))
- ISDN BRI line
Software setup:
- Redhat 9
- asterisk-1.4.16.2
- chan_capi-1.0.2
Asterisk configuration
2015 May 26
2
Seeking advice about ISDN BRI Cards
Checkout Beronet ISDN cards and Berofix Gateway (appliance or pci card)
Personally for my last installation I chose Berofix card which is rock
solid and reliable, yet easily configurable.
With berofix you don't need telephony drivers on the host system, the isdn
card is detected as a NIC and all configuration is done using a web
interface.
Then you configure FreePBX a new trunk to use the
2005 Sep 19
0
ISDN BRI 2 pci cards and mISDN
<!DOCTYPE html PUBLIC "-//W3C//DTD HTML 4.01 Transitional//EN">
<html>
<head>
<meta http-equiv="Content-Type" content="text/html;charset=utf-8">
<title></title>
</head>
<body>
<br>
<!--+GtkHTML:<DATA class="ClueFlow" key="orig" value="0">--> I connected
my * box to two
2009 Feb 06
1
set caller id on outgoing calls through BRI ISDNlines
Use Set(CALLERID(num)=9999999999) instead of using CALLERID(all).
Remember to set this BEFORE you Dial.
-->> -----Original Message-----
-->> From: asterisk-users-bounces at lists.digium.com
[mailto:asterisk-users-
-->> bounces at lists.digium.com] On Behalf Of Vieri
-->> Sent: 06 February 2009 12:36
-->> To: asterisk-users at lists.digium.com
-->>
2004 Nov 20
2
zaphfc sound problems
hi list.
after my unsuccessfull experiences with mISDN i tried again to implement
a zaphfc based solution.
problem is: sound on calls via capi is stuttering/broken and therefore
unuseable.
my conf:
- cel 1300, 256mb ram
- avm b1 via capi connected to my outgoing ISDN
- acer surf pci via zaphafc and crosslink cable with termination as
internal bus
- siemens gigaset 3035 as internal phone
-
2005 Feb 11
2
chan_capi or chan_mISDN vs bristuff
Hi list!
I'm currently using a HFC-S card for my ISDN BRI line with bristuff. The
instability is driving me crazy however.
I'm having continuous problems where inbound calls will not work after
some time of operation (the number then appears as not in use to the
caller) or also outbound calls do not work.
The solution is to unload the modules, stop asterisk, re-load the modules
and