similar to: Asterisk Sends 180-RINGING to UA even with progressinband=yes

Andrew, I don't think it's a Polycom issue. We took Asterisk out of the picture and had our Polycom phones communicate directly with an Audiocodes PSTN gateway. Unlike Asterisk, the audiocodes do not send 180 Ringing before sending 183 Session Progress, and the polycom's play the correct tones in this case. We WANT Asterisk to send progress tones in band. In our case it IS needed.

Any ideas on why callers who call into my customer's SIP trunk are not hearing a ringback tone? I had this on one other asterisk system, and wound up needing to set progressinband=yes in the SIP trunk config. I have set this on the current system & restarted asterisk, but to no avail. I am using: AsteriskNOW distro Asterisk build is 1.6 from AsteriskNOW repository:

I don't expect my SIP provider to provide useful "Remote-Party-ID" information. Therefore, I am using "CONNECTEDLINE(num)=xxx" AND "CONNECTEDLINE(name)=yyy" to populate remote party information from a local database. I am also using the "I" (upper case "i") option for Dial. Generally I like to see to see the remote party name appear on the

Hmmm. Ok, that's true. At the very least it will create confusing CDR's I think... maybe. We're not billing our OnNet traffic at all. Only the traffic that goes OffNet, to our switch is billed (if it leaves our switch that is...). I was thinking earlier too that we only need progressinband on traffic that goes to the PSTN, via our switch. OnNet traffic will never generate reorder

Hello, I have question regarding the changes that are made in the sip protocol in Asterisk - the option progressinband. When this option is set to yes in asterisk version 1.4.21.1 - the call flow is: sip.conf: progressinband=yes Device Asterisk -----------INVITE SDP---------> <---------100 Trying------------ <-----183 Session Prgoress-- After version 1.4.2X+ (tested

Hi everyone, We have an Asterisk 1.4.17 user who has problems with sometimes not getting a ring tone on the calling phone. We're considering setting progressinband = yes, but would like to know how much extra CPU load this will require? If anyone can give something even roughly specific (eg "30% increase") that would be great, rather than just "lots". Also, are there any

All, Using SIP with progressinband=yes I get Asterisk to generate the ringing sound for callers. However, I was wondering if it is possible to configure what is 'played back' to the calling party? i.e. instead of just 'ring ring' could I potentially play back a song from an MP3, WAV or GSM file? I'm thinking it would be quite cool to offer a customised 'ring'

Hello, My target system is : PSTN <---> Sip Provider <---IP/ADSL---> Router with fw/NAT <--- SIP/IP/Eth --> Asterisk <--- SIP/IP/Eth --> SIP Phones Asterisk is configured to keep NAT connection with SIP provider open (with qualifyfreq) so I don't have any problem (yet) with either casual incoming or outgoing calls. To work around a possible No Audio when an incoming

Hello! I migrated asterisk 11 to 13 as user of FreePBX 12.0.76.2. As customer of German Telekom, I have three numbers and therefore three trunks - each number is bound to one trunk. After migration, some callers complained about missing ringback tone: they didn't hear any ring tone and where surprised that they suddenly got me anyway :-). The connection afterwards was as expected. Deeper

> Hmmm... I have this aweful feeling that I'm choosing the > exact wrong time to ask a "newbie question" :) Oh well, here > it goes. > > The quick question is : "How do I dial an extension?" > (answer is probably - "you don't" in which case:) "How do I > dial my asterisk box?" - I have no outside line, I just want >

Chris Abel writes: >Hello everyone! > >I've had this problem for a while and cant figure it out. When an outside >caller calls an extension on my asterisk system, they do not hear any >sort of ringing. Inside extensions calling other extensions do hear >ringing. We have 3 other asterisk systems that are configured the same >way, but do not have this problem. We think it

Whoops, email client auto-filled dev previously. Let's try this again. Michael Maier wrote: <snip> > Ok - but this doesn't seem to answer my main question: > > Why must > > progressinband=never > > be applied especially if asterisk uses it by default? The big difference > between w/ and w/o it is: The default in 13 is "no" which still

Hi all I've got an issue where when I call a number that just plays early media back to me. Instead of hearing the full sequence of tones I hear a short ringing then part of the sequence. What seems odd is that I can see the telephone-event/8000 being passed up the chain but when it gets to Asterisk, it is never sent back to the phone. Instead I just see the usual RTP flows. I've been

Hi All, I've been looking for information on how to use asterisk and early media to allow for a video-preview of the caller at the callee's phone for days... but I haven't been too successful :( I found that there seems to be a company "2N Helios IP" which claims (youtube-video) that "their" SIP server is able to provide early video (using a Grandstream 3157v2

I'm evaluating using Polycom phones for our call center and I've set up my first phone (a SoundPoint 560) to give it a try. The phone is working and can successfully place and receive calls. But every minute, there's an error in the log file: chan_sip.c: Registration from '<sip:6193644850 at jtsd05>' failed for '192.168.200.99' - Username/auth name

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 This is slowly driving me nuts! I have several Cisco 7960s with SIP 8.2/7.5 fw connecting to Asterisk 1.2.5 driving a TE110P on a BT EuroISDN PRI line. On all outgoing calls I get a double ring tone (UK style + US style). I also have a DECT phone on a Sipura SPA-3000 configured with UK tones. This gives me a double ring of UK + UK, so this

I have Polycom ip-300 phones that worked yesterday but dont seem to work today (at least dtmf signalling once connected to the asterisk box) The current configuration is: [general] port = 5060 bindaddr = 0.0.0.0 context = test srvlookup = yes dtmf = inband allow = all dtmfmode=inband progressinband=no disallow=all allow=ulaw pedantic=no [202] type=user secret=xxxx context=test mailbox=202

I have a box (Genband) expecting the following: 100 trying 180 ringing with SDP Or 100 trying 183 with SDP And asterisk is sending: 100 trying 180 ringing 183 with SDP Any way to modify asterisk to send what he is expecting? Thanks, Dave -------------- next part -------------- An HTML attachment was scrubbed... URL:

I have this in sip.conf: [general] context=default allowoverlap=no bindport=5060 bindaddr=0.0.0.0 srvlookup=yes progressinband=yes [19256002182] type=friend username=19256002182 callerid="Test hone 1" <+19256002182> host=dynamic canreinvite=no secret=password context=test disallow=all allow=g729 [level3] type=peer host=xxx.yyy.16.99 context=default

Hello everyone! I've had this problem for a while and cant figure it out. When an outside caller calls an extension on my asterisk system, they do not hear any sort of ringing. Inside extensions calling other extensions do hear ringing. We have 3 other asterisk systems that are configured the same way, but do not have this problem. We think it has something to do with asterisk 1.6. The other