similar to: Asterisk stopped Matching Defined Peer

All I've suddenly lost incoming audio on my FWD connection. It worked fine up until Wed when all of the sudden my calls would complete but I couldn't hear any audio (I could see the status of the call on the CLI and could see that my call was using bandwidth on the ethernet switch and router). I swear I didn't change any of the configuration or even restart *, but all the sudden

I am having trouble setting this system up and wonder if some one help me. Does anyone know what is missing if anything to get 2 phones on my asterisk home server to be able to call each other. I have a WRT54GS running OpenWRT/asterisk connected to a PAP2 with 2 extensions 5060/5061, this is on the lan side of my gateway/router WRT54G 192.168.1.1 BusyBox v1.00 (2006.11.07-01:40+0000)

I found this configuration file on Wiki for FWD behind firewall ; SIP Configuration for Asterisk ; [general] disallow=all allow=ulaw port=5060 ; Port to bind to bindaddr=0.0.0.0 ; Address to bind SIP channel to externip=xxx.xxx.xxx.xxx localnet=172.16.1.0 localmask=255.255.255.0 context=inbound-sip ; Default context for incoming calls maxexpirey=180 defaultexpirey=160 tos=reliability

I've been googling and talking with Libretel about my setup and the fact that incoming calls to my asterisk box through the Libretel number reach my box (I hear the greeting being played) but then don't accept DTMF. Here is a rough diagram of my setup: Asterisk | server | NAT <------------ Libretel | router | Note that there are NO SIP

For some reason I now seem unable to control which codec is chosen. The problem happens with outgoing calls to Stanaphone. Even if I chose disallow=all and allow=ulaw as the only codecs it connects with GSM. Has anyone else got problems with these settings? Any suggestions? As I recalled it, such a setup would not establish a call if the ulaw-codec was not offered by the provider. Stanaphone has

I am new to asterisk and need to dig up some info on how to set it all up. It looks a bit daunting especially all the options available in the .conf files. I have 2 SIP phones, GXP2000 and a budgettone 100. phone1 - 192.168.0.160/24 extension 1000 phone2 - 192.168.0.161/24 extension 1001 Server - 192.168.0.57 I get the following all the time, but can make calls between the 2 extensions,

Hi everyone in the asterisk community. Am new to asterisk, while doing the installation I notice that sip.conf examples were not clear for beginners like me so I would like to share my current working configuration with everyone. Swifttel.net is a new VoIP service Provider out of Georgia. Their web site is www.swifttel.net. Currently we have service with them and it has been a pleasant experience.

I'm new to asterisk and need some help with ideas to handle this configuration question. I am trying to establish a termination point/DID number in another country. I am currently running Asterisk CVS-HEAD. My foreign provider uses SIP and authenticates via IP address. I am not required to register my SIP connection in order to send or receive calls. Can someone help me with how to

i've got * and phones in small home network all behind NAT. Outbound to iconnect proxy works great. Now to get in/out working with another carrier. Carrier2, Commpartners, i have working with one of the phones and a soft phone without * just fine. Next I register the phone with * fine. Create a trunk, but it the trunk fails to register... help I'm getting the following msg during

Hi all I am trying to figuure out how to get iconnecthere incoming calls to work outbound works fine but incoming goes nowhere but to my iconnecthere vocemail if I do a sip show registry it shows up as regg'ed nnn=is my iconnect here number xxx is my secret Thank you Jeremy [general] qualify=no register=NNNNNNNNNNN:XXXX@iconnecthere/NNNNNNNNN context=default bind = 0.0.0.0 port=5060

Hi all, I am running an Asterisk server behind a NAT. I want to forward the calls from PSTN to a SIP phone (no nat and also an asterisk). I set the externip and localnet in sip.conf already. I opened the ports in my firewall. (I changed SIP port from 5060 to 5065 and limited the rtp port to 12000-13000) However, I just can't call out. I've always received SIP/2.0 404 Not Found. My

Hi, I can't receive/send calls with Asterisk. Could someone please give me a few pointers on my configuration? Regards, Norman Zhang ; sip.conf [general] disallow=all allow=ulaw port=5060 bindaddr=0.0.0.0 externip=x.x.x.x localnet=192.168.22.0 mask=255.255.255.0 context=inbound-sip maxexpirey=180 defaultexpirey=160 tos=reliability srvlookup=yes register =>

HELP! Ok, so I have the following SIP.CONF: [general] context=default port=5060 bindaddr=10.1.1.200 externip = XX.XXX.XX.XX localnet=10.0.0.0/255.0.0.0 disallow=all allow=ulaw allow=g729 allow=g726 allow=alaw register => ##########@sip.broadvoice.com:XXXXXXXXX:##########@sip.broadvoice.com/1234 [sip.broadvoice.com] type=peer host=sip.broadvoice.com fromdomain=sip.broadvoice.com

I have two phones (111 and 112) on a LAN, and I have on a users site a phone 333. phone 111 uses sip.conf, while 112 uses real-time set-up. 111 can call 333 AND the audio is working 112 can call 333 but audio is just white noise. 333 can call 111 or 112 and audio is working. The phones are identically set-up (just user name = phone number and password are different) sip.conf (for 111 - all

Hello I'm having a difficult time finding precisely what to put in sip.conf and extensions.conf (and possibly other files) to get a working configuration to connect an Asterisk (1.4) server to a VoIP provider with the Asterisk server + SIP clients located in a private LAN behind a NAT router: http://img560.imageshack.us/img560/3749/asterisknat.png Would someone have a full, direct (ie.

I can not register via sip to iptel or sipgate. i do not unterstand why.. but i am new to asterisk. Iam behind a susefirewall2 but asterisk even do not register if it shut down. No answer seems coming back. thx for help. nico here is my config if anybody can help: ----------------------------------------- [general] port = 5060?????????????????????; Port to bind to bindaddr =

Hi there, I am trying to setup a configuration that requires me to use SIP and asterisk behind a firewall and over a VPN to a remote office and with some local Phones also. I can't use IAX to my provider because they don't offer it and my handsets ( snom 300 ) also don't support IAX so it's all SIP. The configuration is a follows Asterisk PBX 10.202.17.217/24 ------>|

Hi, We have some Asterisk servers that we are moving behind a NAT to preserve public addresses and make room for growth. This is Asterisk 1.4 NAT works very good with the externip/localnet-setting when we are connected directly to our teleco. But when I try to use NAT and put them behind our Kamailio something interesting happens: The media-address in the SDP is the internal ip and not the

Hi everybody, I finally want to get rid of 1-way audio problem. Please help me here. I have 3 scenarios. 1. Audio is always one way. Caller who dialed can't listen the called party but called party can listen him. In this scenatio Asterisk is on dynamic IP with dyndns FQDN. sip.conf has externip = abc.dyndns.org and localnet = xxx.xxx.xxx.xxx entry. Trunk and extensions are SIP. Where is

I'm running asterisk on a Freebsd with 2 Nic's. Inside NIC is 192.168.5.x where the phones are. Outside NIC used to be a public IP with the ISP's device set to bridging, but the new WiMAX router only offers me the public ip 94.18.x.x on the outside, and forwarding everything to 192.168.1.50 on the "Outside NIC" Some of the phones are being disconnected with Asterisk