similar to: server specs / hardware

Dear Users, I am fairly new to Digium and Asterisk. I wanted to know that if I use the Digium product THREE Digium Wildcard TE412Ps? (Quad E1 Card) how many calls can I handle simultaneously. I want to use the cards with the following Configurations: Intel? Xeon? 3.00GHz/800MHz, 2M Processor 1GB PC2-3200 DDR2 SDRAM (2x512MB + 2X1GB) memory Integrated Dual Channel Ultra320 SCSI Adapter NC7781

Another day, another apparant unexplained hardware incompatibility. I have a TE412P and a TDM400B living quite happily in a whitebox using an Intel motherboard: http://www.intel.com/design/servers/boards/se7230nh1-e/index.htm I tried to move to an IBM x3650 system. It uses a slightly newer chipset, but apparantly it's in the same family. The SE-7230 board has been EOL'd and the

So, the more I look at various ways to lay out my infrastructure, the more I am thinking about specs for hardware. Starting with firewalling. How does one determine the specs for a firewall? What I mean is: 1. motherboard/CPU - p4? Dual-Core? Intel i3, i5, i7? 2. RAM? 4gb? 8gb? More? 32gb? 3. Obviously GB Nics! I am bring about 300gb of traffic a month right now and I expect that to

Hi all I have a server that has two TE412P (T1/E1+DSP) cards installed. One of them configured as an E1 PRI connected to PSTN and another one configured as a T1 E&M connected to Avaya PBX. Each card only uses two ports, so there are 2 E1 lines and 2 T1 lines connecting to this server. The purpose of this server is as a TDM trunk gateway that gets call from E1/T1 and then forward to an IP-PBX

I'm hoping people can suggest some ideas for debugging a problem that I'm having with DTMF. Unlike most of the DTMF problems reported here, it has nothing to do with Asterisk interpreting DTMF. My problem is with the synthesis of DTMF tones on outbound calls on a PRI connected to a TE412P card. I'm running * 1.4.10.1 with Zaptel 1.4.4. It is important to note that these problems

Has anyone successfully run * 1.4 with the following configuration (or something very similar)? HP DL380 G5 (3Ghz Xeon) CentOS 4.5 (kernel 2.6.9-55) Asterisk 1.4.5 (or 1.4.4) Zaptel 1.4.3 (or 1.4.2.1) TE412P TDM400B (2x FXO and 2x FXS modules) I've had this rig running * 1.2.18 with Zaptel 1.2.17.1 for several months without any issues. Upon trying to upgrade to * 1.4.4 and Zaptel 1.4.2.1 a

Hi, I am about to purchase an Eurotech PRI E1 GSM & CDMA Gateway to operate with my Asterisk's TE412P interface. Anyone here has any experience of having this combination? Any success or failure stories would be greatly appreciated. Thanks in advance. Ash

Hi, I was able to implement T122p one port PRI and was able to call out, but I am planning to use TE412p (includes echo cancellation) 4 port digital card (PRI), I wanted to know can asterisk support 3 four port PRI cards (12 PRI connections) with proper hardware like dual core quadcore processor and 8gb RAM in one server? Also I was planning to implement using 64 bit architecture with Asterisk:

Hello list, I'm currently looking into building a new Asterisk server, due to some codec problems i've got to transcode most of my channels between Alaw -- G729. Is there any indication on how many channels you would be able to transcode on a certain platform? I'm looking into dual Xeon or dual Opteron configurations, which of these platforms would perform better? And how much power

Can I run two instances of asterisk sharing a single te412p ? I want to be able to have several asterisk servers (for testing various scenarios) running on one server. I was wondering if these asterisk processes could share a zaptel/dahdi card nicely. Julian

Hi all, We need to get better echo cancellation on an Asterisk gateway. Currently it has two TE410P (1st gen) cards. So would it be possible to just buy two VPM450M cards ? Or do we need to buy two new TE412P cards ? In that case a Sangoma A108d card would be nice as well ? What configuration gives the best audio quality ? Thanks, Leon de Rooij leon at scarlet-internet.nl

On 3/22/2018 8:06 PM, David Minard wrote: > G'day All, > >     Will replay to all messages so far in this one to keep it all > together. > > On 21/03/18 22:52, lingpanda101 wrote: >> On 3/21/2018 7:32 AM, David Minard via samba wrote: >>> Thanks Carlos, >>> >>> The thing is, that I did not upgrade the version of Samba - that is >>>

Just to share some experience with everyone about what happened today to our Asterisk 1.4 box with Digium TE412P card. We had an unscheduled power outage which shut down the Asterisk box. When the power went up, Asterisk came back up okay but the ports on the card were all red. Zttool show red alarm and cat /proc/zaptel/1 show red alarm today. Both incoming and outgoing cannot be made. When a

Can someone point me in the right direction to find documentation on best practices when setting up a new Asterisk server? I'm using RHES4 and Dell 1750 with TE412P. My current problems are frequent crashes and choppy audio so I think I can easily tweak these out of the picture. -------------- next part -------------- An HTML attachment was scrubbed... URL:

I've got a system with a TE412P installed under Fedora Core 6 and I continue to see this message in the logs. The card most certainly does have an EC module installed. The system is suffering from echo problems, and I suspect this is no coincidence... I've double checked to ensure the module has been inserted correctly. I've not seen any other complaints on the lists, etc. about this

Hi all, I have 1 Card Digium TE412P and 2PRI E1. I have more problems with drops lines. The asterisk log is this: May 16 10:52:26 NOTICE[4465]: chan_zap.c:8194 pri_dchannel: PRI got event: Alarm (4) on Primary D-channel of span 1 May 16 10:52:26 WARNING[4465]: chan_zap.c:2287 pri_find_dchan: No D-channels available! Using Primary channel 16 as D-channel anyway! May 16 10:52:26 NOTICE[4465]:

TE410P card down. I have three (3) TE410P in one machine running asterisk with SS7. My problems started last week when one of my cards started switching to E1 every time after reboot. I set the following in dahdi.conf and that solve the problem. /etc/modprobe.d/ options wct4xxp t1e1override=0x00 Now all 4 ports on that card is down with Red Alarm. I tried rebooting the machine and

On 3/25/2018 8:54 PM, David Minard wrote: > > > On 24/03/18 01:35, lingpanda101 wrote: >> On 3/22/2018 8:06 PM, David Minard wrote: >>> G'day All, >>> >>>     Will replay to all messages so far in this one to keep it all >>> together. >>> >>> On 21/03/18 22:52, lingpanda101 wrote: >>>> On 3/21/2018 7:32 AM, David

Dears What's the major deference between Asterisk 1.6.0.6 and Asterisk 1.4.23 Regards Khaled Chehab NGN Eng. Untitled Operations Office - Lebanon Office : +961 1 868686 ext 115 Mobile: +961 3 045212 E-mail: <mailto:bsara at mg-tel.com> Kchehab at Xplorium.com MSN ID :KhalidChehab at hotmail.com Web Site:

One of our interns had to run down to the datacenter today and rescue an ailing 4.2 machine and the decision was made to just do a fresh install and restore a backup from last night. The only problem was that she had forgotten the 4.2 DVD in the office, a 2 hour drive back and forth. So I suggested she fire up her notebook which has a DVD burner and download the DVD via bitorrent instead.