similar to: Digium Iaxy S100 Factory Default?

Hi, I have three Iaxy devices (s101i) parts. Two of them seem to work fine. The third plays a loud repeating click sound when an analog phone is plugged in. I can provision all of them, and make calls to all of them. The clicking one will blink when a call is incoming, but no audio from the call can be heard on the handset, and the caller only hears silence. The same handset works on the

Hi, I'm having an issue with a soekris net4801 board and a S101i "IAXy" device. When I connect a successfully provisioned IAXy directly via a crossover cable into an ethernet port of the soekris, the link led turns on orange so i'ts 10Mb and the activity led blinks like if there is some action going on but when I try 'tcpdump -nettti sis1' I see nothing going on, no

I have one Digium adapter S101I on a local network and I'm losing the connection periodically. I'm using Asterisk-1.2.21.1 There is no pattern, sometimes it stays connected for a weak sometimes longer. In comparison I have few Sipura adapters and they stay connected for months (never lost single connection). -- #Joseph

Does anybody know what DTMF coding does S101i adapter using? I've been testing one for over a week and here are my observations: - DTMF signaling is working perfectly with Asterisk, much better than Sipura 3K Though, I think the Asterisk "iaxy" firmware is buggy, the unit is using auto-update feature; so I have Asterisk 1.2.13 and iaxy firmware version is: 23 When enable in

I'm having a problem with my IAXy not always connecting to my Asterisk box. When I pick-up the phone plugged in to the IAXy I get a busy signal. I have to hang-up the phone and wait a few seconds after the orange LED goes out and then try again. When this happens I don't see any connection attempts in the Asterisk -r output. When I do get the IAXy to connect to Asterisk I get a

Hi.. I have to setup an extension in a remote location that will use a cordless analog telephone.. I am looking at the IAXY to do this for me..Basically the data path will be as follows... [Asterisk] == (NAT) == {Internet} == (NAT) == ATA -- Handset Since there are two NAT boxes in the path I know SIP won't work.. I also don't want to move the Asterisk box to the internet side of the

I just saw the S100-FX v2.0 on eBay. I was wondering if anyone has tried it out and what their opinion of it was. ---- Mike Hammett Intelligent Computing Solutions http://www.ics-il.com -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20060126/3da2e4e5/attachment.htm

Hi. Does anyone know about a simple one-fxs ATA with pulse dialing support that can work with Asterisk? A SIP one would be ok. I've been told that the Digium S101i IAXy does support pulse dialing; although it's a iax2-only ata it could be enough. I need a bunch of them to convert some old fashioned rotary phones into VoIP ones (I'd like to disassemble the ATAs to remove the boards

John Novack wrote: >And the only IAX2 box made is the Digium one, with it's current shortcomings ? >From reading through the archives, it seems there is currently no way to reset to factory default, no >written MAC address on an individual box, and some other instabilities requiring frequent resets. Yeah, there's the rub. Dunno if it's worth it, I'm willing to give it

I have a brand new IAXy I'm playing with. I do not get a dialtone on the phone, or any response at ll on the phone. No sound, no dialing, no ringing. The phone and wire are tested and known to be good. I think I have it setup correctly. When I give the iaxprov command I get this: #iaxyprov 192.168.1.90 iaxy.conf 02: c0 a8 01 5a 05: 11 d9 03: ff ff ff 00 04:

Hi, I've got an IAXy, and provided it with connection data - unfortunately didn't provide a fixed ip address, but left with dhcp. Everthing went fine, and I could work a while with it. After a restart of IAXy, it didn't negotiate a new IP address, nor used the old one. I even restarted the DHCP server and cleared its cache. No success. I went to another office with a different

Hey Everyone, I recently purchased a few IAXy units for some testing, and have come across a some problems. One of them can be provisioned but will not ring the connected telephone. It also does not provide a dial tone when you pick up the phone. When a call is made to the IAXy one of the green lights on the board goes from a solid on state, to a flashing state that coincides with the

The file used with a Digium IAXy device: "iax.conf" has the line: "port=5036" (I also use the "bindaddr=192.168.1.91" entry) but when Asterisk talks to the IAXy device it used port 4569 (from "tcpdump"). How are the port numbers assigned? What tells the IAXy which port to use. The IAXy provisioning file "iaxy.conf" file does not specify a port

The file used with a Digium IAXy device: "iax.conf" has the line: "port=5036" (I also use the "bindaddr=192.168.1.91" entry) but when Asterisk talks to the IAXy device it used port 4569 (from "tcpdump"). How are the port numbers assigned? What tells the IAXy which port to use. The IAXy provisioning file "iaxy.conf" file does not specify a port

Ok, I searched the lists and found no definitive answer. I'm assuming the IAXy has some primitive form of echo cancel, is there anyway to adjust this? Or any ideas on what to do instead. Here's the setup, this will not be a typical setup for our company however, well whatever. Anyway it looks like this: IAXy --> Netgear router --> Charter --> Level3 --> Asterisk --> VOIP or

Yesterday I was using one of the cheap Radio Shack phone polarity on various phone outlets in my house and ended up plugging it into my IAXY. While the regular phone jacks tested OK, the IAXY tested as being reverse polarity. The tester was plugged directly into the IAXY so there is no chance of this being caused by crossed wires. Is this something that is misconfigured on the IAXY, a hardware

Hi! Could someone please tell me where in the CVS tree the IAXY firmware is and the utility used to install/flash the IAXY? Or a perhaps cvs command that shows me which directories are available in the CVS? I did 'man cvs' but can't find such a command or flag. Also is there any documentation for the IAXY in the CVS tree or anywhere or C comments I can read somewhere to glean some

I bought an IAXy just about a week ago, and I'm having a problem with it. I provisioned it without any problems. It's on the same network segment as my Asterisk server. It registers just fine. When I call from the IAXy to a Zap channel, it works fine. When I call from a Zap channel to the IAXy, I don't get any audio from the IAXy, only from the Zap to the IAXy. Near the beginning

For anyone playing around with IAXy(S100i) devices, I am making the following available: Windows IAXy Provision v1.00 This is a from-the-ground-up development of a means of provisioning IAXy devices using a Windows environment. For some users, being bound to Linux for IAXy provisioning is not viable or convenient in some cases. This application provides a GUI data entry for the various IAXy

Hi all, I have a Soekris net4801-50 board with OpenBSD 3.9 where I've configured a dhcp server and tested it with a regular PC connected directly via a crossover cable with success. The problem comes when I try to connect my IAXy device instead of the PC. I can see with 'tcpdump -nettti sis1' that the IAXy isn't sending any packets to the dhcp server. I thought my IAXy was bad