similar to: IAX access to FWD broken?

hi i've configured a Beronet BN8S0 Card with misdn beronet utility. the card is configured with all lines in TE and P2P mode, and it is connected with the special cable with an ISDN connection. i've turned on debugging to level 4, this is the output from the asterisk cli when i receive a call: P[ 5] MGMT: Short status dinfo 1000001 P[ 5] MGMT: SSTATUS: L1_ACTIVATED P[ 5] handle_frm:

Use Set(CALLERID(num)=9999999999) instead of using CALLERID(all). Remember to set this BEFORE you Dial. -->> -----Original Message----- -->> From: asterisk-users-bounces at lists.digium.com [mailto:asterisk-users- -->> bounces at lists.digium.com] On Behalf Of Vieri -->> Sent: 06 February 2009 12:36 -->> To: asterisk-users at lists.digium.com -->>

You're quite right. We'll need to see your misdn.conf file to check the settings. -->> -----Original Message----- -->> From: asterisk-users-bounces at lists.digium.com [mailto:asterisk-users- -->> bounces at lists.digium.com] On Behalf Of Vieri -->> Sent: 06 February 2009 13:49 -->> To: asterisk-users at lists.digium.com -->> Subject:

I am trying to use misdn insted of zaphfc to drive two billion isdn cards zaphfc is ok, but the problem with cdr and the fact tha you always have to wait the bristuffed version of asterisk took me to try another way. so I downloaded the misdn installation script from beronet for the last version ( I am using asterisk stable 1.2, so now is 1.2.5) wget

Hello everyone. I've got this really annoying HFC Cologne card (or however I should call it - a single channel ISDN card based on the HFC chipset). It wrongfully detects lots and lots and lots of incoming DTMFs, to the point the card is not usable. Here's a sample out of CLI: P[ 1] I IND :DTMF_TONE oad:206361 dad:520101 P[ 1] --> mode:TE cause:16 ocause:16 rad: cad: P[ 1] -->

Hi, I have an FWD account and it's configured in asterisk. I can be called by people using FWD, but I cannot make FWD calls myself. Every number dialed with a 8 prefix goes to FWD, if for example I call the echo servie I get this: Connected to Asterisk 1.2.13 currently running on asterisk (pid = 2865) Verbosity is at least 35 -- Executing SetCallerID("SIP/timothy-08224f08",

Hi, I have 10 DID numbers. Calls coming from the PSTN network are routed correctly to the SIP users based on the number that was called. But when sip users call the PSTN network, the CallerID should be set to correspondent with their DID number. At the moment I can set the CallerID to a global number, but I have no idea how to check who's making the call. All sip users start in the context

Hi, I'm installing Asterisk on Ubuntu 6.10 When I first compiled the zaptel package I used: make clean make make install So far so good, but the following command failed: make b410p I did some digging on google and found a guide on how to install it manually, but the result was the same. I got these files ftp.digium.com/pub/telephony/zaptel/b410p/misdn-b410p.tar.gz

Hello, Following my first mail about this issue [1], I think I know now what the problem is. When I have both lines being used and a third call comes in, the person calling doesn't get a busy tone, he gets something like line unavailable. I've been debugging mISDN and I think the reason is because asterisk is sending the release cause as 0. P[ 3] --> channel:0 mode:TE cause:0

Hi, I've been able to make make install the Zaptel drivers (1.2). I'm using a b410p so I executed the following command make b410p. I tried this on multiple machines, but it always failes: root@asterisk:/usr/src/zaptel-1.2.11# make b410p [ -f misdn-b410p.tar.bz ] || wget ftp://ftp.digium.com/pub/zaptel/b410p/misdn-b410p.tar.gz --23:59:54--

Hi, Hi All, I've just delved into the world of asterisk and I'm having a few dtmf issues. Internally, amongst sip phones, dtmf is fine. Externally, if you ring from a GSM mobile, DTMF is fine, however if you ring from a standard phone, DTMF fails to register. I am attempting to use a quad port HFC-4S Beronet Card. I've been searching the web most of the last week and

Hi, I have written a package that contains many s4 generic functions and associated methods. I am having a lot of trouble getting R to build the help pages for these generic functions without reporting, "missing link(s): ~~fun~~, which means that it cannot find the appropriate function when code in the example section of the help is run. Right? After some playing around I can get it to

Hi, i use an BN4S0 with misdn an asterisk on Linux 2.6.9. The hfcmulti module is loaded with option: type=0x04 protocol=0x2,0x2,0x22,0x2 layermask=0xf,0xf,0xf,0xf and the fourth port is connected to an ISDN PTMP (MSN) port. Call to #72 from S0 (BN port 4) are not accepted from asterisk but why ? Can anyone give me a hint ?? misdn debug messages follows: lib: NEW_CR Ind with l3id:80001

I have a North American BRI configured as National ISDN (NI-1) on an SBC (Nortel?) switch. SBC calls this "FastTrak ISDN", and it's surprisingly inexpensive -- less than two POTS lines. I've been trying to find an inexpensive PCI interface solution to connect this to Asterisk as voice lines. I prefer ISDN BRI over POTS lines because of the improved signalling, fast dialing,

Hi, Since a week ago I am trying to get chan_misdn working with asterisk 1.4.19, using HFC based ISDN card on Linux 2.6.22. My setup is done as detailed on wiki and FAQ. * mISDN and miSDNusers are 1.1.7.2, unpacked, build and installed. After installation and misdn-init, I have this: aragorn:root/pts/1: # misdnportinfo Port 1: TE-mode BRI S/T interface line (for phone lines) ->

Hi. I'm running Asterisk server with 10 sip phones, and 2 grouped T0 lines with 10 DDI numbers. My provider is France Telecom and my setup is : - Debian Lenny - Asterisk 1.4 - Linux kernel 2.6.25.17 - mISDN 1.1.8 driver - Sip phones Thomson ST2030 No problem with the SIP . But when reveiving a call on RNIS line (any of the DDI numbers), the associated SIP phone rings indicating _two_

i am using asterisk 1.6.2 with mISDN and a passive AVM Fritz!card on CentOS 5.5. The only thing, i want to do is a call-redirection from an isdn-call to my mobile via sip-account. My extension conf is: general] static=yes writeprotect=no [globals] OUT_PORT=1 [ISDN] exten => 12345,1,Dial(SIP/012346737222 at sipprovider.local) If i call to the msn 12345, the SIP-call is going out, but after

I'm trying to set caller ids on outgoing calls. I have a quad BRI B410P card connected to my telephony provider. I know the list of DID numbers the provider assigned to my company. If I don't set the caller id then the callee always sees the same "top-level" number. If I set the caller id to a specific DID number we own, the callee keeps seeing the "top-level" number,

Hello I want to compile some R-packages under windows (rmutil and revent for instance from Pr Lindsey) I followed the instrictions given in the help. The compilation succeeded, but I can't run the programs. I receive the message: "error in dyn.oad(file): unable to load shared library "C:\R\Rwo650/library/rmutil" LoadLibrary failure. I found the given path quite strange!!

Odette > Wondering how can I generate "Akaike weight" with R? I know the description, > but is there any function to generate by R on the web-site or R library? > I am using GLM or GLMM (family=binomial), so would be appreciated if you > help me. You could have a look at this. http://bm2.genes.nig.ac.jp/RGM2/R_current/library/aod/man/summary.aic.html Which is in the OAD